d & b audiotechnik Z5330.050 User manual

DZ5330.050
Manual 1.1 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
Z5330.050 Manual
Version: 1.1 en, 07/2014, D2023.EN .01
Copyright © 2014 by d&b audiotechnik GmbH; all rights
reserved.
Keep this manual with the product or in a safe place
so that it is available for future reference.
We recommend you to regularly check the d&b website for the
latest version of this manual.
When reselling this product, hand over this manual to the new
customer.
If you supply d&b products, please draw the attention of your
customers to this manual. Enclose the relevant manuals with the
systems. If you require additional manuals for this purpose, you
can order them from d&b.
d&b audiotechnik GmbH
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

1. Z5330.050 D80 Touring rack assembly -
NEMA L21-30.................................................................... 4
1.1. Intended use................................................................ 4
1.2. Scope of supply........................................................... 4
2. Handling, cooling and placement............................ 5
2.1. Handling...................................................................... 5
2.2. Cooling and placement.............................................. 5
3. X5336 Mains power distributor -
NEMA L21-30.................................................................... 6
3.1. Intended use................................................................ 6
3.2. Rear panel................................................................... 6
3.2.1. AMP 1 / AMP 2 / AMP 3...................................... 6
3.2.2. MAINS SUPPLY....................................................... 7
3.3. Front panel................................................................... 7
3.3.1. MAINS..................................................................... 7
3.3.2. AUXILIARY MAINS OUTPUTS 16 A...................... 7
3.3.3. 4 CH OUTPUTS - NL8............................................. 8
3.3.4. 6 CH OUTPUTS6 CH OUTPUTS - LKS 19 F.......... 8
3.3.5. NL8 F / LKS 19 F - Pin assignments........................ 9
4. Z5338 I/O Panel........................................................... 10
4.1. INPUT........................................................................ 10
4.2. INPUT LINK............................................................... 10
4.3. REMOTE.................................................................... 10
5. Z5333 Rack link............................................................ 12
6. Manufacturer's Declaration..................................... 13
Contents
d&b Z5330.050 Manual 1.1 en 3

1.1. Intended use
The Z5330.050 D80 Touring rack assembly is designed as a
closed system rack providing mains power distribution and
connector interfaces for 3 x D80 amplifiers. For this purpose, the
touring rack is equipped with a mains power distribution device
(X5336), which also serves as a loudspeaker connector panel.
Also incorporated is an I/O panel (Z5338), which serves as a
connector interface for both analog and digital audio signals. In
addition, four network connectors are provided for either Ethernet
or CAN-Bus remote capabilities.
1.2. Scope of supply
Before starting up, please verify the shipment for completeness and
proper condition of the items.
If there is any sign of obvious damage, do not operate the rack
assembly and contact your local dealer from whom you received
it.
Pos. Qty. d&b Code Description
[1] 1 Z5330.050 Touring rack assembly
NEMA L21-30 - with shock
mounted 19" frame.
Including:
[2] 1 X5336 Mains power distribution (NEMA
L21-30) and LS panel.
[3] 3 Z2710 D80 Amplifier
[4] 1 Z5338 I/O Panel
[5] 1 Rack drawer 1RU.
[6] 1 Z5333 Rack link (contained in the rack
drawer [5]).
Dimensions and weight
Height x width x depth 710 x 600 x 780 mm
28 x 23.6 x 30.7"
Total weight 128 kg / 282 lb
[1]
[2]
[3]
[4]
[5]
[6]
1. Z5330.050 D80 Touring rack assembly - NEMA L21-30
d&b Z5330.050 Manual 1.1 en4

2.1. Handling
The touring rack is equipped with two sliding doors allowing quick
and easy access to the front and rear panels of the devices.
1. Unlock the door lock mechanism.
2. Open the door and ...
3. push the door to the rear into its park position.
2.2. Cooling and placement
When using the d&b Z5330 D80 Touring rack assembly, make
sure to provide sufficient space of 0.5 m (1.6 ft) at the front and
rear of the touring rack to ensure sufficient cooling airflow.
D80 Touring rack assemblies can be positioned side by side or
stacked.
When combining the Z5330 D80 Touring rack assembly with the
Z5310 D12 Touring rack assembly or any other rack assembly
that produces an opposing airflow, observe the following
restrictions:
– D12/D80 Touring rack assemblies can be positioned side by
side.
– Do not stack D80 and D12 Touring racks or any other rack
assemblies with opposing airflow.
2. Handling, cooling and placement
d&b Z5330.050 Manual 1.1 en 5

