Daikin RYYQ8U7Y1B User guide

Installer and user reference guide
VRV IV+ heat pump
RYYQ8U7Y1B*
RYYQ10U7Y1B*
RYYQ12U7Y1B*
RYYQ14U7Y1B*
RYYQ16U7Y1B*
RYYQ18U7Y1B*
RYYQ20U7Y1B*
RYMQ8U5/U7Y1B*
RYMQ10U5/U7Y1B*
RYMQ12U5/U7Y1B*
RYMQ14U5/U7Y1B*
RYMQ16U5/U7Y1B*
RYMQ18U5/U7Y1B*
RYMQ20U5/U7Y1B*
RXYQ8U5/U7Y1B*
RXYQ10U5/U7Y1B*
RXYQ12U5/U7Y1B*
RXYQ14U5/U7Y1B*
RXYQ16U5/U7Y1B*
RXYQ18U5/U7Y1B*
RXYQ20U5/U7Y1B*

Table of contents
Installer and user reference guide
2
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
Table of contents
1 About the documentation 6
1.1 About this document ...................................................................................................................................................... 6
1.2 Meaning of warnings and symbols................................................................................................................................. 6
2 General safety precautions 8
2.1 For the installer............................................................................................................................................................... 8
2.1.1 General ........................................................................................................................................................... 8
2.1.2 Installation site ............................................................................................................................................... 9
2.1.3 Refrigerant — in case of R410A or R32.......................................................................................................... 9
2.1.4 Electrical ......................................................................................................................................................... 11
3 Specific installer safety instructions 14
For the user 17
4 User safety instructions 18
4.1 General............................................................................................................................................................................ 18
4.2 Instructions for safe operation ....................................................................................................................................... 19
5 About the system 22
5.1 System layout.................................................................................................................................................................. 22
6 User interface 24
7 Operation 25
7.1 Before operation............................................................................................................................................................. 25
7.2 Operation range.............................................................................................................................................................. 26
7.3 Operating the system ..................................................................................................................................................... 26
7.3.1 About operating the system........................................................................................................................... 26
7.3.2 About cooling, heating, fan only, and automatic operation ......................................................................... 27
7.3.3 About the heating operation.......................................................................................................................... 27
7.3.4 To operate the system (WITHOUT cool/heat changeover remote control switch)...................................... 28
7.3.5 To operate the system (WITH cool/heat changeover remote control switch)............................................. 28
7.4 Using the dry program.................................................................................................................................................... 29
7.4.1 About the dry program................................................................................................................................... 29
7.4.2 To use the dry program (WITHOUT cool/heat changeover remote control switch) .................................... 29
7.4.3 To use the dry program (WITH cool/heat changeover remote control switch) ........................................... 29
7.5 Adjusting the air flow direction ...................................................................................................................................... 30
7.5.1 About the air flow flap.................................................................................................................................... 30
7.6 Setting the master user interface................................................................................................................................... 31
7.6.1 About setting the master user interface........................................................................................................ 31
7.6.2 To designate the master user interface (VRV DX and Hydrobox) ................................................................. 32
7.7 About control systems .................................................................................................................................................... 32
8 Energy saving and optimum operation 33
8.1 Available main operation methods ................................................................................................................................ 33
8.2 Available comfort settings .............................................................................................................................................. 34
9 Maintenance and service 35
9.1 Maintenance after a long stop period............................................................................................................................ 35
9.2 Maintenance before a long stop period......................................................................................................................... 36
9.3 About the refrigerant...................................................................................................................................................... 36
9.4 After-sales service and warranty .................................................................................................................................... 36
9.4.1 Warranty period ............................................................................................................................................. 36
9.4.2 Recommended maintenance and inspection................................................................................................ 37
9.4.3 Recommended maintenance and inspection cycles ..................................................................................... 37
9.4.4 Shortened maintenance and replacement cycles ......................................................................................... 38
10 Troubleshooting 39
10.1 Error codes: Overview .................................................................................................................................................... 40
10.2 Symptoms that are NOT system malfunctions............................................................................................................... 43
10.2.1 Symptom: The system does not operate....................................................................................................... 43
10.2.2 Symptom: Cool/Heat cannot be changed over ............................................................................................. 43
10.2.3 Symptom: Fan operation is possible, but cooling and heating do not work ................................................ 43
10.2.4 Symptom: The fan speed does not correspond to the setting...................................................................... 43
10.2.5 Symptom: The fan direction does not correspond to the setting................................................................. 43

