D-Link DI-624S - AirPlus Xtreme G Wireless 108G USB Storage... User manual

1. If you purchased this router to share your high-speed Internet connection with other
computers, you must have either an Ethernet-based Cable or a DSL modem with an
established Internet account from an Internet Service Provider (ISP).
2. It’s best to use the same computer that is connected to your modem for configuring
the DI-624S router. The DI-624S Wireless Storage Router acts as a DHCP server
and will assign all the necessary IP address information on your network. See
Appendix at the end of this Quick Installation Guide or the Manual on the CD-
ROM for setting each network adapter to automatically obtain an IP address.
Check Your Package Contents
These are the items included with your DI-624S purchase:
If any of the above items are missing, please contact your reseller.
©2005 D-Link Systems, Inc. All rights reserved. Trademarks or registered trademarks are the property of their respective
holders. Software and specifications subject to change without notice.
This product can be set up using any
current web browser, i.e., Internet
Explorer 6x, Netscape Navigator 7x.
DI-624S
AirPlus XtremeG ™
Wireless Storage Router
• DI-624S Wireless Storage Router with Antenna
• CD-ROM (containing Manual and Warranty)
• Ethernet (Cat.5 UTP/Straight-Through) Cable
• 5V DC, 3 A Power Adapter
Using a powe
r
supply with a
different voltage rating
will damage and void
the warranty for this
product.
Before You Begin

2
Connecting The DI-624S Wireless
Storage Router To Your Network
A. First, connect the power adapter to the receptor at the back panel of the DI-
624S and then plug the other end of the power adapter to a wall outlet or power
strip. The Power LED will turn ON to indicate proper operation.
B. Insert one end of an Ethernet cable to the WAN port on the back panel of the
DI-624S and the other end to the Ethernet port located on your Cable or DSL
modem. The WAN LED light will illuminate to indicate proper connection.
C. Insert one end of an Ethernet cable to LAN port 1 on the back panel of the DI-
624S and the other end to an available Ethernet port on the network adapter in the
computer you will use to configure the DI-624S. The LED light for LAN Port 1 will
illuminate to indicate proper connection. (Note: Some computers already have
network adapters pre-installed.)
Restart Your Computer
A
.Receptor for
Power Ada
p
te
r
B.WAN Port
This is the
connection for the
Ethernet Cable to
Ethernet Port on the
Cable or DSL
Modem.
C.LAN Ports
These are the
connections for
Ethernet cables to
your Ethernet-
enabled com
p
uters
Reset Button
Pressing this button
restores the router
to its original factory
default settings.
USB Ports
These are the
connections for you USB
devices, such as a
printer or network
stora
g
e device.
Antenna
Used for the
wireless
service of your
DI-624S.

3
Connecting Additional Devices to the
DI-624S Wireless Storage Router
Using additional Ethernet (Cat.5 UTP/Straight-Through) cables, connect
your Ethernet-equipped computer(s) to one of the 3 remaining Ethernet
LAN ports on the back panel of the DI-624S.
Additional devices may be added to your DI-624S to increase functionality.
By connecting a printer, network storage device or the D-Link Media
Lounge to either of the two USB ports at the back of the router, you may
share print capabilities, entertainment media or documents over your
wireless or wired network. A valid USB connection will cause the
corresponding USB LED at the front to light. For more information
regarding USB connections and device implementation, see the DI-624S
user guide.
LAN Port LEDs.
Each of the LAN ports on the back
of the DI-624S have a corresponding
LED light on the front panel of the
unit. When a proper connection has
been made to a computer that is ON,
the LED on the front panel should
illuminate.
USB Port LEDs.
Each of the USB ports on the back
of the DI-624S have a corresponding
LED light on the front panel of the
unit. When a proper connection has
been made to a device that is ON,
the LED on the front panel should
illuminate.

4
When you have completed the steps in this Quick Installation Guide, your
connected network should look similar to this:
Cable o
r
DSL
Modem
connected to
the WAN port.
DI-624S Wireless
Storage Router
Computers
connected
to the LAN
Ports
Computers
connected
on the
wireless
network
Devices
connected
to the USB
ports.

5
Using The Setup Wizard
The logon pop-up screen will appear.
Once you have logged in, the Home screen will appear.
Open your Web
browser and type
“http://192.168.0.1” into
the URL address box.
Then press the Enter or
Return key.
Click OK
Click Run Wizard
Type “admin” for
the username and
leave the password
field blank.

6
You will see the following screens.
Step 1 - Set up your new password.You have the option to establish a password.
Step 2 - Choose your time zone.
Click Next
Click Next
Click Next

7
The Setup Wizard (continued)
Select the type of Internet connection for your router.
If you selected Dynamic IP Address, this screen will appear:
Select one of
these settings
Click Next
If you are unsure of which setting to
select, please contact your Internet
Service Provider.
What is a MAC address? Each
network adapter has a discrete
Media Access Control (MAC)
address. Note that some computers
and peripherals may already include
built-in network adapters.
Click Next
“Clone MAC Address”
button to automatically
copy the MAC address
of the network adapter in
your computer. You can
also manually type in the
MAC address.

8
If your ISP requires a Static IP Address, and this option is selected, then this screen
will appear:
If your ISP uses PPPoE (Point-to-Point Protocol over Ethernet) and this option is
selected, then this screen will appear:
Click Next
Enter in the username
and password provided
to you by your ISP and
retype that same
password to verify it.
Click Next
Please be sure to remove an
y
existing PPPoE client software
installed on your computers.
Enter the IP address
information originally
provided to you by your
ISP. You will need to
complete all the required
fields.

9
If your ISP uses PPTP and this option is selected, then this screen will appear.
If your ISP uses L2PT and this option is selected, then this screen will appear.
Enter the IP address
information originally
provided to you by your
ISP.
Click Next
Enter the IP address
information originally
provided to you by your
ISP.
Click Next

10
If your ISP is Big Pond Cable and this option is selected, then this screen will appear.
After clicking Next in one of the previous screens, the wizard will open to the Wireless
installation for your router. Follow the explanation to quickly set up the wireless
function for your router.
Enter the WLAN name for
your network
Choose the wireless channel
to be used for your WLAN
from the pull down menu.
Click Next
Enter in the username
and password provided
to you by your ISP and
retype that same
password to verify it.
Click Next
Choose the wireless security
setup. Both security choices
need authentication input.