X5336 Front panel
3.1. Intended use
The X5336 Mains power distributor is designed and dimensioned
to provide and distribute the mains power supply necessary for the
three D80 amplifiers. It also serves as a loudspeaker connection
panel for different connection options. It is a protective class 1 unit
with IP class 20 (NOT rain-, drip-, or splash-proof!).
The X5336 Mains power distributor must not be used for any other
purpose or outside the system rack.
WARNING!
Potential risk of electric shock.
The mains power distributor is a protective class 1 unit. A missing
earth (ground) contact may cause dangerous voltages in the
housing and controls and may lead to electric shock.
– Connect the unit to mains power supplies with protective earth
only.
– If there is any sign of obvious damage to the power cord
and/or NEMA mains connector, do not use the unit and
replace it before further use.
– Please ensure the mains connector is accessible at any time to
disconnect the unit in case of malfunction or danger.
– Do not connect or disconnect the NEMA mains connector
under load or live.
3.2. Rear panel
3.2.1. AMP 1 / AMP 2 / AMP 3
Three fixed single-phase mains power lines (L1-L2-L3, Y-wired,
120 V), each fitted with a powerCON-HC® mains connector, are
provided for the internal mains power supply of the amplifiers.
NOTICE!
The mains power distributor device has no built-in circuit-breaker
for the amplifier's mains power lines. Protection is provided by the
onsite sub-distribution.
X5336 Rear panel
3. X5336 Mains power distributor - NEMA L21-30
d&b Z5330.050 Manual 1.1 en6

3.2.2. MAINS SUPPLY
Required mains supply network configuration
3-phase 120 V plus neutral, ~ 60 Hz - 30 Amax.
The X5336 Mains power distributor is supplied with a fixed 3-
phase power cord equipped with a 30 A NEMA L21-30 mains
connector.
3.3. Front panel
3.3.1. MAINS
When the rack is connected to the onsite mains power supply, the
three mains indicators display the presence of the onsite mains
supply lines (phase conductor L1-L2-L3).
3.3.2. AUXILIARY MAINS OUTPUTS 16 A
Three auxiliary mains outputs (powerCON sockets) are provided.
One socket is mounted on the front and two sockets on the rear
panel. They are intended for the connection of low current devices
such as notebooks or additional Ethernet switches.
Each socket can be switched on and off by its dedicated switch.
These switches also serve as circuit-breakers for the corresponding
socket.
Please refer to the switch assignment as shown in the graphic
opposite.
d&b Z5330.050 Manual 1.1 en 7

3.3.3. 4 CH OUTPUTS - NL8
NOTICE!
The 4 CH OUTPUTS connectors are only intended as an interface
to a rack panel or to loudspeaker multicores such as d&b
Z5343.xxx and breakout adapters such as d&b Z5347.xxx.
Do not connect any loudspeaker cabinets, neither passive nor
active systems, to the 4 CH OUTPUTS connectors, otherwise there
is a risk of damaging the loudspeaker components or the amplifier.
Each of the 4 CH OUTPUTS connectors represents the 4
CHANNEL OUTPUT of the respective D80 amplifier. Each
connector carries the output signals of all four channels of the
amplifier with the following pin assignment.
1+/— = Channel A pos. / neg. 2+/— = Channel B pos. / neg.
3+/— = Channel C pos. / neg. 4+/— = Channel D pos. / neg.
Please refer to the corresponding channel assignment label above
each connector as shown in the graphic opposite.
3.3.4. 6 CH OUTPUTS6 CH OUTPUTS - LKS 19 F
The 6 CH OUTPUTS multipin connectors (LKS 19) are used in
connection with the d&b Z5320.xxx cabling system to allow
efficient system wiring using loudspeaker multicore cables.
Each connector carries the output signal of six amplifier channels.
Please refer to the corresponding channel assignment label above
each connector as shown in the graphic opposite.
d&b Z5330.050 Manual 1.1 en8

