d & b audiotechnik SL Series Quick start guide

SLE7494
Rigging manual 1.3 en

S
y
m
b
o
l
s
o
n
t
h
e
p
r
o
d
u
c
t
P
l
e
a
s
e
r
e
f
e
r
t
o
t
h
e
i
n
f
o
r
m
a
t
i
o
n
i
n
t
h
e
m
a
n
u
a
l
.
W
A
R
N
I
N
G
!
D
a
n
g
e
r
o
u
s
v
o
l
t
a
g
e
!
General information
E7494 Rigging manual
Version: 1.3 en, 10/2020, D2736.EN .01
Copyright © 2020 by d&b audiotechnik GmbH & Co. KG; all
rights reserved.
Keep this document with the product or in a safe place
so that it is available for future reference.
We recommend you to regularly check the d&b website for the
latest version of this document.
When reselling this product, hand over this document to the new
owner.
If you supply d&b products, please draw the attention of your
customers to this document. Enclose the relevant documents with
the systems. If you require additional documents for this purpose,
you can order them from d&b.
d&b audiotechnik GmbH & Co. KG
Eugen-Adolff-Str. 134, D-71522 Backnang, Germany
T [phone], F [phone]
[email protected], www.dbaudio.com

E7494 SL Outriggers
1.1 Intended use
WARNING!
Potential risk of personal injury and/or
damage to material!
Always secure ground stacked setups against movement and
possible tipping over.
Observe the maximum number of cabinets permitted.
In connection with SL-Series ground stacks consisting of GSL8/
GSL12 or KSL8/KSL12 cabinets, the E7494 SL Outriggers are
used to provide an adequate and stable ground support. Two rods
with winder are provided to adjust the vertical inclination of the
entire ground stack.
For this purpose, the corresponding touring carts are equipped
with corresponding slots at the bottom of each corner.
Once the stack is placed in its operating position, the outriggers
have to be attached to the cart.
Note: For ground stack setups, please refer to the SL-Series
Rigging manual.
1.2 Scope of supply
Please verify the shipment for completeness and proper condition
of the items.
The E7494 SL Outriggers are equipped and supplied with the
following components:
Pos. Qty. Description
[1] 2 Winder base.
[2] 2 Detachable winder base crank.
[3] 2 Outrig pole for winder base.
[4] 2 Outrig pole with fixed base.
[5] 10 Socket pin (12 x 50 mm).
[6] 10 Steel wire rope to be attached to the Socket
pins.
[7] 10 Torx T20 screw (M4 x 8 mm - self-tapping) to
fix the steel wire ropes to the corresponding
hole positions of the outrig pole for winder
base and Touring cart.
1 E7494 SL Outriggers
d&b E7494 Rigging manual 1.3 en 3

Preparations and application
Attaching and fixing the steel wire ropes
To prevent the Socket pins from loosening, prepare the pins as
follows:
Tools required: Screwdriver Torx #T20 ( )
1. Attach the key ring of the steel wire [6] to the Socket pins [5].
2. On the outrig pole for the winder base, fix the wire [6 ]to the
corresponding hole position using the enclosed self-tapping
torx screws [7].
3. On the cart, fix the wires [6] to the opposite hole positions
beside the outrig slots in each corner of the cart using the
enclosed self-tapping torx screws [7].
Attaching the winder base
1. Release the Socket pin [5] on the pole.
2. Insert the winder base [1] into the pole.
3. Reinsert the Socket pin [5] and ensure it is fully inserted and
locked.
2 Preparations and application
d&b E7494 Rigging manual 1.3 en4

Preparations and application
Extension length
Each outrig pole is provided with hole pairs positioned at specific
distances to allow for two different extension lengths of the poles.
This provides more flexibility on-site.
Footprints* (dimensions)
Full size (W x D) Front extension (W x D) Rear extension (W x D)
E7490 GSL Touring cart 1.7 x 2 m / 5.6 x 6.6 ft 1.7 x 1.7 m / 5.6 x 5.6 ft 1.7 x 1.7 m / 5.6 x 5.6 ft
E7495 KSL Touring cart - Tension 1.4 x 2 m / 4.6 x 6.6 ft 1.3 x 1.7 m / 4.3 x 5.6 ft 1.3 x 1.7 m / 4.3 x 5.6 ft
E7802 KSL Touring cart 1.4 x 1.85 m / 4.6 x 6 ft Not applicable Not applicable
*Graphics shown without loudspeaker cabinets for better illustration
d&b E7494 Rigging manual 1.3 en 5

Preparations and application
Attaching the poles to the cart
Note: Graphics shown without loudspeaker cabinets for
better illustration.
To release and reinsert the Socket pins, you have to access them
from underneath the cart.
1. On the cart, release all Socket pins of the corresponding slot.
2. Insert the pole to the desired extension length.
3. Reinsert all Socket pins and ensure they are fully inserted and
locked.
4. For the remaining poles, proceed in the same manner.
d&b E7494 Rigging manual 1.3 en6

Manufacturer's declaration
3.1 EU conformity (CE symbol)
This declaration applies to:
d&b E7494 SL Outrigger
manufactured by d&b audiotechnik GmbH & Co. KG.
All product variants are included, provided they correspond to the
original technical version and have not been subject to any later
design or electromechanical modifications.
We herewith declare that said products are in conformity with the
provisions of the respective EC directives including all applicable
amendments.
A detailed declaration is available on request and can be ordered
from d&b or downloaded from the d&b website at
www.dbaudio.com.
3.2 Disposal
When out of use the rigging components must be disposed of in
accordance with the national environmental regulations.
Ensure that damaged rigging components are disposed of in a
way that they cannot be used again.
3 Manufacturer's declaration
d&b E7494 Rigging manual 1.3 en 7

D2736.EN .01, 10/2020 © d&b audiotechnik GmbH & Co. KG
www.dbaudio.com