Cub Cadet XR5 Installation manual

Original user instructions
ADDITIONAL INFORMATION
XR5 models

ADDITIONAL INFORMATION
EN

2
Safety first
Maintenance and Cleaning
3 sec
1. Switch off the robot
2. Remove the disabling device before doing
any maintenance
EN

3
Blade Replacement
Periodically inspect the blades and replace them if damaged.
It is recommended to replace the blades per the table below.
Always replace all 4 blades, including the screws
< 500 m² Every 8 - 10 weeks
500 m² - 1000 m² Every 6 - 8 weeks
> 1000 m² Every 4 - 6 weeks
Watch the video
EN

4
Cleaning
The XR5 wheels and deck are self-cleaning. Accumulated grass, soil and
debris will disperse when dry conditions return.
Every 1-2 weeks, clean the robot underneath.
Remove debris
from the wheels
EN

5
Remove debris between
the guard wires
Use a soft brush to remove
debris from the mowing deck
EN

6
During longer periods of increased wet conditions, mud and mulch can
accumulate on wheels. It is recommended to attach the wheel cleaners
accessories to assist in removing debris in these conditions.
Insert each wheel cleaner
into its respective slot
Left wheel Right wheel
L
L
R
STOP
STOP
R
Install the wheel cleaners
Watch the video
EN

7
Press wheel cleaner firmly into
slot until it is securely in place
EN

8
Technical Spec XR5 1000 XR5 2000
Recommended lawn size [m2] Up to 1000 m2Up to 2000 m2
Cutting width [cm] 21 21
Cutting height [mm] 15-100 15-100
Sub-zones 4 4
Separated zones
Wire [m]
Number of pegs
Mowing motors DC Brushless DC Brushless
Drive motors DC Brushless DC Brushless
Spare blades 8 12
Max. incline mowing area 45% (24°) 45% (24°)
Max. incline wire on slope 20% (11°) 20% (11°)
Maximum allowed perimeter wire length 800 m 800 m
Sound pressure level Lpa dB(A) (K=3) 50 50
Measured sound power level Lwa, dB(A) 61 61
Guaranteed sound power level Lwa, dB(A) 64 64
Mowing time [min] 40-50 80-90
Charging time [min] 60-120 60-120
Battery type 18,5V Li-Ion 18,5V Li-Ion
Battery capacity spec [Ah] 4.9 4.9
Power consumption [kWh/month] 4 7.3
Anti-theft
Bluetooth (BLE)
GSM module
Near Wire Following (MBLE)
Max altitude 3,000m 3,000m
Warranty 3 years 3 years
Mowing time and lawn size based on ideal mowing conditions.
EN

9
Mowing time and lawn size based on ideal mowing conditions.
Technical Spec XR5 3000 XR5 4000
Recommended lawn size [m2]Up to 3000 m2Up to 4000 m2
Cutting width [cm] 42 42
Cutting height [mm] 15-100 15-100
Sub-zones 4 4
Separated zones
Wire [m]
Number of pegs
Mowing motors DC Brushless DC Brushless
Drive motors DC Brushless DC Brushless
Spare blades 16 24
Max. incline mowing area 45% (24°) 45% (24°)
Max. incline wire on slope 20% (11°) 20% (11°)
Maximum allowed perimeter wire length 800 m 800 m
Sound pressure level Lpa dB(A) (K=3) 53 53
Measured sound power level Lwa, dB(A) 64 64
Guaranteed sound power level Lwa, dB(A) 65 65
Mowing time [min] 80-90 110-120
Charging time [min] 60-80 90-110
Battery type 18,5V Li-Ion 18,5V Li-Ion
Battery capacity spec [Ah] 7.2 9.6
Power consumption [kWh/month] 8.7 11.5
Anti-theft
Bluetooth (BLE)
GSM module
Near Wire Following (MBLE)
Max altitude 3,000m 3,000m
Warranty 3 years 3 years
EN

10
RED 2014/53/EU info
These products utilize radio transmitters.
Specifications are in the table below.
Tx type Frequency Max power
BLE 2402 – 2480 MHz < 0.13 mW
GSM EGSM900 880.2 – 914.8 MHz < 0.28 W
GSM DSC1800 1710.2 – 1784.8 MHz < 0.73 W
SRD 3 – 8kHz < 73.2 dBuA/m @ 10m
LTE 1 1920 – 1980 MHz 1.86 W
LTE 3 1710 – 1785 MHz 0.64 W
LTE 8 824 – 849 MHz 0.06 W
LTE 20 832 – 862 MHz 0.66 W
LTE 28 703 – 748 MHz 0.15 W
Part Number Part Description
753-11235 Battery for XR5 1000 / 2000
753-11260 Battery for XR5 3000
753-11261 Battery for XR5 4000
122-105-603 Blade Kit
1111-M6-1008 8-Blade Kit
725-12966 Power supply for XR5 1000/2000 EU
725-12565 Power supply for XR5 3000/4000 EU
725-17184 Power supply for XR5 1000/2000/3000/4000 UK
725-17186 Power supply for XR5 1000/2000/3000/4000 CH
Replacement parts
EN

11
The products covered by this Declaration
18 Volt Battery operated Robotic Lawn Mower models: Cub Cadet XR5 1000, XR5 2000, XR5
3000, and XR5 4000 with the Base Station, with serial number dating year 2023 week 50 and
onwards. Stanley Black & Decker Outdoor GmbH declares that the products identified above
conform to the following EU Directives and their harmonized standards:
Directive 2006/42/EC - EN 60335-1:2012+AC:2014+A11:2014+A13:
2017+A1:2019+A2:2019+ A14:2019,
EN 50636-2-107:2015+A1:2018+A2:2020+A3:2021.
Directive 2014/53/EU - EN 303 447 V1.2.0 (draft),
EN 300 328 V2.2.2, EN 301 511 V12.5.1,
EN 303 413 V1.1.1, EN 301 908-1 V13.1.1
EN 301 908-13 V13.1.1, EN 62311:2008, and
Mentioned in 2014/30/EU - EN 55014-1:2017,
EN 55014-2:2015,7EN 61000-3-2:2014,
EN 61000-3-3:2013,
EN 301489-1 V2.2.3,
EN 301489-3 V2.1.1,
EN 301489-17 V3.2.4,
EN 301489-19 V2.1.1
EN 301489-52 V1.2.0.
Directive 2011/65/EU.
Directive 2012/19/EU.
The products have been developed in conformance with the following standards:
IEC 60335-1:2016 (Edition 5.2), IEC 60335-2-107:2017 (Edition 2.0)
Notified Body assessment by TUV Rheinland LGA was made for Article 3.2 of the Directive
2014/53/EU, EU-type certificate numbers RT 60173447 0001.
Product Safety Compliance Group
Stanley Black & Decker Outdoor GmbH
Wiesenstraße 9
D-66129 Saarbrücken
Signed for and on behalf of Stanley Black & Decker Outdoor GmbH:
Jason L. Zielke
VP, Robotics Engineering & Product Management
12/11/2023
EU Declaration of Conformity
EN

769-26930-00
Stanley Black & Decker Outdoor GmbH • Wiesenstraße 9 • D-66129 Saarbrücken • Germany