manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Crown
  6. •
  7. Car Alarm
  8. •
  9. Crown CR-3000 Use and care manual

Crown CR-3000 Use and care manual

- 1 -
AUTO SECURITY SYSTEM
MODEL: CR-3000
MANUAL FOR
USERS & INSTALLERS
Caution : Any changes or modifications in construction of this device which are not
expressly approved by the party responsible for compliance could void the user's authority
to operate the equipment.
FCC statements
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
- 2 -
CONTROL REMOTE
1. ARM 2. DISARM 3. MUTE
ARM 4. MUTE
DISARM
CRO WN
CRO WN
CROWN
CRO WN
1. ARM (LOCK) : Press #1 (±) button
2. DISARM (UNLOCK) : Press #2 (²) button.
3. MUTE ARM : Press #3(T) button, and Press #1 (±) button.
4. MUTE DISARM : Press #3(T) button, and Press #2 (²) button.
5. CHANNEL 2 6. REMOTE PANIC 7. CAR FINDER
CROWN
CRO WN
CROWN
5. 2nd CHANNEL (TRUNK) : Press #3(T) button for 3 seconds
6. REMOTE PANIC : Press #1(±) button for 3 seconds
7. CAR FINDER : Press #4(F) button for 2 seconds
CHARACTERISTICS
a. Alarm with two channels
b. Two transmitters with 4 buttons
c. Siren of 6 tones of 128dB
d. Integrated shock sensor with double (minor/major) protection
e. LED indicator
f. Two kinds of valet systems with valet switch or transmitter
g. Memory system of intrusion
h. Arming notification when doors open.
i. Siren cancellation by transmitter
j. Harness integrated with blade fuses
- 3 -
CONTENTS
a. Main brain with integrated double guard shock sensor
b. Two remote controls ( transmitters)
c. Harness with blade fuses
d. 6-tone siren
e. LED indicator
f. Valet/ override switch
g. Manual for users and installers
FUNCTION PROGRAMMING BY INSTALLERS
a. Automatic re-arming ÆOn / Off (IGN On – Door open - Valet 8 times - #1)
b. Automatic (passive) arming ÆOn / Off (IGN On – Door open - Valet 8 times - #2)
c. Ignition lock / unlock ÆOn / Off (IGN On – Door open - Valet 8 times - #3)
d. Pulse time of lock / unlock Æ0.8 sec. / 3.0 sec. (IGN On – Door open - Valet 8 times - #4)
e. Double unlock pulseÆOn (Double Unlock) / Off (IGN On – Door open - Valet 8 times - #1 + #2)
f. Shock sensor ÆOn / Off (IGN On – Door open - Valet 8 times - #3 + #4)
g. 2
nd Channel Mode ÆMomentary / Continuous (IGN On – Door open - Valet 8 times - #1 + #3)
h. Siren or horn ÆSiren / Horn with Relay (IGN On – Door open - Valet 8 times - #2 +#4)
SELECT FUNTION BY USERS
a. Mute arm or mute Disarm (#3 - #1 / #3 - #2)
b. 2
nd channel (for trunk or sunroof ) (#3 for 3 seconds)
c. Remote panic (#1 for 3 seconds)
d. Car finder (#4 for 2 seconds )
e. Valet mode with transmitter (door open - IGN On - #4 for 3 seconds On / Off)
f. Deletion of shock sensor (IGN On – Door open - Valet switch 8 times - #3 + #4) by transmitter
FUNTION’S TABLE OF TRASMITTER
BUTTON CONDITIONS FUNTIONS ACTIONS
# 1, press one time Ign off +
Door closed
Arm (after 3 sec.)
close securities Siren: 1 chirp
Light :1 flash
LED: slowly (every 1 sec.)
Doors locked
Starter disable (block of starter motor)
Door opened Notification 3 Chirps
#2, press one time Ign off Disarm
opensecurities Siren: 2 chirps
Light: 2 flashes
LED: off
Doors unlocked
Starter enable
(Triggered) (History) Siren: 4 chirps
Light: 4 flashes
LED: Rapidly (every 0.5 sec.)
# 3, press 3 sec. Ign off 2
nd
Channel Trunk, etc
# 3 one time - # 1 Ign off Mute arm Arm without sound temporarily
# 4 one time Ign off Car finder Siren: 7 chirps
Light: 7 flashes
# 1 for 3 sec. Ign off Remotepanic Action of Siren+ Light
# 3 one time - # 2 Ign off Mute disarm Disarm without sound temporarily
# 4 for 3 sec. Door open
Ign on Remote valet
(for enterance) Siren: 1 chirp for entrance
LED: on continuously
# 4 for 3 sec. Door open
Ign on Remote valet
(for exit) Siren: 2 Chirps for exit
LED: off
- 4 -
PROGRAM OF TRANSMITTERS
a. Turn ignition on and open a door first and then press Valet/Override switch 4 times (within 15
seconds), then LED will be on continuously and siren will emit 1 long chirp. You are now in the
stage of programming mode.
b. Press # 1 button then siren will emit 2 short chirps 4 times.
c. Turn ignition off. LED will be off and siren will emit 4 chirps. You are now in stage of exiting
programming mode.
d. You can repeat this and have maximum 4 programmed transmitters per module. If you program
new transmitter, we recommend to delete old code memory and to re-program all existing
transmitters. You can have this job up to 4 times by same way above.
ACTIVATION OFARMING
a. Exit the vehicle and close all entrances.
b. Press # 1 button at once.
c. Siren chirps 1 time, light flashes 1 time and LED flashes slowly every sec.
d. All protected entrances are armed.
e. Starter kill enableÆStarter disables relay which is activated and prevents the engine cranking.
f. If any entrance is opened, siren chirps 3 times and LED flashes rapidly for notification. When
door is closed, the arming will start.
g. After 3 seconds of arming, alarm system will be activated. Shock sensor will not be activated
during 3 seconds. It will be re-activated in more than 3 seconds and the sensor becomes stable.
ACTIVATION OF DISARMING
