DAISHIN SRM180K User manual

DAISHIN SRM180K Page 3
INTRODUCTION
Forword to the user
The DAISHIN team thanks you for your purshase.
Read this manual before any use of your mower, only the herein instructions shall help you to achieve an
efficient and safe work.
A safe use will only result from the manner you will use the machine in accordance with the restrictions
described in this manual. Thus, you must know and follow all the safety measures in this manual and those
relating to the use of your mower.
The MOWER that you have just bought has been designed and manufactured for your entire satisfaction. As any
other mechanical machine, it requires a proper maintenance and must be kept clean. Grease the machine like
indicated. Follow the rules and safety indications as described in this manual and as showed on the preventive
instruction stickers.
About maintenance, always mind that your DAISHIN dealer has the skills, the genuine parts and the necessary
tools to solve the possible problems.
Use only the DAISHIN original parts : “ non genuine ” parts will not assure you of a correct and safe
working and are likely to make the guarantee null and void. Write the name and the serial number of
your machine hereunder :
MODEL :.......................................................................................
SERIAL NUMBER (refer to the pictures herein) :.........................
Always mention these informations to your dealer in order to obtain the right parts.
Concerned about constant progress, DAISHIN keeps the right to modify the machines without being compelled
to modify those already sold.
The illustrations and specifications in this manual might lightely differ from your machine because of the constant
improvements made by our production department.
In this manual, the left and the right hand or the rear and the front position are determined according to the
mower handlebar.
All along this manual the word IMPORTANT is used to indicate that a fault might cause damage to the machine.
The words WARNING, CAUTION and DANGER are used with the “ safety/warning ” pictogram (triangle with an
exclamation mark) in order to indicate a hazard for your safety.
This symbol indicates that you must be very attentive because your safety is at stake. It reminds that you must
follow the safety instructions and pay attention to hazardous operations that might cause injuries.
WARNING
Reminds the safety rules that might cause injury if they are not respected
CAUTION
Remembers to pay attention to a real danger that is likely to cause injury or even death if no proper precaution is
taken.
Indicates a major hazard that is most likely to cause irremediable injury or death if the right precautions are not
taken.

DAISHIN SRM180K Page 4
SPECIFICATIONS
Model
SRM180K
Dimensions (L x l x h in mm)
2,030 x 705 x 1,100
Engine
KAWASAKI FJ180V - 4,5 kW
Transmission
Belt pulley & gears
Forward speed (km/h)
(1) 2,30 (2) 3,57 km/h
Reverse speed (km/h)
2,18 km/h
Cutting width
600 mm
Height of cut
55 à 70 mm
Weight
98 kg
CHECK LIST
INSTRUCTIONS TO THE DEALER
• The assembling, the installation and the first application of the machine is under the DAISHIN
dealer’s responsability.
• Read the instruction manual as well as the safety measures. Check that all the before delivery and
at delivery check points specified in the following lists have been verified and possibly modified
before delivering the machine to its owner.
CHECKS BEFORE DELIVERY
• Check that all the shields, grids and safety guards are in place and in a good state.
• Check that the hydraulic hoses are in place and in a good state. Replace them if necessary.
• Check that there is no oil leak, repair if necessary.
• Check that the safety instruction stickers are in place and in a good state. Replace them if
necessary.
• Check that all the bolts and screws are properly tightened with the right torque (refer to th torque
chart).
•Protect the grease nipples by coating them with grease and lubricate the machine.
•Check that the machine can work properly.
CHECKS ON DELIVERY
•Show the user how to perform the adjustments.
• Explain to the user the importance of the lubrication and show him the different greasing points on
the machine.
•Show him the safety devices, grids, guards and the optional equipments.
•Give the instruction manual to the customer, ask him to read it carefully.

