Cybernet H24 Series User manual

LCD-PC H24 Series
User Guide

i
FCC-B Radio Frequency Interference Statement
This equipment has been tested and found to comply with
the limits for a class B digital device, pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the
measures listed below.
•Reorient or relocate the receiving antenna.
•Increase the distance between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/television technician for help.
Notice 1 The changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Notice 2 Shielded interface cables and A.C. power cord, if any, must be used in order
to comply with the emission limits.
Trademarks
All trademarks are the properties of their respective owners.
Intel® is a registered trademarks of Intel Corporation.
Windows® 7/Vista/XP/NT/2000/98/95 are registered trademarks of Microsoft Corporation.
Award® is a registered trademark of Phoenix Technologies Ltd.
AMI® is a registered trademark of American Megatrends Inc

ii
Safety Instructions
1. Always read the safety instructions carefully.
2. Keep this equipment away from humidity.
3. Lay this equipment on a reliable flat surface before setting it up.
4. The openings on the enclosure are for air convection hence protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
5. Confirm the voltage of the power source and adjust accordingly to 110/220V
before connecting the equipment to the power inlet.
6. Place the power cord in such a way that it cannot be stepped on. Do not
place anything over the power cord.
7. Always unplug the Power Cord before inserting any add-on card or module.
8. All cautions and warnings on the equipment should be noted.
9. Never pour any liquid into the opening. This will cause damage and/or electrical
shock.
10. Do not disable the protective grounding pin from the plug. The equipment must be
connected to a grounded main socket/outlet.
11. The Optical Storage devices are classified as Class 1 Laser products. Use of
controls or adjustments or performance of procedures other than those specified is
prohibited.
12. Do not touch the Laser lens inside the optical storage drive.
13. When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the
metal shield is reliably connected to a protective earthing system of the building.
Cable distribution systems should be grounded (earthed) in accordance with
ANSI/NF PA 70, the National Electrical Code (NEC ), in particular, Section 820.93,
Grounding of Outer Conductive Shield of a Coaxial Cable.
14. If any of the following situations arise, have the equipment checked by authorized
service personnel:
•The power cord or plug is damaged.
•Liquid has penetrated into the equipment.
•The equipment has been exposed to moisture.
•The equipment has not worked well or you cannot get it working according to
the User's Guide.
•The equipment has been dropped and damaged.
•The equipment has obvious signs of breakage.
15. Do not attempt to remove or upgrade any component by yourself, any installation or
modification should be conducted by service personnel.
DO NOT LEAVE THIS EQUIPMENT IN AN UNCONDITIONED ENVIRONMENT WITH A
STORAGE TEMPERATURE ABOVE 50° C (122°F). IT MAY DAMAGE THE
EQUIPMENT.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type recommended by the manufacturer.

iii
WEEE Statement
(Waste Electrical and Electronic Equipment)
The WEEE directive places an obligation on EU-based manufacturers, distributors,
retailers and importers to take-back electronics products at the end of their useful life. A
sister Directive, ROHS (Restriction of Hazardous Substances) compliments the WEEE
Directive by banning the presence of specific hazardous substances in the products at the
design phase. The WEEE Directive covers products imported into the EU as of August 13,
2005. EU-based manufacturers, distributors, retailers and importers are obliged to finance
the costs of recovery from municipal collection points, reuse, and recycling of specified
percentages per the WEEE requirements.
Instructions for disposal of WEEE by Users in the European Union
The symbol shown below is on the product or on its packaging, which indicates that this
product must not be disposed of with other waste. Instead, it is the user’s responsibility to
dispose of their waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service
or where you purchased the product.