a. Press #2 button at once.
b. Siren chirps 2 times, light flashes 2 times and LED off.
c. All protected securities will be disarmed.
d. Starter kill disableÆStart motor can be enabled
e. Memory of intrusion: If siren chirps and light flashes 4times when you disarm the alarm, this
notifies alarm has been triggered. Rapid LED flash every 2 times notifies electric security has been
triggered, while every 3 times LED flash notifies door had been triggered.
MUTE ARMING/ DISARMING
a. Press # 3 one time, then press # 1 one time within 3 seconds to enter Mute Arming.
b. Press # 3 one time, then press # 2 one time within 3 seconds to enter Mute disarming
DEACTIVATION OF EMERGENCY
If transmitter is lost or damaged when alarm system is activated arming,
following process is needed .
ÆEnter Valet Mode first
ACC IG
OFF
START VALET SW -8-TI MES
Opena Door
- 5 -
a. Turn ignition on.
b. Open the door.
c. Press Valet/ Override switch for 3 seconds to enter valet mode (ignition valet)
REMOTE PANIC
a. Press and hold #4 for 3 seconds, the siren will sound and light will flash for 60 seconds.
b. Press any button to turn off panic alarm.
CAR FINDER
a. Press #4 within 2 seconds.
b. Siren will sound 7 times and light will flash 7 times.
SHOCK SENSOR
a.Sensibility can be adjusted by turning the volume right (more sensitive) and left (less sensitive).
b. If the car receives a soft shock, siren chirps 5 times and light flashes 1 time for the purpose of
protection.
c.If the car receives a hard shock, siren chirps continuously for the purpose of protection.
(LAST DOOR) AUTOMATIC (PASSIVE) ARMING - PROGRAMMABLE
a. Turn off the ignition key and exit the vehicle. When last protected entrance is closed, siren chirps 1
time and LED begins to flash rapidly.
b. After 30 seconds, all security systems will be armed automatically (without signal from the
transmitters).
AUTOMMATIC RE-ARMING
a. Alarm is disarmed when ignition is not turned to the position of “Off” and if any entrance is not
triggered for 30 seconds.
b. System will activate automatically and close all security to return arming.
2nd CHANNEL
a. When ignition is off and all systems are deactivated, press #3 for 3 seconds to operate 2nd channel.
b. Momentary output for trunk or continuous output for others can be selected by program (Pre-
programmable)
IGNITION CONTROLLED LOCK / UNLOCK (PROGRAMMABLE)
a.Turn the ignition on, then door will be locked after 3 seconds.
b.Turn the ignition off, then door will be unlocked immediately.
VALET MODE – TWO VALET MODES: TRANSMITTER OR VALET SWITCH
a. In the valet mode:
1) Sound (siren or horn) and electric securities will not be activated.
2) Lock / unlock and parking light will be activated.
b. Valet (normal)
1) Turn the ignition on and open the door, then press valet / override switch for 3 seconds until
siren sounds 1 chirp.
2) To exit valet mode, turn the ignition off and open the door, then press valet / override switch for
3 seconds until siren sounds 2 chirps. LED will be off. This indicates that system is on already
valet mode.
c. Transmitter (remote) valet :
1) Turn the ignition on and open the door, then press remote #4 button for 3 seconds until siren
- 6 -
sounds 1 chirp.
2) To exit valet mode, turn the ignition off and open the door, then press remote #4 button for 3
seconds until siren sounds 2 chirps. LED will be off. This indicates that system is on already
valet mode.
SELECT FUNCTIONS
FUNCTIONS PROGRAM SETTING DEFAULT OPTION
1 Re-arming Mode #1 *Off On
2 Automatic (Passive)
Arming & Passive
Locking
#2 *On Off
3 Ignition Lock / Unlock #3 *On Off
4 Times for Lock / Unlock #4 *0.8 sec. 3.0 sec.
5 Double Unlock Pulse #1 + #2 *Off On (Double
Unlock)
6 Shock Sensor #3 + #4 *On Off
7 2nd Channel Output #1 + #3 *Momentary
(Trunk) Continuously
(others)
8 Siren or Horn (relay)
IGN On +
Open a Door
Press Valet button
for 8 times
#2 + #4 *Siren Horn
SIREN CHIRP
a. One time : Alarm is armed
b. Two times : Alarm is disarmed
c. Three times : Door is opened
d. Four times : Memory of intrusion
e. Six times : Minor shock
f. Seven times : Car finder
STATUS INDICATOR
a. Arm: LED flashes slowly (every 1 second)
b. Disarm: LED Off
c. Automatic (Passive) arming and automatic rearming: LED flashes rapidly for 30 seconds.
d. Valet Mode: LED constantly on
e.Memory of intrusion in electric securities: LED flashes rapidly in a 2 step sequence.
f. Memory of intrusion on doors: LED flashes rapidly in a 3 step sequence.
- 7 -
CROWN Installation Diagram
+
W
HITE Parking Light Output
RED 12Volt Constant Input
BLACK Chassis Ground Input
YELLOW 12Volt Ignition Input
ORANGE Starter Ground Output
BROWN
VIOLET
GREEN
BLUE Output
W
HITE/BLACK Lock Output
RED/WHITE 2nd Channel Output
Siren(or Horn) Output
Door Pin Input
Door Pin Input
10PIN HARNESS 2P
W
HITE
W
HITE
(Trunk)
BLUE
A
dditional device Input
Valet SW
Status LED
2P
RED
Lock
85
86
8787a
30
START
MOTOR
* Starter Ground Output
Ignition Key
* Double Guard Shock Sensor
HORN
85
86
8787a
30
(-)Horn: Additional relay(Programable)
* Siren Output
BAT12V
BAT12V
ANT
BLACK
LIGHT JUMPER
FCC NO. TIF1CROWN05-M