DAISHIN SRM180K Page 5
SAFETY RULES
CAUTION
Some of the illustrations show the machine with no guard, no shield. Never use the machine
without these devices.
•Learn to stop the machine in case emergency.
•Read this manual.
•Do not let anybody use the machine before having read and understood this
manual.
•Do not let children use the machine.
•Do not wear loose clothes. They might be grasped by moving parts.
•Always wear protection equipments for when using the machine.
•Only work during daylight or with a good artificial light.
•Check that the safety instruction stickers are in place and in a good condition.
•Keep the machine free from debris or mud.
•Check that the machine can work properly before any use.
•Check that all the shields, grids and safety guards are in place and in a good state.
•It is strictly forbidden to carry persons or animals onto the machine during the work or during the
transportation.
•Never stop or start roughly when working on a slope. Never use the
machine to work on a stepping terrain.
•Reduce the ground speed when running on a slope and when turning
straight in order to prevent from any risk of losing control.
•Be very careful when bordering ditches.
•Stop the engine, and remove the sparking plug ignition cover before any
intervention on the machine.
•Never work under the machine or its parts when lifted, unless they are
blocked and maintained into position with sufficient security.
•When running on a slope, always work going up or down but never
across the slope.
•Steer clear of unsteady embankments, holes or rocks. They might be dangerous during
manœuvres or transport.
•Keep away from electric wires and obstacles. A contact with electric wires cause electrocution and
death.
•Stop the machine progressively when lifting or lowering the machine.
•When stopping the work, stop the engine and remove the sparking plug ignition cover before
leaving the mower.
•Engage all the safety equipments.
•Move the controls only when correctly sat down in the mower
•Visually check hydraulic leaks and if some parts are faulty or missing. Repair before use.
•Never change the adjusment of the regulator, it is set in the factory. Unsetting this valve would
cause failures.
•Ensure that the user of the machine has already read and understood this
manual and that he is aware of all the safety instructions before any use.
•Always use a chuck and bronze hammer when replacing or intervening on
the pins and bolts at the end of rams, rod … etc in order to avoid the
projection of metal fragments.

DAISHIN SRM180K Page 6
DIFFERENT PARTS OF THE MOWER
Figure 1
Left
Front
Right
Rear
Handle
adjiustment
Starter
Height of cut
adjustme
Front
wheel
Front skirt
Handle
Fuel cap
Air filter
Fuel tank
Deck
Shift lever
main clutch
Throttle lever
Differential
locking lever
Clutch of braid
Assist clutch
of braid
Parking brake
Oil cap

DAISHIN SRM180K Page 7
SAFETY INSTRUCTION STICKERS
Note their location and replace them immediately in case of damage or when they are missing
Keep away hands and feet from
rotating blades
Read owner’s manual
Beware of thrown objects
Keep away from the machine
Unplug sparking wire before
maintenance
Beware of rotative belts
under the shield
Keep away hands and feet from
rotating blades
Do not exceed 15° slopes
M A D E I N
JAPAN
M O D E L : S R M - 1 8 0 K
M A X . P O W E R : 4 .5 k W
E N G IN E R E
V. : 3 2 0 0 m in
D
RY
W E I G H T: 98 k g
Always wear protective equipment
against noise, dust and gogles
This machine comply with
EC regulation
Performance label

DAISHIN SRM180K Page 8
Beware of rotative belts under
the shield
Read owner’s manua.
Beware of flammable liquids.
Beware of exhaust gases.
Beware of hot surfaces