iv
TABLE OF CONTENTS
FCC-B Radio Frequency Interference Statement......................................................................i
Trademarks...................................................................................................................................i
Safety Instructions......................................................................................................................ii
WEEE Statement........................................................................................................................iii
Introduction.................................................................................................................................1
LCD-PC H24 Series (H8) Specifications....................................................................................1
Processor Support ..................................................................................................................1
Motherboard Core Logic........................................................................................................ 1
Memory Support......................................................................................................................1
Networking...............................................................................................................................1
Audio.........................................................................................................................................1
Hard Disk Drive........................................................................................................................2
Mounting...................................................................................................................................2
LCD Panel.................................................................................................................................2
Expansion Slots.......................................................................................................................2
Front Lower Right Bezel .........................................................................................................2
Right Side Bezel.......................................................................................................................2
Left Side Bezel.........................................................................................................................2
Bottom I/O Panel.....................................................................................................................3
Power Supply...........................................................................................................................3
Dimensions ..............................................................................................................................3
Power Management....................................................................................................................8
Waking the System Up..........................................................................................................10
Energy Saving Tips ...............................................................................................................10
H24 Series Overview……...…………..…………………………………...…………………………11
On Screen Display Buttons………………………………………………………………………….14
On Screen Display Usage.....................................................................................................15
System Assembly.....................................................................................................................20
Necessary Tools................................................................................................................... 20
Orientation of Key Parts........................................................................................................21
H24 Series Disassembly .......................................................................................................22
Installing the CPU..................................................................................................................24
Installing the CPU Heat Sink.................................................................................................25

v
Installing the Memory Module DDR3 SO-DIMM ..................................................................26
Installing the Hard Disk Drive...............................................................................................27
Installing the Optical Disk Drive...........................................................................................28
Installing the Mini-PCIe Card (Optional)..............................................................................30
Installing the Cover ...............................................................................................................31
Cybernet Recycling SOP…………………………………………………………………………….33
Figures
Figure 1: Front View with Optional Webcam………….…………………………….....……..……11
Figure 2: Left side view with Optical Drive……………………………………………....…..…….12
Figure 3: Side USB Ports………………….………………………………………………......………13
Figure 4: Touch Panel and Power Button………..……..………………..……………….....……..13
Figure 5: On Screen Display Buttons .....................................................................................14
Figure 6: On Screen Display Icons on H8 Main board…..…………..…………….…..………...15
Figure 7: Back view ..................................................................................................................18
Figure 8: Bottom Panel I/O Ports.............................................................................................18
Figure 9: Ctrl+Alt+Del button...................................................................................................19
Figure 10: CPU Heat Sink Ventilation Fan..............................................................................19
Figure 11: System Fans, CPU Heat Sink Fan and Ventilation...............................................21
Figure 12: Open system..........................................................................................................23
Figure 13: Open system with GPU.........................................................................................23

H24 Series
Page 1
Introduction
Congratulations for purchasing the H24 Series. The LCD-PC H24 Series is your best
Slim LCD PC choice. With the fantastic appearance and small form factor, it can easily
be set anywhere. The feature packed platform also gives you an exciting PC experience.
H24 Series (H8) Specifications
Processor Support
4th generation Intel® Core™ i3 i5 and Core™ i7 in the LGA1150 package up to 35W
(Max 65W for IGD version).
Motherboard Core Logic
Intel® H81 Express chipset (Haswell)
Memory Support
DDR3 1333/1600 MHz SO-DIMM SDRAM (Un-buffered Non-ECC)
2DDR3 1333/1600 MHz SO-DIMM slots (8GB Max) with 1.5V.
Video & Graphics
Intel® integrated H81 Chipset with Intel® HD Graphics
Intel GMA HD/Intel Clear Video HD Technology
Built-in support for 1080p HD video playback, HDMI 1.4 & Blu-ray 3D support
Supports Microsoft®DirectX 11.1, OpenCL 1.2 and OpenGL 4.0.
DVMT allocated as needed from 128MB to 1.70GB
Maximum display resolution 2560 x 1600.
Video & Graphics for dedicate Nvidia GPU
Onboard NVIDIA GeForce N14M-GE GPU
2.0GB sDDR3 128-bit RAM
1080p HD video playback, HDMI 1.4 & Blu-ray 3D support.
Supports Microsoft® DirectX 11, Shader Model 5.0 and OpenGL 4.1
Maximum display resolution 2560 x 1600.
Networking
Supports 2 PCI Express LAN 10/100/1000 Fast Ethernet by Intel I217V Clarkville-V and
Realtek RTL8111G
Audio
2 internal speakers with 78dB+/-3dB @ 2.0W
HD Audio Codec Realtek® ALC892 Flexible 10-channel audio with jack sensing,
Compliant with Azalia 1.0 Spec