Popular Car Alarm manuals by other brands

Viper 300+ installation guide

Viper

Viper 300+ installation guide

Drone DR-2000 install guide

Drone

Drone DR-2000 install guide

CrimeStopper CS-2004 WDC Installation and operating instructions

CrimeStopper

CrimeStopper CS-2004 WDC Installation and operating instructions

Directed Electronics 690XV owner's guide

Directed Electronics

Directed Electronics 690XV owner's guide

Viper 5606V owner's guide

Viper

Viper 5606V owner's guide

CrimeStopper CS-9711 Installation handbook

CrimeStopper

CrimeStopper CS-9711 Installation handbook

Viper SmartKey VSK100 Quick reference install guide

Viper

Viper SmartKey VSK100 Quick reference install guide

DEI 820M owner's guide

DEI

DEI 820M owner's guide

Pandora DXL-1700L manual

Pandora

Pandora DXL-1700L manual

Clifford 5806X owner's guide

Clifford

Clifford 5806X owner's guide

Soundstream Tarantula AL.3 installation guide

Soundstream

Soundstream Tarantula AL.3 installation guide

Black Widow BW-1020 NEW AVENGER installation manual

Black Widow

Black Widow BW-1020 NEW AVENGER installation manual

Viper 4103XV installation guide

Viper

Viper 4103XV installation guide

Viper 3305V owner's manual

Viper

Viper 3305V owner's manual

Audiovox Pursuit PRO 9842B installation instructions

Audiovox

Audiovox Pursuit PRO 9842B installation instructions

Clifford SE 5000 owner's manual

Clifford

Clifford SE 5000 owner's manual

KEETEC TS 8000 user manual

KEETEC

KEETEC TS 8000 user manual

DEFA 800 installation manual

DEFA

DEFA 800 installation manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.