CVTE WG13C User manual

说明书变更记录
第一次提交确认
提交后修改记录
注：说明书采用 Word 软件排版，不再使用美工软件，请工程师在此模板上编辑，编辑时注
意美观性，按照模板设定的格式排版。
提交到 PD 时请软件、硬件工程师以及审核人签字。PD 负责图片，文字间距等美观性修改。
提交到 PD 修改后，原则上不得超过两次变动，变动需要表格记录。
最后再由软件、硬件工程师以及审核人在下页签字，PD 申请料号，不做变更。
确认人员
软件工程师
硬件工程师
测试工程师
签名
郑汝权
时间
2016-05-05
修改版本
修改原因
修改摘要
负责人
时间
V1.1
V1.2
增加 FCC 警示语
郑汝权
20160621

WG13C 说明书印刷图档
备注：此页不在印刷范围内！
（本页内容工程师不需要填写）
广州视源电子科技股份有限公司
Guangzhou Shiyuan Electronics Co.,LTD .
文件图号
本页内容
WG13C 说明书
设 计
审 核
规格：145*210mm
比例：1-1

- 1 -
WG13C
User Manual
The book contains the important note and instructions for use.
Before using the product, please read the book carefully. Please keep the book safety after reading.
Catalog
1. Important information.........................................................................................- 2 -
2. Packing list............................................................................................................... - 3 -
3. Function introduction..........................................................................................- 3 -
4. Troubleshooting Methods.............................................................................. - 10 -
5. Specification .........................................................................................................- 10 -

- 2 -
1. Important information
Please read and understand all the instructions before using the product.
Damage caused by failure to comply with the instructions does not be covered under warrant.
Warning
Risk of electric shock or fire
Do not let the product and accessories contact rain or water. Do not put liquid container (such as vases) on
the product side. If the liquid flows inside the product, please immediately shut down the product and contact
customer service center.
Do not place the products and accessories near fire or other heat sources, including direct sunlight.
In the lightning weather, the product should be shut down.
Beware of short-circuited or fire！
Before the product is connected to a power supply socket, please ensure that the voltage of power
supply and products on the back or bottom printing values match. If the voltage is different, do not connect the
product to the power socket.
Beware of damage to the product！
Do not put this product or any objects on the power line or other electronic devices.
If the delivery of the products at temperature that below 5°C, please open the product packaging and waiting for
it to reach room temperature, and then connect it to the power socket for charging.
This part of the product may be made of glass. Please handle with care, so as not to hurt or damage.
Be careful of overheating！
Do not install the production in enclosed spaces. Be sure to set aside at least 4inches around the product space for
ventilation.
Cleaning products
only use the micro fiber cleaning cloth to clean the product.
Environmental protection
The product is made by recyclable and high quality materials. Do not put together the product with other living
garbage. Please understand the local classification about collecting electronic, electrical products and
battery set. The correct disposal of these products will help to avoid the potentially negative impact on the
environment and human health. This product contains the battery cannot be discarded as the
general living garbage. Please understand the local classification about collecting the provisions of battery. The
correct disposal of the battery helps to avoid the potentially negative impact on the environment and human
health.
FCC
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC RF radiation
exposure limits set forth for an uncontrolled environment.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable
exposure condition without restriction.

- 3 -
Battery
Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine,fire or the like.
Adapter
The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily
operable
Use only power supplies listed in the user instructions:
<Trade mark: undetermined >
<Model name: undetermined>
<Input: I/P:AC 100-240V 50-60Hz>
<Output: O/P:DC 18.0V,1000mA >
Only use the attachments / accessories specified by manufacturer
2. Packing list
WG13C x 1
User manual x 1
3.5mm audio cable x 1
Adapter ( 18V,1.A) x 1
3. Function introduction
Operations Guide
This product has 5 keys: Power on/off, Play/Pause, Wi-Fi, Vol+/Next and Vol-/Previous.
The function of keys:
1. Power on/off: long press for power on/off.
2. Vol+/Next and Vol-/Previous:
State
Long/Short press
Double click
Wi-Fi mode
Vol+,Vol-
Next/Previous
Line-in mode
Vol+,Vol-
NA
Bluetooth mode
Vol+,Vol-
Next/Previous

