CTA PAD-SCGS User manual

Compact Security Gooseneck Floor Stand
PAD-SCGS
INSTRUCTION - MANUAL
888-733-4448
CONTENTS:
1. Attaching Foam Pad to Tablet Holder
Select the appropriate foam pad (N) according to the
thickness of your tablet (or tablet in its case), then
press adhesive side into center of tablet holder.
2. Installing the Swivel Casters
INSTRUCTIONS:
A
N
A
K
I
2a. Place a
spring washer (I)
over the screw
bolt on each
caster (E).
2b. Place the
screw bolt from
each wheel (E)
through the
metal base (C),
then place a nut
cover (H) over
the top of each.
Screw down
clockwise by
hand, then use
wrench (G) to
tighten further.
Wheel
Screw Nut Cover
Spring
Washer
Metal
Base
Use this table to determine the
appropriate foam pad to use
with your tablet.
Note: sizes refer to total tablet
size with or without a case.
Foam Pad
Thickness
Tablet
Thickness:
1mm 0.67-1.06in
5mm 0.51-0.91in
10mm 0.31-0.71in
17-27mm
13-23mm
8-18mm
/
/
/
1mm Foam Pad
5mm
Foam Pad 10mm
Foam Pad
x1
Bx1
x2
C
D
x1
x4
H
x4 x4
G N
x4
L
x8
M
x4
E
x1
F
x1
J
x4
x1
O
E
I
E
G
C
H
x1

888-733-4448
Metal connection
Height
Adjustment
Knob
Pole (B)
Metal
Cross Base (C) x2
Connection Screw Bolt (K),
Washers (L) and Nut (M)
Pole Assembly and Pole Nut
Cross Base Sections (2)
Allen Key (J)
3a. Place the metal base of the base pole (B)
with the higher piece on top of the cross
base (C). Align the holes at the bottom of the
pole (B) with the holes on the cross base (C).
3b. Insert a screw bolt (K) with a
washer (L) into each of 4 holes.
Place another washer (L) on the
underside of each screw bolt. Grip
the nut (M) on the underside with
one hand, and use the other tighten
each screw with the allen key tool
(J). Repeat for all four screw bolts.
3. Base Assembly and Connecting the Metal Cover
3c. Rotate the grip counter
clockwise to loosen
completely and remove from
the top of the pole.
3e. Place the grip back over
the stand pole (B) and rotate
clockwise until securely
tightened.
3d. Place the square metal
cover (D) over the top of the
pole (B) and slide down to
the stand base.
4. Connecting Gooseneck
Holder & Battery Case
5. Installing Tablet Device
Adjusting the Floor Stand
4a. Place battery
case (F) over top of
metal connection.
Note: if the Y screw
is already in,
unscrew before
attaching the
gooseneck.
4b. Screw the
gooseneck onto the
metal connection of
the pole by turning
clockwise. Be sure
that the battery case
is on the opposite
side of the pole as
the Y screw.
5a. Insert key (O) and set
position to unlock. Remove key,
then slide holder (A) open.
Tighten and loosen
the holder connection
screw to adjust ease
of rotation.
Adjust the gooseneck
to desired position.
Rotate plastic grip to
loosen, then adjust
pole to desired height.
Rotate back to tighten.
5b. Load tablet corner first into
one end. Insert key and set to
lock, the slide holder shut until
secured. Remove key.
4c. Turn the Y screw
clockwise to tighten
the connection.
Y Screw
K
D
B
B
A
B
A
F
F
M
L