d & b audiotechnik E3 User manual

E3
Manual (3.1 EN)

Symbols on the equipment
Please refer to the information in the operating manual.
WARNING!
Dangerous voltage!
Contents
Safety precautions...............................................................3
Information regarding use of loudspeakers...............................................3
E3 ..........................................................................................4
Connections.........................................................................................................4
Operation with D6 or D12.............................................................................5
Operation with E-PAC......................................................................................5
Operation with P1200A..................................................................................6
Dispersion characteristics.................................................................................6
Altering the HF horn dispersion.....................................................................7
Technical specifications.....................................................................................7
Manufacturer's declarations................................................8
EU conformity of loudspeakers (CE symbol)..............................................8
WEEE Declaration (Disposal)..........................................................................8
General Information
E3 Manual
Version 3.1 EN, 03/2008, D2072.E.03
Copyright © 2008 by d&b audiotechnik GmbH; all rights reserved.
Keep this manual with the product or in a safe place so that it is
available for future reference.
When reselling this product, hand over this manual to the new
customer.
If you supply d&b products, please draw the attention of your customers
to this manual. Enclose the relevant manuals with the systems. If you
require additional manuals for this purpose, you can order them from
d&b.
d&b audiotechnik GmbH
Eugen-Adolff-Strasse 134, D-71522 Backnang, Germany
Telephone [phone], Fax [phone]
E-mail: [email protected], Internet: www.dbaudio.com

Safety precautions
Information regarding use of loudspeakers
WARNING! Never stand in the immediate vicinity of loudspeakers driven at a high
level. Professional loudspeaker systems are capable of causing a
sound pressure level detrimental to human health. Seemingly non-
critical sound levels (from approx. 95 dB SPL) can cause hearing
damage if people are exposed to it over a long period.
In order to prevent accidents when deploying loudspeakers on the
ground or when flown, please take note of the following:
When setting up the loudspeakers or loudspeaker stands, make sure
they are standing on a firm surface. If you place several systems on
top of one another, use straps to secure them against movement.
Only use accessories which have been tested and approved by d&b
for assembly and mobile deployment. Pay attention to the correct
application and maximum load capacity of the accessories as detailed
in our specific "Mounting instructions" or in our "Flying system and
rigging manuals".
Ensure that all additional hardware, fixings and fasteners used for
installation or mobile deployment are of an appropriate size and load
safety factor. Pay attention to the manufacturers' instructions and to
the relevant safety guidelines.
Regularly check the loudspeaker housings and accessories for visible
signs of wear and tear and replace them when necessary.
Regularly check all load bearing bolts in the mounting devices.
CAUTION! Loudspeakers produce a static magnetic field even if they are not
connected or are not in use. Therefore make sure when erecting and
transporting loudspeakers that they are nowhere near equipment and
objects which may be impaired or damaged by an external magnetic
field. Generally speaking, a distance of 0.5 m (1.5 ft) from magnetic
data carriers (floppy disks, audio and video tapes, bank cards, etc.) is
sufficient; a distance of more than 1 m (3 ft) may be necessary with
computer and video monitors.
E3 Manual (3.1 EN) Safety precautions - 1