Table of contents
Installer and user reference guide
3
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
10.2.6 Symptom: White mist comes out of a unit (Indoor unit) .............................................................................. 44
10.2.7 Symptom: White mist comes out of a unit (Indoor unit, outdoor unit)........................................................ 44
10.2.8 Symptom: The user interface reads "U4" or "U5" and stops, but then restarts after a few minutes.......... 44
10.2.9 Symptom: Noise of air conditioners (Indoor unit)......................................................................................... 44
10.2.10 Symptom: Noise of air conditioners (Indoor unit, outdoor unit) .................................................................. 44
10.2.11 Symptom: Noise of air conditioners (Outdoor unit)...................................................................................... 44
10.2.12 Symptom: Dust comes out of the unit........................................................................................................... 45
10.2.13 Symptom: The units can give off odours ....................................................................................................... 45
10.2.14 Symptom: The outdoor unit fan does not spin.............................................................................................. 45
10.2.15 Symptom: The display shows "88"................................................................................................................. 45
10.2.16 Symptom: The compressor in the outdoor unit does not stop after a short heating operation ................. 45
10.2.17 Symptom: The inside of an outdoor unit is warm even when the unit has stopped.................................... 45
10.2.18 Symptom: Hot air can be felt when the indoor unit is stopped.................................................................... 45
11 Relocation 46
12 Disposal 47
13 Technical data 48
13.1 Eco Design requirements................................................................................................................................................ 48
For the installer 49
14 About the box 50
14.1 About LOOP BY DAIKIN ................................................................................................................................................... 50
14.2 Overview: About the box ................................................................................................................................................ 50
14.3 To unpack the outdoor unit............................................................................................................................................ 51
14.4 To remove the accessories from the outdoor unit ........................................................................................................ 52
14.5 Accessory pipes: Diameters ............................................................................................................................................ 52
14.6 To remove the transportation stay ................................................................................................................................ 53
15 About the units and options 54
15.1 Overview: About the units and options.......................................................................................................................... 54
15.2 Identification label: Outdoor unit................................................................................................................................... 54
15.3 About the outdoor unit................................................................................................................................................... 55
15.4 System layout.................................................................................................................................................................. 55
15.5 Combining units and options.......................................................................................................................................... 56
15.5.1 About combining units and options............................................................................................................... 56
15.5.2 Possible combinations of indoor units........................................................................................................... 56
15.5.3 Possible combinations of outdoor units ........................................................................................................ 57
15.5.4 Possible options for the outdoor unit............................................................................................................ 58
16 Unit installation 60
16.1 Preparing the installation site......................................................................................................................................... 60
16.1.1 Installation site requirements of the outdoor unit........................................................................................ 60
16.1.2 Additional installation site requirements of the outdoor unit in cold climates............................................ 62
16.1.3 Securing safety against refrigerant leaks ....................................................................................................... 63
16.2 Opening the unit ............................................................................................................................................................. 65
16.2.1 About opening the units................................................................................................................................. 65
16.2.2 To open the outdoor unit............................................................................................................................... 65
16.2.3 To open the electrical component box of the outdoor unit ......................................................................... 66
16.3 Mounting the outdoor unit............................................................................................................................................. 67
16.3.1 To provide the installation structure ............................................................................................................. 67
17 Piping installation 69
17.1 Preparing refrigerant piping ........................................................................................................................................... 69
17.1.1 Refrigerant piping requirements.................................................................................................................... 69
17.1.2 Refrigerant piping insulation.......................................................................................................................... 70
17.1.3 To select the piping size ................................................................................................................................. 70
17.1.4 To select refrigerant branch kits .................................................................................................................... 73
17.1.5 About the piping length.................................................................................................................................. 75
17.1.6 Piping length: VRV DX only............................................................................................................................. 75
17.1.7 Piping length: VRV DX and Hydrobox............................................................................................................. 79
17.1.8 Piping length: VRV DX and RA DX................................................................................................................... 80
17.1.9 Multiple outdoor units: Possible layouts ....................................................................................................... 81
17.2 Connecting the refrigerant piping .................................................................................................................................. 82
17.2.1 About connecting the refrigerant piping ....................................................................................................... 82
17.2.2 Precautions when connecting the refrigerant piping.................................................................................... 83
17.2.3 Multiple outdoor units: Knockout holes ........................................................................................................ 84
17.2.4 To route the refrigerant piping ...................................................................................................................... 84