DAISHIN SRM180K Page 9
CONTROLS
TRAVEL LEVER
Push the lever forward to the handlebar, to make the machine moving. Release the lever, then the
machine stops.
SPEED LEVER
This lever allowed to change the travel speed from 1 (low speed) to 3 (high speed). Put the lever on
“R” to go on reverse. (1, figure 3). (N) position is neutral.
Always change travel speed when machine is stopped.
DIFFERENTIAL LOCKING LEAVER.
This lever allowed the rear wheels to be drived together in slipping area. The diff lock should be used
in straight line only, not when turning. (3, figure 2)
THROTTLELLVER AND CHOKELEVER
(4, figure 2)
Push the lever completely forward to operate the choke to start cold engine, when engine has start
release it. Push the throttle lever forward to « HI » to increase engine speed, pull the throttle lever
rearward to « LO » to decrease engine speed to idle rpm. Always operate mower at full engine speed.
Pull the throttle lever rearward to « STOP » to stop the engine
IMPORTANT
Do not use the choke when the engine is hot, it did not start
BRAKE LEVER
The brake lever is located on the right side of the handlebar. This lever is working with the travel lever.
When travel lever is released the brake is locked. Lock the lever when machine is stopped unatended
even in flat areas. (1, figure 5).
CUTTING BLADE CLUTCH LEVER
Cutting blade Clutch lever make the engine drive the blade to mow (2, Figure 2, ). Pull the lever
rearward to the handlebar to make the blade turning. Release the lever, then the blade stops.
Never try to start or stop the engine with blade engaged
Figure.2

DAISHIN SRM180K Page 10
FUEL VALAVE
The fuel cock is closed when machine is not use.
Fuel cock is closed pushed rearward, and open
forward. (1, Figure 3)
Figure 3
HEIGHT OF CUT CONTROL
Height of cut can be setted by turning the bar A Figure 7, clockwise to increase the height of cut and
anti- clockwise decrease the height of cut.
Always perform this adjustment engine off and sparking
plug cover unplugWhen cutting in low position, power
needed and thrown objects are more important. Cutting
low can cause damage to the machine and injury.
Figure 4
Figure 4

DAISHIN SRM180K Page 11
OPERATION
Check the tightening of bolts, refering to the tightening torque charts
The user of this machine is responsible for its safe use. He must be a skilled user specially trained for
the use of this machine. Read the safety instructions. This machine has been designed to mow grass.
It is not designed for any other operation. It is no designed to transport other tools or materials that
might damage it and cause injuries to the user. It must not be used to carry persons.
Never use the machine without having priorly carried out all the maintenance operations as
described in the daily maintenance chapter.
Never let children or unskilled persons use the machine. Check that nobody or no object
stands near the machine when at work. They could be hit by the moving parts.Nobody must
stand on the machine except the driver. Never put your hands under moving parts.
STARTING OF THE ENGINE
• Turn the fuel cock "ON" and seat down at operator’s place.
• Check than cutting blade is disengaged, and travel lever in neutral position « N ».
• Pull choke lever if engine is cold or push throttle lever half if engine is hot. Press the brake lever
and pull the starter rope. When the engine has started, push back the choke lever.
MOWING
•Adjust the height of cut control bar as needed.
Do not forget that it is better to mow a few grass often than an important quantity in one
operation. Short grass do not resist to dry weather, and athe blade can hit the grown with
damage and trhown objects. Working in slopes is very dangerous. Never work in slopes more
than 16°.
• Push the cutting blade control lock close the handlebar (7, Figure 2) and pull the lever (6) backward,
then pull the travel lever and go forward in the grass to mow.
• The best cutting speed depends of quantity and the density of the grass. Usually it is asked to mow
between 2,5 and 6 Km/H. A tall grass will be cut slowly and a low grass will be cut faster.
Do not forget that it is better to mow a few grass often than an important quantity in one
operation. Short grass do not resist to dry weather, and the blade can hit the grown with
damage and trhown objects.
HOW TO STOP THE MACHINE
• Release travel speed lever and blade clutch lever.
• Pull backward the throttle lever to stop.
• Close the fuel cock
• Lock the parking brake lever
Never park the machine on slopes. Stop it on a level and flat surface.
STORING THE MACHINE
Thoroughly clean the machine. Use touch up paint to prevent rust. Check for worn and damage parts,
install new parts as required. Preform the normal maintenance of the machine according to
maintenance chart. Store the machine in a dry protected area. Remove sparking ignition wire from
the sparking plug.
The safety was one of our main worry when designing and manufacturing this machine.
Therefore, negligence in the use of the machine should reduce our efforts to nothing. The
prevention strictly depends on the care and on the skill of the user when applying and
maintening the machine.The best safety method remains a careful and skilled user ; we
wish you to be this kind of user.

