Cudy MC 1402 User manual
14-slot plug-in fiber optic transceiver rack
MC 1402
Model
1. Product description 3. Specification
4. Dual power backup
2. Performance characteristics
The MC1402 desktop optical transceiver rack is suitable for use in the
equipment room. It can be plugged into 1~14 pieces of 100M MC100
desktop or Gigabit MC100GS desktop. It has main backup power supply
and supports hot swap function, providing reliable and complete network
system. Efficient and economical solution.
1. Plug-in design, easy loading and unloading, plug and play, support
hot swap
2. 19′′ standard 2U rack, easy to install
3. The rack has 14 slots, which can be mixed and inserted for easy
management and maintenance.
4. All aluminum alloy casing, high shielding and strong anti-interference
ability
5. Built-in main backup power supply, low power consumption, stable
and reliable, support hot swap
6. The working status indicator is complete, the working status is clear at
a glance, and it is easy to maintain.
7. The average time between failures (MTBF) is over 100,000 hours,
which is in line with carrier-class operating standards.
8. Complete after-sales service, providing three-year quality assurance
and lifetime maintenance services
Technical Parameters
Operating temperature range: -10 ° C ~ 60 ° C
Storage temperature range: -40 ° C ~ 85 ° C
Relative humidity: 5% to 95%
Size: 482.6mm × 350mm × 88mm (length × width × height) 19 inches 2U
Power requirement
Power input: AC220V, 50~60HZ or DC48V optional
Power consumption: <60W
Single or primary backup dual power supply optional
The dual power supply and the two power supplies will supply power at
the same time, which reduces the load of each power supply and prolongs
the service life of the power supply. When one power supply fails, the
other power supply can be powered independently, so that the operation
of the transceiver is not interrupted. It is not necessary to remove the fiber
transceiver when repairing and replacing the power supply, and it is not
necessary to remove the rack from the cabinet. It is only necessary to
remove the faulty power supply from the back of the rack for repair or
replacement, which makes maintenance very convenient and quick.
5. LED Indicator light 6. LED Description
The external LED indicator of the 100/Gigabit fiber optic transceiver
supports the power supply, network connection, optical port/electrical port
working status indication, and intuitively visualizes the current system and
network status, helping engineers to analyze field problems and monitoring.
TX RX
SD
FP TP
FDX/COL
Link/ACT
1000M
PWR
Link/ACT
UTP
TX RX
SD
FP TP
FDX/COL
Link/ACT
100M
PWR
Link/ACT
UTP
LED
PWR
1000M
100M
LINK/ACT
（FP）
LINK/ACT
(TP)
FDX/COL
SD
UTP port Link/Act
status LED
UTP port duplex LED
Fiber signal status LED
Function
Power LED
UTP port speed LED
Fiber port Link/Act
statusLED
Status
ON
OFF
ON
Blink
ON
OFF
ON
OFF
ON
Blink
OFF
OFF
ON
OFF
Description
Power is ON
Power is Fail
1000M(100M) speed
100M(10M) speed
Fiber link is OK
Fiber link is fail
Link is ok
Data is been received or
transmitted
Link is fall
Full duplex
Half duplex
Fiber signal is detectd
Fiber signal is not detectd
Data is been received
or transmitted
( MC100 100M optical transceiver)
( MC100GS Gigabit Fiber Transceiver)
To avoid personal injury or damage to this product and other
products connected to it, please pay special attention to the
following safety precautions:
1. Power supply voltage. The built-in power supply is in the form
of AC220V~50/60Hz AC. Do not use it in other areas.
2. Use the appropriate power cord and power supply. You must use
the power cord supplied with this product or another qualified
power cord with a protective earth ground for the chassis; the
protective ground of the power outlet that matches the power
cord must be well grounded.
3. Pay attention to the grounding of the product. This product is
grounded through a grounding conductor in the power cord. To
avoid electric shock, the grounding conductor in the power cord
must be well connected to the ground. Before connecting the
optoelectronic ports of this product, make sure that the product is
properly grounded.
4. Be aware of the limits of all ports. To avoid fire or electric shock,
please pay attention to the fuselage of the product and all the
limits or related signs marked in this manual before connecting
this product. Use the prescribed fuse.
5. Do not take risks. When you suspect that this product is not
working properly, please consult our professional service person-
nel, do not risk to continue to operate.
6. Vibration and collision. This unit contains precision optics, so
avoid strong vibration and collision.
7. Do not open the cover or repair it without authorization. There
are no user-serviceable parts in the casing of this product. Product
maintenance can only be carried out by our company or profes-
sional maintenance personnel authorized by the company. The
user's own opening of the cover is considered to automatically
waive the product warranty right.
7. Precautions 8. Mounting Dimensions Sketch Unit (mm)