Table of contents
Installer and user reference guide
4
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
17.2.5 To connect the refrigerant piping to the outdoor unit ................................................................................. 85
17.2.6 To connect the multi connection piping kit................................................................................................... 85
17.2.7 To connect the refrigerant branching kit....................................................................................................... 86
17.2.8 To protect against contamination.................................................................................................................. 86
17.2.9 To braze the pipe end..................................................................................................................................... 87
17.2.10 Using the stop valve and service port............................................................................................................ 88
17.2.11 To remove the spun pipes.............................................................................................................................. 90
17.3 Checking the refrigerant piping ...................................................................................................................................... 91
17.3.1 About checking the refrigerant piping........................................................................................................... 91
17.3.2 Checking refrigerant piping: General guidelines ........................................................................................... 92
17.3.3 Checking refrigerant piping: Setup ................................................................................................................ 93
17.3.4 To perform a leak test .................................................................................................................................... 93
17.3.5 To perform vacuum drying............................................................................................................................. 94
17.3.6 To insulate the refrigerant piping .................................................................................................................. 95
17.4 Charging refrigerant........................................................................................................................................................ 95
17.4.1 Precautions when charging refrigerant ......................................................................................................... 95
17.4.2 About charging refrigerant............................................................................................................................. 96
17.4.3 To determine the additional refrigerant amount.......................................................................................... 97
17.4.4 To charge refrigerant: Flow chart .................................................................................................................. 100
17.4.5 To charge refrigerant...................................................................................................................................... 102
17.4.6 Step 6a: To automatically charge refrigerant ................................................................................................ 104
17.4.7 Step 6b: To manually charge refrigerant ....................................................................................................... 106
17.4.8 Error codes when charging refrigerant.......................................................................................................... 107
17.4.9 Checks after charging refrigerant .................................................................................................................. 107
17.4.10 To fix the fluorinated greenhouse gases label............................................................................................... 108
18 Electrical installation 109
18.1 About connecting the electrical wiring .......................................................................................................................... 109
18.1.1 Precautions when connecting the electrical wiring....................................................................................... 109
18.1.2 Field wiring: Overview .................................................................................................................................... 111
18.1.3 About the electrical wiring ............................................................................................................................. 111
18.1.4 Guidelines when knocking out knockout holes ............................................................................................. 112
18.1.5 About electrical compliance........................................................................................................................... 113
18.1.6 Safety device requirements ........................................................................................................................... 114
18.2 To route and fix the transmission wiring........................................................................................................................ 116
18.3 To connect the transmission wiring ............................................................................................................................... 117
18.4 To finish the transmission wiring.................................................................................................................................... 118
18.5 To route and fix the power supply ................................................................................................................................. 118
18.6 To connect the power supply ......................................................................................................................................... 119
18.7 To check the insulation resistance of the compressor .................................................................................................. 120
19 Configuration 121
19.1 Overview: Configuration................................................................................................................................................. 121
19.2 Making field settings....................................................................................................................................................... 121
19.2.1 About making field settings............................................................................................................................ 121
19.2.2 Field setting components............................................................................................................................... 123
19.2.3 To access the field setting components......................................................................................................... 123
19.2.4 To access mode 1 or 2.................................................................................................................................... 124
19.2.5 To use mode 1 ................................................................................................................................................ 125
19.2.6 To use mode 2 ................................................................................................................................................ 125
19.2.7 Mode 1: Monitoring settings ......................................................................................................................... 126
19.2.8 Mode 2: Field settings .................................................................................................................................... 129
19.2.9 To connect the PC configurator to the outdoor unit..................................................................................... 136
19.3 Energy saving and optimum operation .......................................................................................................................... 136
19.3.1 Available main operation methods................................................................................................................ 137
19.3.2 Available comfort settings.............................................................................................................................. 138
19.3.3 Example: Automatic mode during cooling..................................................................................................... 140
19.3.4 Example: Automatic mode during heating .................................................................................................... 141
19.4 Using the leak detection function .................................................................................................................................. 142
19.4.1 About automatic leak detection .................................................................................................................... 142
19.4.2 To manually perform a leak detection........................................................................................................... 143
20 Commissioning 145
20.1 Overview: Commissioning .............................................................................................................................................. 145
20.2 Precautions when commissioning .................................................................................................................................. 145
20.3 Checklist before commissioning ..................................................................................................................................... 146
20.4 About the test run........................................................................................................................................................... 147
20.5 To perform a test run...................................................................................................................................................... 148
20.6 Correcting after abnormal completion of the test run .................................................................................................. 149
20.7 Operating the unit........................................................................................................................................................... 150