H24 Series
Page 2
Hard Disk Drive
Optional two 2.5” SATA III Hard Disk Drive or SATA SSD - Any Capacity
RFID Reader
Optional one 125KHz or one 13.56MHz.
Wall Mount
Support 75x75mm / 100x100mm VESA mounting hole, using M4 screw. The 75x75mm
can support max screw length of 12mm; and 100x100mm can support max screw length
of 16mm.
Swivel Stand
System Base enables left/right rotation up to 60 degrees, tilt from -5 to 60 degrees.
LCD Panel
23.6" LED widescreen 16:9 format display (1920x1080).
Optional Touch Screen
Ten-finger Multi-touch P-cap solution.
Webcam
Optional 3.0 Megapixel Camera
Expansion Slots
Two mini-PCIe (One full size and one half size)
Wireless
Optional 802.11 b/g/n + Bluetooth or 802.11 a/b/g/n + Bluetooth
Front Lower Right Bezel
Power On/Off Buttons
Display On/Off Adjust and also function as Menu Button
Contrast Adjust
Brightness Adjust
Right Side Bezel
Two USB 2.0 ports (for mouse and keyboard)
Left Side Bezel
Optional one optical tray type disk drive – 2.5” slim or optional one additional 2.5” SATAII
HDD/SSD.

H24 Series
Page 3
Bottom I/O Panel
1 Ctrl+Alt+Del button
1 DC/IN port, 1 HDMI-OUT port, 1 DP port
2 USB2.0 ports, 2 USB3.0 ports, 1 Serial port, 1 CMOS clear button, 1 1394 port, 1
HDMI-IN port, 1 Realtek LAN port, 1 Intel LAN port, 3 Audio jacks – Line in, Line Out and
Mic in
4 TV Tuner ports - Optional with TV Tuner (COAX Cable In, RCA Composite Video In,
Audio Left & Audio Right),
Power Supply
120 Watt Power Adapter, AC Input: 100~240V AC, 2A, 50-60Hz
DC Output: 19V, 6.32A or 12V, 10.00A 120W Max.
Internal Battery
Optional battery to last 20 mins depending on system usage/loading.
Dimensions
598mm (H) x 420mm (W) x 262 mm (D) (with stand)
598mm (H) x 377mm (W) x 55 mm (D) (without stand)

H24 Series
Page 4
Intended use
The H24 Series is designed for general pc application purpose for hospital environment
and for diagnosis. It could be used for Radiology, PACS (Picture Archiving
Communication Systems), LIS (Lab Information Systems) and Electronic Record
purpose. It shall not be used for life-supporting system.
WARNING: Critical diagnostic decision must not be based solely on images displayed by
this device.
Unpacking
After opening the carton, there is the LCD PC with an accessory box. Check carefully to
see if there are any damages or missing parts.
Read the Manual
Please read this manual carefully and remember to keep this manual for future reference.
Safety Instructions & Cleaning
This product has undergone various tests in order to comply with safety standards.
Inappropriate use or open the housing may be dangerous. Please remember to follow the
instructions below to ensure your safety during the installation and operating process.
Transporting & Placement of unit
1. When moving the unit on a cart; be very cautious. Quick stops, excessive forces and
uneven surfaces may cause the cart to overturn thus risking the unit to fall to the
ground.
2. If the LCD PC unit does fall to the ground, immediately turn the power off and
disconnect cords. Then contact a service technician for repairs. Continual use of
the unit may result cause a fire or electric shock. Also, do not repair the unit on your own.
3. Having two or more people transporting the LCD PC unit is recommended. In addition,
when installing the unit by suspending it also requires two or more people.
4. Before suspending the unit, make sure the material used for suspension is sturdy and
stable. If not properly suspended, the LCD PC unit may fall and cause serious injury to
people standing nearby as well as to the unit itself.
5. If the user wishes to mount the LCD PC unit, remember to use only the mounting
hardware recommended by the manufacturer.