- 4 -
3. Play/Pause:
State
Short press
Wi-Fi mode & Music playing
Play / Pause
Bluetooth mode & Music playing
Play / Pause
Line-in mode& Music playing
Mute
4. Wi-Fi:
State
Long press
Wi-Fi mode
Connect the slave speaker to main speaker
Bluetooth mode
Disconnect Bluetooth
Connect adapter
standby
Close WiFi hotspot
State
Short press
Any mode
Switch to other mode
Wi-Fi speaker web setting
1. When you turn on the speaker,WiFi will automatically start.
2. After PC or smart phone connects machine through Wi-Fi(The default SSID is WG13C_XXXX, XXXX is a random
number), Customer could access the site: http://10.10.10.254 and enter the setting page. There are two tabs: Wi-Fi
and Setting.
3. Wi-Fi tab: To setup the connection between Wi-Fi speaker and AP. Customer could use PC or smart phone to
access internet through Wi-Fi speaker after connected.
4. Setting tab:
There are 3 sub tabs in setting tab: Status, System and Network.
( 1 )Status tab: Customer could view the firmware version, UUID of Wi-Fi speaker.

- 5 -
( 2 )System tab: Customer could reset the Wi-Fi speaker and local upgrade firmware in “Other” option and online
upgrade firmware in “Firmware Online Upgrade”.
( 3 )Network tab: Customer could setting the SSID, password and encryption type of Wi-Fi speaker.
Music Playing
1. Wi-Fi mode:
Customer could use APP to search WG13C and add it to the management list, then play the music that he want. If
Customer wants two speakers play the same music in the same time( Multi room mode ), Please carry out the
corresponding operation according to the APP.
Customer could automatically install the APP by Android Market or App Store. In the Android Market or App Store
search "SeewoPlayer", download and complete the installation.
2. Bluetooth mode:
（1）First power on, press the “Wi-Fi”to Bluetooth mode，the indicator light flashes (with waiting for connection
tone), please search for Bluetooth devices "WG13C” in the mobile phone or tablet PC and pair. When the pairing is
successful, the indicator light keeps on lighting.
（2）If it is need to switch to another Bluetooth terminal, long press the WiFi key, the indicator light flashes, once again
into the Bluetooth pairing state, repeat steps (1).
（ 3 ） If the Bluetooth terminal is successful paired before shutdown, the machine will automatically connect the
last successful paired terminal after next boot( do not need reconnection), the indicator light does not flash.
3. Line-in mode:
When 3.5mm audio cable is inserted into the Line-in port, machine automatically switches to Line-in mode.
4. USB charging mode:
Press the“Wi-Fi”to USB charging mode,it will charge mobile phone or other electronic devices.
Note：

- 6 -
1、If there is no signal input, such as pause playback, the product will be in 15 minutes in standby mode
2、Clear WiFi preset password, followed by five combinations of buttons:Play,Vol+,Power,Play,Power
Connecting
1. Brief introduction
（1）Open the app.
（2）Click the Icon 'Add Device', select the WIFI channel.
（3）Press the speaker "WIFI" button until the light flashes quickly.
（4）Click continue, click the link after entering the router password, wait to add equipment.
2. Adding a device connected to the router
Open the app again, it will find all devices connected.
3.How to add other non-connected devices
Connected other devices to a wireless network, please follow these steps：
step1. Click the icon '+'on the Device list.
Step2. Then add a device as the first time add same device.
Step3. After the addition,you can see the newly added device appears in the device list, as shown:
4.Renaming Devices
After adding a device, the device name can be changed according to your needs.Step as shown:
（1） Click the“Settings”button in the interface of device lists.
（2）Renameing the device : Customizing or choosing the recommended name.

- 7 -
APP functions
1.Search function
With the search function you can search for music according to your needs, either on artist or on song.
2. My favorite function
Collect your favorite songs function that allows you to choose your favorite songs.
Step 1. Click on the heart- shaped icon on the player interface, the song can be bookmarked in ”my favorite” list;
Step 2. Click go to my favorite list in the control interface and there you can see your collection of songs.
2.1 Managing Favorite Songlist
Step 1. Click on the song name on the right.
Step 2. You can choose to delete the song or add to another playlist selected from ”my favorites”list.
3. My Music - Local Music
Step 1. Click on the phone to enter the local music playlists;
Step 2. Click the icon ,which is in the upper right corner to refresh and search new songs for to add to the local playlists;
Step 3. Click the icon to the right of the song name. You can operate the songs,
”Add to Favorites”, ”Add to list” and so on.
3.2 My Music Playlist
Step 1. You can create a new list: click on the ”+“ in my music playlist;
Step 2. After entering a name click ”OK” to create a new song list.
4. Online radio station (TuneIn)
Online radio (TuneIn) provides you millions of radio stations from around the world.
（1）Click ”TuneIn” to enter the user interface.
（2）Choose the radio station you want to listen to in the list.