Table of contents
Installer and user reference guide
5
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
21 Hand-over to the user 151
22 Maintenance and service 152
22.1 Maintenance safety precautions .................................................................................................................................... 152
22.1.1 To prevent electrical hazards ......................................................................................................................... 152
22.2 About service mode operation ....................................................................................................................................... 153
22.2.1 To use vacuum mode ..................................................................................................................................... 153
22.2.2 To recover refrigerant .................................................................................................................................... 153
23 Troubleshooting 155
23.1 Solving problems based on error codes ......................................................................................................................... 155
23.2 Error codes: Overview .................................................................................................................................................... 155
24 Disposal 161
25 Technical data 162
25.1 Service space: Outdoor unit ........................................................................................................................................... 162
25.2 Piping diagram: Outdoor unit ......................................................................................................................................... 164
25.3 Wiring diagram: Outdoor unit ........................................................................................................................................ 167
26 Glossary 173

1 | About the documentation
Installer and user reference guide
6
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
1 About the documentation
In this chapter
1.1 About this document.............................................................................................................................................................. 6
1.2 Meaning of warnings and symbols......................................................................................................................................... 6
1.1 About this document
Target audience
Authorised installers + end users
INFORMATION
This appliance is intended to be used by expert or trained users in shops, in light
industry and on farms, or for commercial use by lay persons.
Documentation set
This document is part of a documentation set. The complete set consists of:
▪General safety precautions:
-Safety instructions that you must read before installing
-Format: Paper (in the box of the outdoor unit)
▪Outdoor unit installation and operation manual:
-Installation and operation instructions
-Format: Paper (in the box of the outdoor unit)
▪Installer and user reference guide:
-Preparation of the installation, reference data,…
-Detailed step-by-step instructions and background information for basic and
advanced usage
-Format: Digital files on http://www.daikineurope.com/support-and-manuals/
product-information/
Latest revisions of the supplied documentation may be available on the regional
Daikin website or via your dealer.
The original documentation is written in English. All other languages are
translations.
Technical engineering data
▪A subset of the latest technical data is available on the regional Daikin website
(publicly accessible).
▪The full set of latest technical data is available on the Daikin Business Portal
(authentication required).
1.2 Meaning of warnings and symbols
DANGER
Indicates a situation that results in death or serious injury.

1 | About the documentation
Installer and user reference guide
7
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
DANGER: RISK OF ELECTROCUTION
Indicates a situation that could result in electrocution.
DANGER: RISK OF BURNING/SCALDING
Indicates a situation that could result in burning/scalding because of extreme hot or
cold temperatures.
DANGER: RISK OF EXPLOSION
Indicates a situation that could result in explosion.
WARNING
Indicates a situation that could result in death or serious injury.
WARNING: FLAMMABLE MATERIAL
CAUTION
Indicates a situation that could result in minor or moderate injury.
NOTICE
Indicates a situation that could result in equipment or property damage.
INFORMATION
Indicates useful tips or additional information.
Symbols used on the unit:
Symbol Explanation
Before installation, read the installation and operation
manual, and the wiring instruction sheet.
Before performing maintenance and service tasks, read the
service manual.
For more information, see the installer and user reference
guide.
The unit contains rotating parts. Be careful when servicing or
inspecting the unit.
Symbols used in the documentation:
Symbol Explanation
Indicates a figure title or a reference to it.
Example: " 1–3 Figure title" means "Figure 3 in chapter 1".
Indicates a table title or a reference to it.
Example: " 1–3 Table title" means "Table 3 in chapter 1".