DAISHIN SRM180K Page 12
MAINTENANCE OPERATION TOBE CARRIED OUT BY THE USER
BEFORE perform any maintenance operation on the machine, cut off the engine, and remove
the sparkin wire from the sparking plug
If maintenance operation are not realized, damages can occur to the machine and personnal injuries
to the user and/or spectators. These damages and injuries will not be covered by the warranty.
•Daily maintenance will be performed by the user.
•Maintenance opérations for first 20 hours, 100 et 300 should be realized by the dealer.
•Ask your dealer to check the machine if you meet some problems.
•Ask your distributor the name of your dealer.
DAILY MAINTENANCE,BEFORE START MOWING
Oil level : check by the gauge (A figure 9). Oil level should appear in the middle of the window. when
the gauge is put on his place without screwing it (figure 13). Check only engine stopped since ten
minutes on a flat level surface.
•Use only good quality gear oil 80W90 API GL4.
•Ask to your dealer to change oil once a year.
FUEL
(Figure 10, repère 1)
Check tank level is full before start to work. Check that tank cap is fully closed, and check for leaks.
Use only a good quality unleaded gasoline.
Check fuel tank is closed, wipe fuel spillages before start the machine. Check there is no fire,
electric sparks, cigarettes near the machine when refuelling.
TIRES
Check tires are not cutted, cracked or worn.
•Check tires pressure : 1,2 bar front and 1,4 bar rear.
SAFETY STICKERS
•Check safety stickers are sticked at their place. Replace
them if they are worn and damage.
BLADE AND BLADE HOLDER CONDITION
You can be cutted and injuried by cutting blade. Always wear gloves when holding blades.
Check rotary blades are in good condition, change worn or damage parts.
Changing blade : unscrew hexagonal screws and washer from the blade holder.
Check the blade condition. Change it if it is worn bend or crackle.
Check thightening of hexagonal screws according to the chart at the end of the manual.
Sharpen as shown in C, follow the angle of 30-40°, keep a sharpen hedge of 0,4 to 0,6 mm.
Always keep 30 mm of width.

DAISHIN SRM180K Page 13
Only use original genuine DAISHIN parts. Other parts may be dangerous for your health and
for the bystanders and the machine.
If some vibration occur or/and If you feel vibrations in the handlebar, check the blade or made
it checked by your dealer. Vibrations may cause loosening of the bolt and nuts and may crack
the steel of the machine.
LUBRICATION:
Lubricate the control pivot axle, blade brake axle and wires with light oil.
Grease the front wheel axle (A figure 7) with grease NLGI N°2.
AIR FILTER:
Dismount the air filter by sliding the key (1 figure 9) backward and pulling the cover.
Pull the paper cartridge and the foam (Figure 10 & 11)
Foam filter :
Clean the foam with water and soap. Dry the foam, and oil slightly with engine oil, press the oil in
excess without twisting.
Paper:
Blow the cartrige "C"with low air pressure from the inside to the outside, oposite to the normal air flow.
Change the cartridge if it is too dusty or after five cleaning.
Reassemble througly the air filter system
ENGINE:
Refer to engine manual deliver with the machine.
Engine oil level:
Unscrew the dipstick (1, figure 12) Clean it and put it on the engine without screwing it. Check the oil level, it
must be on the A & B. Add oil if it is required with gasoline engine oil SAE 10W30 API SF or SG.
Figure 8
Figure 10
Figure 11
Figure 9
Figure 7
Figure 12
Figure 13