- 8 -
5. iHeartRadio
IHeartRadio, which is integrated in the app, is a digital broadcast & audio streaming media player that is free to use all
over the world. It includes millions of online radio stations and you can also create personalized radio stations.
6. Spotify
A better way to listen at home - Spotify Connect lets you play Spotify through your home speakers or TV, using the
Spotify app as a
remote.
You ’ ll need a Spotify Premium account to use Spotify Connect. If you don ’ t have it, just go to
http://www.spotify.com/freetrial for your
free 30-day trial.
Step 1. Connect your device to the same wi-fi network as your phone, tablet or PC running the Spotify app.
Step 2. Open the Spotify app, and play any song.
Step 3. Tap the ”song image” in the bottom left of the screen.
Step 4. Tap the ”Connect” icon
Step 5. Pick your device from the list.
For more information on how to set up and use Spotify Connect please visit www.spotify.com/connect.
7. Synchronization & separate play
Champion WH-series can play music in two or more speakers at the same time. Slide to the left and enter the device list,
you can control all the devices, such as increase/decrease the volume,select songs, sound way, etc.
In the device list, you click on the text ”How to switch between solo and Multi mode” to know more about the function
of the multiroom function.
How to update firmware WiFi
Online update：
1.Turn on the speaker，change it into wifi mode, after it prompt wifi network ready voice, use PC to connect the wifi
signal of speaker.
2.Enter “10.10.10.254”in the browser of PC.

- 9 -
3.Connected network
4.Then select “Setting”
5.lick “System”
6.lick “online Update”
7.It will automatically download firmware upgrades,when it’s upgraded successfully, the web will show a message.
APP update：
If you see “New” icon next to setting button, a new firmware is available for your unit. In order to apply this
firmware tap on “New” and you will see a pop up message. Plug in adapter, then select upgrade and wait until the
device upgrade process finishes without other operations .
Interface icon and functions
How to clean the machine
Warning：
1. Turn off machine before cleaning it.
2. Do not use volatile solvents (such as ethanol, rosin, toluene solvent) to clean the machine. This type of chemicals may
damage the machine.

- 10 -
3. Use cotton or microfiber cleaning cloth.
4. In the cleaning process, do not water droplets into the product panels and speakers causing malfunction.
4. Troubleshooting Methods
The following table contains common problems and solutions, please read carefully.
5. Specification
Model
WG13C
speaker
1x 3 inch woofer, 8ohm
Frequency response
90Hz-20KHz (-10dB)
Power amplifier
Class D @ 15W × 1CH
THD
< 10%
SNR
≧75dB(A)
Play mode
Wi-Fi/Bluetooth/Line-in
Adapter
DC 18V,1A
Battery
1300mAh/11.1V
Standby power
Networked standby＜2.5W
Close WifI hotspot＜0.5W
Product size
198x115x164.5mm
WI-Fi
Support 802.11 b/g/n
Support STA/AP/AP Client
Problem
Solution
The speaker has no sound
Make sure the machine was charged before used;
Try to increase the volume;
Please reselect the audio input channel;
Please make sure that all cables are correctly connected;
The speaker murmur
Please make sure that all cables are correctly connected;
Please replace the other audio cable;
Please ensure the equipment that connected audio cable
output itself did not murmur;
No power or No charging
Please make sure that the adapter and the host is connected
correctly;
Please check the power adapter voltage and current
demand;
Wi-Fi mode without sound
Please check whether the PC or smart phone and machine
are in the same Lan or not;
Please check whether the machine is in Wi-Fi mode or not;
If using the app, please check whether the music is sent to
the speaker or not;
Line-in mode without sound
Please check whether the audio cable is properly connected
or not;
The keys have no function
Plug the adapter, then power on;
Use a toothpick or needle to press the reset hole, then
power on;