2 | General safety precautions
Installer and user reference guide
8
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
2 General safety precautions
In this chapter
2.1 For the installer....................................................................................................................................................................... 8
2.1.1 General ................................................................................................................................................................... 8
2.1.2 Installation site ....................................................................................................................................................... 9
2.1.3 Refrigerant — in case of R410A or R32 ................................................................................................................. 9
2.1.4 Electrical ................................................................................................................................................................. 11
2.1 For the installer
2.1.1 General
If you are NOT sure how to install or operate the unit, contact your dealer.
DANGER: RISK OF BURNING/SCALDING
▪Do NOT touch the refrigerant piping, water piping or internal parts during and
immediately after operation. It could be too hot or too cold. Give it time to return
to normal temperature. If you MUST touch it, wear protective gloves.
▪Do NOT touch any accidental leaking refrigerant.
WARNING
Improper installation or attachment of equipment or accessories could result in
electrical shock, short-circuit, leaks, fire or other damage to the equipment. ONLY
use accessories, optional equipment and spare parts made or approved by Daikin.
WARNING
Make sure installation, testing and applied materials comply with applicable
legislation (on top of the instructions described in the Daikin documentation).
CAUTION
Wear adequate personal protective equipment (protective gloves, safety glasses,…)
when installing, maintaining or servicing the system.
WARNING
Tear apart and throw away plastic packaging bags so that nobody, especially
children, can play with them. Possible risk: suffocation.
WARNING
Provide adequate measures to prevent that the unit can be used as a shelter by small
animals. Small animals that make contact with electrical parts can cause
malfunctions, smoke or fire.
CAUTION
Do NOT touch the air inlet or aluminium fins of the unit.

2 | General safety precautions
Installer and user reference guide
9
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
CAUTION
▪Do NOT place any objects or equipment on top of the unit.
▪Do NOT sit, climb or stand on the unit.
In accordance with the applicable legislation, it might be necessary to provide a
logbook with the product containing at least: information on maintenance, repair
work, results of tests, stand-by periods,…
Also, at least, following information MUST be provided at an accessible place at the
product:
▪Instructions for shutting down the system in case of an emergency
▪Name and address of fire department, police and hospital
▪Name, address and day and night telephone numbers for obtaining service
In Europe, EN378 provides the necessary guidance for this logbook.
2.1.2 Installation site
▪Provide sufficient space around the unit for servicing and air circulation.
▪Make sure the installation site withstands the weight and vibration of the unit.
▪Make sure the area is well ventilated. Do NOT block any ventilation openings.
▪Make sure the unit is level.
Do NOT install the unit in the following places:
▪In potentially explosive atmospheres.
▪In places where there is machinery that emits electromagnetic waves.
Electromagnetic waves may disturb the control system, and cause malfunction of
the equipment.
▪In places where there is a risk of fire due to the leakage of flammable gases
(example: thinner or gasoline), carbon fibre, ignitable dust.
▪In places where corrosive gas (example: sulphurous acid gas) is produced.
Corrosion of copper pipes or soldered parts may cause the refrigerant to leak.
2.1.3 Refrigerant — in case of R410A or R32
If applicable. See the installation manual or installer reference guide of your
application for more information.
NOTICE
Make sure refrigerant piping installation complies with applicable legislation. In
Europe, EN378 is the applicable standard.
NOTICE
Make sure the field piping and connections are NOT subjected to stress.
WARNING
During tests, NEVER pressurise the product with a pressure higher than the
maximum allowable pressure (as indicated on the nameplate of the unit).