H24 Series
Page 5
Electrical and Power Source Related
1. This LCD PC unit must operate on a power source as shown on the specification label.
If you are not sure what type of power supply used in the area, consult your dealer or local
power supplier.
2. The power cords must not be damaged. Applied pressure, added heat, and tugging
may damage the power cord.
3. The power cord must be routed properly when setup takes place. We advise that this
aspect measure is to prevent people from stepping on the cords or while the unit is
suspended to prevent flying objects from getting tangled with the unit.
4. Do not overload the AC outlets or extension cords. Electrical shocks or fires may occur
from overloading.
5. Do not touch the power source during a thunderstorm.
6. If your hands are wet, do not touch the plug.
7. Use your thumb and index finger, grip firmly on the power cord to disconnect from the
electrical socket. By pulling the power cord, may result in damaging it.
8. If the unit is not going to be in use for an extended period of time, remember to
disconnect the unit.
9. The LCD PC unit uses 19V DC output from an adapter. Connect the unit to a power
source with the same numerical value as indicated. Please use only the power cord
provided by the dealer to ensure safety and EMC compliance.
WARNING:To avoid risk of electric shock, this equipment must only be connected to a
supply mains with protective earth.
Various Factors of Environment
1. Operating Temperature: 0°C to 40°C ; Non-operating temperature: -20°C to 60°C.
2. Operating Humidity (Non-Condensing): 10% to 90%. Non-operating Humidity
(Non-condensing): 10% to 90%.
3.Do not insert objects into the openings.
4. Do not have liquids seep into the internal areas of the LCD PC unit.
5. Having liquids seep in or inserting objects into the unit may result in electric shocks

H24 Series
Page 6
from taking and/or short circuiting the internal parts.
6. Do not place the LCD PC unit in the presence of high moisture areas.
7. Do not install the LCD PC unit in a wet environment.
8. Do not place unit near heat generating sources.
9. Do not place the unit in a location where it will come in contact with fumes or steam.
10. Remember to keep the LCD PC unit away from the presence of dust.
11. If water has flow in or seep in, immediately disconnect the open frame unit. Then
contact a service technician for repairs.
Ventilation Spacing
1. Do not cover or block the openings on the top and back sides of the LCD PC unit.
Inadequate ventilation may cause overheating thus reducing the lifespan of the unit.
2. Unless proper ventilation is present, do not place unit in an enclosed area; such as a
built-in shelf. Keep a minimum distance of 10 cm between the LCD PC unit and wall.
Cleaning the unit
1. Remember to turn off the power source and to unplug the cord from the outlet before
cleaning the unit.
2. Carefully dismount the unit or bring the unit down from suspension to clean.
3. Please use a dry soft cloth to clean the unit.
4. Take a dry cloth and wipe the unit dry. Remember to avoid having liquids seep into the
internal components and areas of the LCD PC unit.
Servicing, Repairing, Maintenance & Safety Checks
1. If the unit is not functioning properly, observe the performance level of the LCD PC
closely to determine what type of servicing is needed.
2. Do not attempt to repair the LCD PC unit on your own. Disassembling the cover
exposes users’ to high voltages and other dangerous conditions. Notify and request a
qualified service technician for servicing the unit.
3. To avoid risk of electric shock, this equipment must only be connected to a supply
mains with protective earth.