E3
60
90
Fig. 1: E3 loudspeaker
The E3 loudspeaker is a full range, two way bass-reflex enclosure which
is fitted with a single 6.5" LF driver passively connected to a 1" HF
compression driver. This is coupled to a constant directivity horn with a
90° x 60° dispersion. Illustrated in the drawing on the left is an E3 with
the standard 90° horizontal horn configuration. The horn can be
rotated through 90° for a reversed 60° x 90° dispersion.
The E3 cabinet is constructed from marine plywood with an impact
resistant paint finish. The front of the loudspeaker cabinet is fitted with a
rigid metal grill covered with a replaceable acoustically transparent
foam. Two mounting locations are incorporated for the connector plate
to facilitate various deployment options. Eight M8 threaded inserts are
provided for mounting brackets and rigging.
NOTICE: Only operate E3 cabinets with a correctly configured d&b amplifier,
otherwise there is a risk of damaging the loudspeaker components.
Connections
Passive
Crossover
1+
1–
2+
2–
1+
1–
2+
2–
Fig. 2: Wiring of the NL4 connectors
The E3 cabinet is fitted with two NL4 connectors. All four pins of both
connectors are wired in parallel. The E3 uses the pin assignments
1+/1–. Pins 2+/2– are designated to active d&b subwoofers.
Using one connector as the input, the second connector allows for direct
connection to additional cabinets.
Swapping the connector and blank plates
The connector plate is fitted to the E3 rear panel. Next to it, on the left
hand side panel, is a metal blank plate with the cabinet details and
serial number. The connector and blank plates can be swapped over to
allow mounting brackets to be fitted to the back panel of the cabinet or
to allow it to be placed on its back as a stage monitor.
To swap the connector and blank plates, proceed as follows:
Tools required: 2.5 mm Allen key.
- Remove the connector plate by undoing the four 2.5 mm hex head
screws and disconnecting the connector wiring.
- Undo the four 2.5 mm hex head screws securing the blank plate and
remove the plate.
- Swap the panels. To refit the connector plate at the desired position,
reconnect the wiring (red: 1+, black: 1–).
- Refit the connector plate and refasten the screws.
NOTICE: Ensure the gasket of the plate is in the correct position.
- Refit the blind plate in the same manner.
E3 Manual (3.1 EN) Page 4 of 8

Operation with D6 or D12
Select the controller setup E3.
Within the D12 amplifier this is available in "Dual Channel" and "Mix
TOP/SUB" mode.
Up to a total of four E3 loudspeakers can be driven by each D6 or D12
amplifier channel.
Controller settings
For acoustic adjustment the functions CUT, HFA and CPL can be
selected.
CUT circuit
Set to CUT, a high pass filter with a 110 Hz cut off frequency is inserted
in the controller signal path. The E3 is now configured for use with d&b
active subwoofers.
-5
0
5
10
-10
-15
-20
-25
-30
20 100 1k 10k 20k
Fig. 3: Frequency response correction of
HFA circuit
HFA circuit
In HFA mode (High Frequency Attenuation), the HF response of the E3
system is rolled off. The HFA circuit provides a natural, balanced
frequency response when a unit is placed close to listeners in near field
or delay use.
High frequency attenuation begins gradually at 1 kHz, dropping by
approximately 3 dB at 10 kHz. This roll-off mimics the decline in
frequency response experienced when listening to a system from a
distance in a typically reverberant room or auditorium.
Fig. 4: Frequency response correction of
CPL circuit
CPL circuit
The CPL (Coupling) circuit compensates for coupling effects between the
cabinets when building closely coupled arrays. CPL begins gradually at
1 kHz, with maximum attenuation below 250 Hz, providing a balanced
frequency response when E3 cabinets are used in arrays of two or
more. The function of the CPL circuit is shown in the diagram opposite
and can be set in dB attenuation values between –9 and 0 dB.
REMOTE
LO IMP
DELAY ON
CUT
HFA
SPKR
213456 87
LO IMP
1
REMOTE
21 3 45 6
234
ONON
Version 1 Version 2
Fig. 5: E-PAC Configuration for E3
Operation with E-PAC
To drive the E3 cabinet the E-PAC has to be configured to E3 mode.
For an E-PAC version 1 or 2, the configuration is selected by setting the
appropriate DIP switches on the rear panel.
For an E-PAC version 3, the configuration is set via the encoder in
conjunction with an LCD.
Selecting E3 mode enables the E-PAC to drive up to two E3 cabinets.
LO IMP mode allows the E-PAC to drive four E3 cabinets with a 6 dB
reduction of input level to the loudspeakers.
The CUT and HFA settings are available. The characteristics of the CUT
and HFA settings are explained in the previous section "Operation with
D6 or D12 - Controller settings".
E3 Manual (3.1 EN) Page 5 of 8