2 | General safety precautions
Installer and user reference guide
10
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
WARNING
Take sufficient precautions in case of refrigerant leakage. If refrigerant gas leaks,
ventilate the area immediately. Possible risks:
▪Excessive refrigerant concentrations in a closed room can lead to oxygen
deficiency.
▪Toxic gas might be produced if refrigerant gas comes into contact with fire.
DANGER: RISK OF EXPLOSION
Pump down – Refrigerant leakage. If you want to pump down the system, and there
is a leak in the refrigerant circuit:
▪Do NOT use the unit's automatic pump down function, with which you can collect
all refrigerant from the system into the outdoor unit. Possible consequence: Self-
combustion and explosion of the compressor because of air going into the
operating compressor.
▪Use a separate recovery system so that the unit's compressor does NOT have to
operate.
WARNING
ALWAYS recover the refrigerant. Do NOT release them directly into the environment.
Use a vacuum pump to evacuate the installation.
NOTICE
After all the piping has been connected, make sure there is no gas leak. Use nitrogen
to perform a gas leak detection.
NOTICE
▪To avoid compressor breakdown, do NOT charge more than the specified amount
of refrigerant.
▪When the refrigerant system is to be opened, refrigerant MUST be treated
according to the applicable legislation.
WARNING
Make sure there is no oxygen in the system. Refrigerant may ONLY be charged after
performing the leak test and the vacuum drying.
Possible consequence: Self-combustion and explosion of the compressor because of
oxygen going into the operating compressor.
▪In case recharge is required, see the nameplate of the unit. It states the type of
refrigerant and necessary amount.
▪The unit is factory charged with refrigerant and depending on pipe sizes and pipe
lengths some systems require additional charging of refrigerant.
▪ONLY use tools exclusively for the refrigerant type used in the system, this to
ensure pressure resistance and prevent foreign materials from entering into the
system.
▪Charge the liquid refrigerant as follows:

2 | General safety precautions
Installer and user reference guide
11
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
If Then
A siphon tube is present
(i.e., the cylinder is marked with "Liquid
filling siphon attached")
Charge with the cylinder upright.
A siphon tube is NOT present Charge with the cylinder upside down.
▪Open refrigerant cylinders slowly.
▪Charge the refrigerant in liquid form. Adding it in gas form may prevent normal
operation.
CAUTION
When the refrigerant charging procedure is done or when pausing, close the valve of
the refrigerant tank immediately. If the valve is NOT closed immediately, remaining
pressure might charge additional refrigerant. Possible consequence: Incorrect
refrigerant amount.
2.1.4 Electrical
DANGER: RISK OF ELECTROCUTION
▪Turn OFF all power supply before removing the switch box cover, connecting
electrical wiring or touching electrical parts.
▪Disconnect the power supply for more than 10minutes, and measure the voltage
at the terminals of main circuit capacitors or electrical components before
servicing. The voltage MUST be less than 50VDC before you can touch electrical
components. For the location of the terminals, see the wiring diagram.
▪Do NOT touch electrical components with wet hands.
▪Do NOT leave the unit unattended when the service cover is removed.
WARNING
If NOT factory installed, a main switch or other means for disconnection, having a
contact separation in all poles providing full disconnection under overvoltage
categoryIII condition, MUST be installed in the fixed wiring.

2 | General safety precautions
Installer and user reference guide
12
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
WARNING
▪ONLY use copper wires.
▪Make sure the field wiring complies with the applicable legislation.
▪All field wiring MUST be performed in accordance with the wiring diagram
supplied with the product.
▪NEVER squeeze bundled cables and make sure they do NOT come in contact with
the piping and sharp edges. Make sure no external pressure is applied to the
terminal connections.
▪Make sure to install earth wiring. Do NOT earth the unit to a utility pipe, surge
absorber, or telephone earth. Incomplete earth may cause electrical shock.
▪Make sure to use a dedicated power circuit. NEVER use a power supply shared by
another appliance.
▪Make sure to install the required fuses or circuit breakers.
▪Make sure to install an earth leakage protector. Failure to do so may cause
electrical shock or fire.
▪When installing the earth leakage protector, make sure it is compatible with the
inverter (resistant to high frequency electric noise) to avoid unnecessary opening
of the earth leakage protector.
CAUTION
▪When connecting the power supply: connect the earth cable first, before making
the current-carrying connections.
▪When disconnecting the power supply: disconnect the current-carrying cables
first, before separating the earth connection.
▪The length of the conductors between the power supply stress relief and the
terminal block itself MUST be as such that the current-carrying wires are
tautened before the earth wire is in case the power supply is pulled loose from
the stress relief.
NOTICE
Precautions when laying power wiring:
▪Do NOT connect wiring of different thicknesses to the power terminal block (slack
in the power wiring may cause abnormal heat).
▪When connecting wiring which is the same thickness, do as shown in the figure
above.
▪For wiring, use the designated power wire and connect firmly, then secure to
prevent outside pressure being exerted on the terminal board.
▪Use an appropriate screwdriver for tightening the terminal screws. A screwdriver
with a small head will damage the head and make proper tightening impossible.
▪Over-tightening the terminal screws may break them.
Install power cables at least 1 meter away from televisions or radios to prevent
interference. Depending on the radio waves, a distance of 1 meter may NOT be
sufficient.