3.3.5. NL8 F / LKS 19 F - Pin assignments
4 CH OUTPUTS 6 CH OUTPUTS
NL8 F LKS 19 F - 1 Section Pin # LKS Pin-out - Front view
AMP 1
CH A/B/C/D
CH A: 1+
CH A: 1—
AMP 1
CH A/B/C/D
1
6
L
N
CH B: 2 +
CH B: 2 —
1
6
GND
GND
CH C: 3 +
CH C: 3 —
2
1
L
N
CH D: 4 +
CH D: 4 —
3
2
L
N
AMP 2
CH A/B/C/D
CH A: 1+
CH A: 1— AMP 2
CH A/B
3
4
N
L
CH B: 2 +
CH B: 2 —
3
4
GND
GND
LKS 19 F - 2 Section Pin # LKS Pin-out - Solder side
CH C: 3 +
CH C: 3 — AMP 2
CH C/D
1
6
L
N
CH D: 4 +
CH D: 4 —
1
6
GND
GND
AMP 3
CH A/B/C/D
CH A: 1+
CH A: 1—
AMP 3
CH A/B/C/D
2
1
L
N
CH B: 2 +
CH B: 2 —
3
2
L
N
CH C: 3 +
CH C: 3 —
3
4
N
L
CH D: 4 +
CH D: 4 —
3
4
GND
GND
d&b Z5330.050 Manual 1.1 en 9

4.1. INPUT
The INPUT section represents the input connectors of the first
amplifier while the other two amplifiers are linked within the rack.
The INPUT section allows both analog and digital audio signals to
be fed to the amplifier.
4.2. INPUT LINK
The INPUT LINK section represents the link output connectors of the
last (third) amplifier and allows the linking of further system racks
using the enclosed rack link cable (Z5333 Rack link).
4.3. REMOTE
The REMOTE section allows the daisy chaining of system racks
within a remote network using the enclosed rack link cable (Z5333
Rack link).
Ethernet network
ETH 1 Represents the upper etherCON connector of the first
amplifier and may be used as input while the other two
amplifiers are linked within the rack.
ETH 2 Represents the bottom etherCON connector of the last
(third) amplifier and may be used as output.
Note: In a daisy chain topology, if one device or an entire
rack fails or is switched off, this also affects all subsequent
devices and/or system racks which are then no longer
connected to the network either.
A detailed description of remote control via Ethernet is given in
the technical information TI 310 (d&b code D5310.EN) which
can be downloaded from the d&b website at
www.dbaudio.com.
4. Z5338 I/O Panel
d&b Z5330.050 Manual 1.1 en10

CAN-Bus network
CAN Represents the CAN input of the first amplifier
while the other two amplifiers are linked
within the rack.
CAN LINK Represents the CAN output of the last (third)
amplifier.
TERMINATE/
LINK
The built-in termination switch allows two
settings:
1. LINK: In system racks, at the start of and
within a CAN-Bus segment, set the switch
to LINK.
2. TERMINATE: On the last system rack of
a CAN-Bus segment, set the switch to
TERMINATE
Note: A detailed description of remote control via the d&b
Remote network (CAN-Bus) is given in the technical
information TI 312 (d&b code D5312.EN) which can be
downloaded from the d&b website at www.dbaudio.com.
d&b Z5330.050 Manual 1.1 en 11

The rack link cable allows further system racks to be linked
together.
It is suitable for both analog and digital audio signals as well as
for network wiring (Ethernet or CAN-Bus networks).
Technical specifications
Audio connector 2 x XLR female to 2 x XLR male
with color markup
Audio signal capability Analog
Digital AES/EBU (AES 3)
Network connector etherCON
Network cable CAT 5E SFTP
Length 2 m / 6.5 ft
Rack link example:
4ch Digital audio and CAN-Bus
Rack link example:
2ch Analog audio and CAN-Bus
5. Z5333 Rack link
d&b Z5330.050 Manual 1.1 en12

This declaration applies to:
d&b Mains power distributor NEMA L21-30,
X5336.000
manufactured by d&b audiotechnik GmbH.
All products of type X5336.000 are included, provided they
correspond to the original technical version and have not been
subject to any later design or electromechanical modifications.
We herewith declare that said products are designed and tested in
conformity with the provisions of the respective IEC 60065
directive including all applicable amendments.
– EN 60065:2002
d&b audiotechnik GmbH of Backnang accepts responsibility for
this declaration.
Backnang, 2014-05-19
Frank Bothe,
Head of R&D
d&b audiotechnik GmbH
6. Manufacturer's Declaration
d&b Z5330.050 Manual 1.1 en 13

D2023.EN .01, 07/2014 © d&b audiotechnik GmbH
www.dbaudio.com