Operation with P1200A
Fig. 6: Controls on E3
controller module
Up to four E3 cabinets can be driven by each P1200A power amplifier
channel fitted with an E3 controller module. Fitting one E3 and one
subwoofer controller module allows a single mainframe to drive four
E3s and two active subwoofer cabinets. All cabinets can be linked
together locally and fed by a single 4-wire cable from either mainframe
output connector
The CUT and HFA settings are available. The characteristics of the CUT
and HFA settings are explained in the previous section "Operation with
D6 or D12 - Controller settings".
Dispersion characteristics
The diagrams below show dispersion angle vs frequency plotted using
lines of equal sound pressure (isobars) at –6 dB and –12 dB.
Fig. 7: E3 isobar diagram configuration 90° horizontal (standard)
Fig. 8: E3 isobar diagram configuration 90° vertical
E3 Manual (3.1 EN) Page 6 of 8

60
90
60
90
Altering the HF horn dispersion
The E3 HF horn can be rotated through 90°. Two dispersion angles, 90°
and 60°, are engraved on the flange. The value on the horizontal edge
indicates the loudspeaker's horizontal dispersion angle.
Tools required: Phillips screwdriver, 3 mm Allen key.
- Remove the front grill by undoing the two Allen screws (M4x25 mm)
at the top and bottom of the grill.
- Undo the four Allen screws (M4x25 mm) which hold the horn in place
and rotate the horn through 90°.
NOTICE: Ensure the gasket of the horn is in the correct position.
- Refasten the horn and refit the front grill.
Technical specifications
Fig. 9: E3 frequency response standard
and CUT settings
E3 system data
Frequency response (–5 dB)....................................................................80 Hz - 18 kHz
Max. sound pressure (1 m, free field) with D12................................................123 dB
Max. sound pressure (1 m, free field) with D6..................................................122 dB
Max. sound pressure (1 m, free field) with P1200A........................................122 dB
(SPLmax peak, pink noise test signal with crest factor of 4)
Input level (100 dB SPL / 1 m)............................................................................–10 dBu
E3 loudspeaker
Nominal impedance...............................................................................................16 ohms
Power handling capacity (RMS / peak 10 ms).........................................120/480 W
Nominal dispersion angle...................................................................................90° x 60°
.............................................................................................(rotatable through 60° x 90°)
Components............................................................................................6.5" loudspeaker,
.................................................................................1" compression driver with CD horn
....................................................................................................Passive crossover network
Connections..............................................................................................................2 x NL4
Pin assignments...........................................................................................................1+/1–
Weight..........................................................................................................7.2 kg (15.9 lb)
Fig. 10: E3 cabinet dimensions in mm [inch] and angle ranges
E3 Manual (3.1 EN) Page 7 of 8

Manufacturer's declarations
EU conformity of loudspeakers (CE symbol)
This declaration applies to:
d&b E3 loudspeaker, Z0300
manufactured by d&b audiotechnik GmbH.
All production versions of this type are included, provided they
correspond to the original technical version and have not been subject
to any later design or electromechanical modifications.
We herewith declare that said products are in conformity with the
provisions of the respective EC directives including all applicable
amendments.
A detailed declaration is available on request and can be ordered from
d&b or downloaded from the d&b website at www.dbaudio.com.
WEEE Declaration (Disposal)
Electrical and electronic equipment must be disposed of separately from
normal waste at the end of its operational lifetime.
Please dispose of this product according to the respective national
regulations or contractual agreements. If there are any further questions
concerning the disposal of this product please contact d&b audiotechnik.
d&b audiotechnik GmbH, Eugen-Adolff-Str. 134, D-71522 Backnang, Germany, Phone [phone], Fax [phone]
D2072.E.03, 03/2008 © d&b audiotechnik GmbH