2 | General safety precautions
Installer and user reference guide
13
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
WARNING
▪After finishing the electrical work, confirm that each electrical component and
terminal inside the electrical components box is connected securely.
▪Make sure all covers are closed before starting up the unit.
NOTICE
ONLY applicable if the power supply is three‑phase, and the compressor has an ON/
OFF starting method.
If there exists the possibility of reversed phase after a momentary black out and the
power goes ON and OFF while the product is operating, attach a reversed phase
protection circuit locally. Running the product in reversed phase can break the
compressor and other parts.

3 | Specific installer safety instructions
Installer and user reference guide
14
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
3 Specific installer safety instructions
Always observe the following safety instructions and regulations.
WARNING
Tear apart and throw away plastic packaging bags so that nobody, especially
children, can play with them. Possible risk: suffocation.
CAUTION
Appliance NOT accessible to the general public, install it in a secured area, protected
from easy access.
This unit, both indoor and outdoor, is suitable for installation in a commercial and
light industrial environment.
CAUTION
Excessive refrigerant concentrations in a closed room can lead to oxygen deficiency.
DANGER: RISK OF ELECTROCUTION
Do NOT leave the unit unattended when the service cover is removed.
DANGER: RISK OF BURNING/SCALDING
DANGER: RISK OF ELECTROCUTION
WARNING
Take sufficient precautions in case of refrigerant leakage. If refrigerant gas leaks,
ventilate the area immediately. Possible risks:
▪Excessive refrigerant concentrations in a closed room can lead to oxygen
deficiency.
▪Toxic gas might be produced if refrigerant gas comes into contact with fire.
WARNING
ALWAYS recover the refrigerant. Do NOT release them directly into the environment.
Use a vacuum pump to evacuate the installation.
WARNING
During tests, NEVER pressurise the product with a pressure higher than the
maximum allowable pressure (as indicated on the nameplate of the unit).
CAUTION
Do NOT vent gases into the atmosphere.
WARNING
Any gas or oil remaining inside the stop valve may blow off the spun piping.
If these instructions are NOT followed correctly it may result in property damage or
personal injury, which may be serious depending on the circumstances.

3 | Specific installer safety instructions
Installer and user reference guide
15
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
WARNING
NEVER remove the spun piping by brazing.
Any gas or oil remaining inside the stop valve may blow off the spun piping.
WARNING
▪ONLY use R410A as refrigerant. Other substances may cause explosions and
accidents.
▪R410A contains fluorinated greenhouse gases. Its global warming potential (GWP)
value is 2087.5. Do NOT vent these gases into the atmosphere.
▪When charging refrigerant, ALWAYS use protective gloves and safety glasses.
CAUTION
Do NOT push or place redundant cable length in the unit.
WARNING
▪If the power supply has a missing or wrong N-phase, equipment might break
down.
▪Establish proper earthing. Do NOT earth the unit to a utility pipe, surge absorber,
or telephone earth. Incomplete earthing may cause electrical shock.
▪Install the required fuses or circuit breakers.
▪Secure the electrical wiring with cable ties so that the cables do NOT come in
contact with sharp edges or piping, particularly on the high-pressure side.
▪Do NOT use taped wires, stranded conductor wires, extension cords, or
connections from a star system. They can cause overheating, electrical shock or
fire.
▪Do NOT install a phase advancing capacitor, because this unit is equipped with an
inverter. A phase advancing capacitor will reduce performance and may cause
accidents.
WARNING
▪All wiring MUST be performed by an authorised electrician and MUST comply
with the applicable legislation.
▪Make electrical connections to the fixed wiring.
▪All components procured on-site and all electrical construction MUST comply
with the applicable legislation.
WARNING
ALWAYS use multicore cable for power supply cables.

