CUE CS0409 User manual

www.cuesystem.com
Copyright © CUE, a.s., Praha, Czech Republic 1990 - 2011.
All rights reserved. Specications are subject to change without prior notice.
Page 1 of 4
DS074_01
10.11.2011
Back Box
CS0409
134,8
189
45,8
7
1
62
4
5
3
Ra 3,2
)(
Poz Číslo dílu/Název dílu Popis Materiál Počet
1 GS0034.2 krabice se svorníky Sestava_FUD 1
2
GS0032.1 úchytka zámku levá Sestava_FUD 1
3
GS0033.1 úchytka zámku pravá Sestava_FUD 1
4
M- M3 s ISO 7040 - matice pojistná 1.4301 4
5
GM0363.1 jezdec 1.4301 2
6
S- M3 x 30 kh ISO 7045 - půlkulatá křížová hlava 1.4301 2
7
M-M3 ISO - 4032 - matice obyč 1.4301 4
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED
IN THIS DRAWING IS THE SOLE
PROPERTY OF FAKTUM DESIGN
ANY REPRODUCTION IN PART OR
AS A WHOLE WITHOUT THE WRITTEN
PERMISSION OF FAKTUM DESIGN
IS PROHIBITED.
WEIGHT.: 0.443 kg
LAST CHANGE: 18.3.2011
c
b
FAKTUM DESIGN
ČERNOVICKÁ 2B
617 00 BRNO
TEL.: [phone]
WWW.FAKTUM.CZ
a
NAME: DATE: SPECIFICATION: INDEX:
CAD
A3
NAME: John CREATED: 1.5.2010
GS0038.2
DO NOT SCALE DRAWING
TITLE:
DRW. NO.:
SCALE: 1:2
SHEET 1 OF 1
MAT.: Sestava_FUD
DRAW
TOLERANCES:
ISO 2768-mK
DEBUR AND BREAK
SHARP EDGES
SURF.: 0.133 m
2
SEMI.: --
REVISION:
podomítková krabice
Dimensions
Description
Wiring knockouts
Thorns
Fixing tabs
Nuts for positioning of metal
holder with  xing tabs and
thorns (left and right)
Plasterboard wall
supports incl. screws

www.cuesystem.com
Copyright © CUE, a.s., Praha, Czech Republic 1990 - 2011.
All rights reserved. Specications are subject to change without prior notice.
Page 2 of 4
DS074_01
10.11.2011
Back Box
CS0409
Back Box Cutout
Back Box CS0409 Cutout Template
45 mm30 mm60 mm
45 mm 30 mm 60 mm
135 mm
179 mm
7 mm
touchCUE-7-B Front Panel Outline
198 x 147 mm
touchCUE-12-B Front Panel Outline
320 x 225 mm
Back Box Cutout
7 mm
7 mm

www.cuesystem.com
Copyright © CUE, a.s., Praha, Czech Republic 1990 - 2011.
All rights reserved. Specications are subject to change without prior notice.
Page 3 of 4
DS074_01
10.11.2011
Back Box
CS0409
Placing the Touch Panel into the Back Box
Hold touchpanel in the upright po-
sition and push it into the backbox
so that the thorns in the backbox
slide into the grooves in the metal
slat of the touchpanel.
This enables you to tilt the panel,
which holds in this position, and
mount cables.
If you want to place the panel in
the backbox, hold it upright and
push its bottom part strongly as
deep into the backbox as possible.
Then push the upper part of the
panel until the two metal catches
(západky – see g.xx) slide into
the xing tabs.
Step 1 Step 2
Step 3 Step 4

www.cuesystem.com
Copyright © CUE, a.s., Praha, Czech Republic 1990 - 2011.
All rights reserved. Specications are subject to change without prior notice.
Page 4 of 4
DS074_01
10.11.2011
Back Box
CS0409
Taking the Touch Panel Out
Insert a thin screwdriver into each of the two little
holes on the sides of the touch panel and push
until the metal catches get loose.
Then you can tilt the upper part of
the touch panel.
Hold the panel upright and pull its
bottom part out. In this position
you can tilt the panel to mount
cables.
If you need to remove the panel
out completely, hold it upright,
push downwards and pull it out.
Step 1 Step 2
Step 3 Step 4
Adjusting the Panel on the Wall
If the touch panel does not adhere to the wall perfectly, you can adjust it in the following way. Take the
panel out of the back box and loosen the two nuts on the metal holder on the inside of the back box (the
one with thorns and xing tabs). Then adjust the holder in a way to make the touch panel adhere neatly
to the wall.