H24 Series
Page 7
4. If any of the following situations occur turn the power source off and unplug the unit.
Then contact a qualified service technician.
(a) A liquid was spilled on the unit or objects have fallen into the unit.
(b) The unit is soaked with liquids.
(c) The unit is dropped or damaged.
(d) If smoke or strange odor is flowing out of the operating unit.
(e) If the power cord or plug is damaged.
(f) When the functions of the unit are dysfunctional.
5. When replacement parts are needed for the LCD PC unit, make sure service
technicians use replacement parts specified by the manufacturer, or those with the same
characteristics and performance as the original parts. If unauthorized parts are used it
may result in starting a fire, electrical shock and/or other dangers.
ISO 7000-0434: Caution, consult ACCOMPANYING DOCUMENTS.
ISO 7000-1641: Follow operating instructions or Consult instructions
for use.
IEC 60417 -5009: ready to use.
IEC 60417-5031: Direct current.
EU-wide legislation, as implemented in each Member State, requires
that waste electrical and electronic products carrying the mark (left)
must be disposed of separately from normal household waste. This
includes monitors and electrical accessories, such as signal cables or
power cords. When you need to dispose of your panel PC products,
please follow the guidance of your local authority, or ask the shop
where you purchased the product, or if applicable, follow any
agreements made between yourself. The mark on electrical and
electronic products only applies to the current European Union
Member States.

H24 Series
Page 8
Power Management
Power management of LCD-PC has the potential to save significant amounts of electricity
as well as deliver environment benefits.
To be energy efficient, turn off your display or set your LCD-PC to sleep mode after a
period of user inactivity.
Power Management in Windows OS
[Power Options] in Windows OS allow you to control the power management features of
your display and hard drive. Go to [Start] > [Control Panel].
Then click on the [Power Options] link.

H24 Series
Page 9
Select a power plan that suits your personal needs. You may also fine-tune the settings
by clicking [Change plan settings].
The Shut Down LCD-PC Menu presents the options of Sleep (S3) & Shut Down (S5) for
rapid and easy management of your system power.

H24 Series
Page 10
Power Management through ENERGY STAR qualified Monitors (Not
supply with the LCD PC)
The power management feature allows the LCD-PC to initiate a low-power or “Sleep”
mode after a period of user inactivity. When used with an external ENERGY STAR
qualified Monitor, this feature also supports similar power management features of the
monitor. To take advantage of these potential energy saving, the power management
feature can be set to behave in the following ways when the system is operating on AC
power:
•Turn off the display after 15 minutes.
•Initiate Sleep after 30 minutes.
Waking the System Up
The LCD-PC shall be able to wake up from power saving mode in response to a
command from any of the following:
•the power button,
•the network (Wake on LAN),
•the mouse
•the keyboard
Energy Saving Tips:
•Tune the settings in Power Options under Windows OS to optimize your LCD-PC’s
power management.
•Install power saving software to manage your PC’s energy consumption.
•Always disconnect the AC power cord or switch the wall socket off if your LCD-PC
would be left unused for a certain time to achieve zero energy consumption.

H24 Series
Page 11
LCD-PC H24 Series Overview
Figure 1: Front View with Optional Webcam

H24 Series
Page 12
Figure 2: Left side view with Optical Drive

H24 Series
Page 13
Figure 3: Side USB Ports
Figure 4: Touch Panel and Power button
ready to use button”

H24 Series
Page 14
On Screen Display Buttons
Figure 5: On Screen Display Buttons
There are four buttons on the lower bezel of the screen. From right to left they are:
OSD key Response time Function
Ready to use Delay 1.5 sec On/off Power
Menu
button/Privacy
button
immediately
Firstly enter into Menu; Secondly to confirm.
When turn off the privacy button- it will Turn
off the Touch function as well.
When turn on the privacy button, it will turn on
the Touch function and also wake up the unit
from sleep mode as well
Contrast / + Immediately
Turn on the contrast adjustment on display
Continuous send out pulse when user’s finge
r
keep pressing the button and increase the
value
Brightness / - Immediately
Turn on the brightness adjustment on display
Continuous send out pulse when user’s finge
r
keep pressing the button and increase the
value