3 | Specific installer safety instructions
Installer and user reference guide
16
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
CAUTION
▪When connecting the power supply: connect the earth cable first, before making
the current-carrying connections.
▪When disconnecting the power supply: disconnect the current-carrying cables
first, before separating the earth connection.
▪The length of the conductors between the power supply stress relief and the
terminal block itself MUST be as such that the current-carrying wires are
tautened before the earth wire is in case the power supply is pulled loose from
the stress relief.
CAUTION
Do NOT perform the test operation while working on the indoor units.
When performing the test operation, NOT ONLY the outdoor unit, but the connected
indoor unit will operate as well. Working on an indoor unit while performing a test
operation is dangerous.
CAUTION
Do NOT insert fingers, rods or other objects into the air inlet or outlet. Do NOT
remove the fan guard. When the fan is rotating at high speed, it will cause injury.

For the user
Installer and user reference guide
17
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
For the user

4 | User safety instructions
Installer and user reference guide
18
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
4 User safety instructions
Always observe the following safety instructions and regulations.
In this chapter
4.1 General.................................................................................................................................................................................... 18
4.2 Instructions for safe operation............................................................................................................................................... 19
4.1 General
WARNING
If you are NOT sure how to operate the unit, contact your
installer.
WARNING
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the
hazards involved.
Children SHALL NOT play with the appliance.
Cleaning and user maintenance SHALL NOT be made by
children without supervision.
WARNING
To prevent electrical shocks or fire:
▪Do NOT rinse the unit.
▪Do NOT operate the unit with wet hands.
▪Do NOT place any objects containing water on the unit.
CAUTION
▪Do NOT place any objects or equipment on top of the
unit.
▪Do NOT sit, climb or stand on the unit.

4 | User safety instructions
Installer and user reference guide
19
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
▪Units are marked with the following symbol:
This means that electrical and electronic products may NOT be mixed with
unsorted household waste. Do NOT try to dismantle the system yourself: the
dismantling of the system, treatment of the refrigerant, of oil and of other parts
MUST be done by an authorised installer and MUST comply with applicable
legislation.
Units MUST be treated at a specialised treatment facility for reuse, recycling and
recovery. By ensuring this product is disposed of correctly, you will help to
prevent potential negative consequences for the environment and human
health. For more information, contact your installer or local authority.
▪Batteries are marked with the following symbol:
This means that the batteries may NOT be mixed with unsorted household
waste. If a chemical symbol is printed beneath the symbol, this chemical symbol
means that the battery contains a heavy metal above a certain concentration.
Possible chemical symbols are: Pb: lead (>0.004%).
Waste batteries MUST be treated at a specialised treatment facility for reuse. By
ensuring waste batteries are disposed of correctly, you will help to prevent
potential negative consequences for the environment and human health.
4.2 Instructions for safe operation
CAUTION
▪NEVER touch the internal parts of the controller.
▪Do NOT remove the front panel. Some parts inside are
dangerous to touch and appliance problems may
happen. For checking and adjusting the internal parts,
contact your dealer.
CAUTION
Do NOT operate the system when using a room
fumigation-type insecticide. Chemicals could collect in the
unit, and endanger the health of people who are
hypersensitive to chemicals.
CAUTION
It is unhealthy to expose your body to the air flow for a
long time.

4 | User safety instructions
Installer and user reference guide
20
RYYQ+RYMQ+RXYQ
VRV IV+ heat pump
4P546228-1C – 2021.11
CAUTION
To avoid oxygen deficiency, ventilate the room sufficiently
if equipment with burner is used together with the system.
WARNING
This unit contains electrical and hot parts.
WARNING
Before operating the unit, be sure the installation has been
carried out correctly by an installer.
WARNING
NEVER touch the air outlet or the horizontal blades while
the swing flap is in operation. Fingers may become caught
or the unit may break down.
CAUTION
Do NOT insert fingers, rods or other objects into the air
inlet or outlet. Do NOT remove the fan guard. When the
fan is rotating at high speed, it will cause injury.
CAUTION: Pay attention to the fan!
It is dangerous to inspect the unit while the fan is running.
Make sure to turn OFF the main switch before executing
any maintenance task.
CAUTION
After a long use, check the unit stand and fitting for
damage. If damaged, the unit may fall and result in injury.
WARNING
NEVER replace a fuse with a fuse of a wrong ampere
ratings or other wires when a fuse blows out. Use of wire
or copper wire may cause the unit to break down or cause
a fire.