DAISHIN SRM180K Page 14
MONTHLY MAINTENANCE
Transmission wire adjustment:
If the machine does not move or if the transmission belt slips when transmission lever is pressed,
adjust the tension wire as follow : unscrew the locking screw (1 figure 14) and increase the wire
tension. Try to move the machine again. Perform the adjustment again if needed.
If the machine move when transmission lever is released, adjust the tension wire as follow : unscrew
the locking screw and decrease the wire tension. Try to stop the machine again. Perform the
adjustment again if needed.
Blade wire:
If the blade does not stop when the blade lever is released, adjust the tension wire as follow :
unscrew the locking screw (2 figure 14) and and decrease the wire tension. Try the machine again.
Perform the adjustment again if needed.
If the blade does not move when transmission lever is pressed, adjust the tension wire as follow :
unscrew the locking screw increase the wire tension. Try the machine again. Perform the adjustment
again if needed.
Differential locking wire :
If the locking does not engage when the lever is pressed, adjust the tension wire as follow :
To increase the tension wire : unscrew the locking screw (1 figure 15) and increase the wire tension.
Try the machine again. Perform the adjustment again if needed.
To loosen the tension wire : unscrew the locking screw and decrease the wire tension. Try the
machine again. Perform the adjustment again if needed.
Figure 14
Figure 15

DAISHIN SRM180K Page 15
Belt maintenance :
A loose belt slips and involve loss of power. An overtighten belt involve a fast wear of
bearings.
Check belt tension and condition after the first 3 hours of use and every week. Check if the belets are not loose,
overtighten or cracked. Replace the belts as necessary
Oil level:
Check by the gauge (1 figure 16). Unscrew the cap, the level should be at the opening. Check only
engine stopped since ten minutes on a flat level surface.
Use only good quality gear oil SAE 80W90 API GL4.
Ask to your dealer to change oil once a year.
Figure 16
1

DAISHIN SRM180K Page 16
MAINTENANCE CHART
Ask your dealer to realize this operation needing special tools and knowledge.
Inspection to realize by the owners before starting the engine
Inspection to realize by the owners after starting the engine
Part to inspect
Inspection
Every
use
first 20
hours
Every les
100
hours
Every 300
hours every
year
Blade belt
Check belt tension


Check wear


Fuel
refuelling

Fuel cock

Flammables matérials
Clean the machine from flammables
matérials

Travel lever
check machine do not move when
lever is on “N”

Check travel lever goes on “N” when
applying brake

Tyres
Check tires pressure

Check tires wear

Brake
Check efficiency of the brake

Check travel lever goes on “N” when
applying brake

Châssis
Check for rust, and cracks
Safety stickers
Check they are in place and in good
condition

Safety switches
Check for efficiency

Guards & shields
Check they are bolted in their place
and in good condition

Tank and fuel hoses
Check for leaks and good condition
Replace if needed

Throttle lever
Check for efficiency

Blades
Check they are bolted in their place
and in good condition

Blade clutch control
lever
Check the adjustment of the wire



Blade brake
Check the adjustment



Blade belt
Check they tensionned and in good
condition


Engine
Refer to engine manual

DAISHIN SRM180K Page 17
BREAKDOWNS AND SOLUTIONS
PROBLEME
CAUSE
SOLUTIONS
No fuel
Refuel the tank
Battery is empty
Load or replace the battery
Engine does not start
Safety switches are working
Check brakes, blade clutch and seat
and travel lever
The machine does not travel
Parking brake is locked
unlock parking brake
The machine does not stop
Travel lever is not on « N »
Move the travel lever to « N »
The blade does not rotate
Blade clutch lever is not
engage
engage Blade clutch lever
Safety switches are working
Check brakes, blade clutch and seat
and travel lever
TIGHTENING TORQUES (daNm)
Diameter of
SPANNER
Mark on the screw head
the screw(mm)
SIZE (mm)
8.8
10.9
8
13
2.5
3.5
10
16
5
7.5
12
18
8.5
13
14
21
12.87
18.11
16
24
21.5
31.5
18
27
26.6
37.4
20
30
43.5
62
22
32
51
71.71
24
36
75
107
30
46
149.5
213

DAISHIN SRM180K Page 18
LIMITED WARRANTY
Each new product manufactured by DAISHIN is guaranteed under the cope of the following terms. The warranty
applies to defective parts due to defect in assembling and construction or/and in material imputable to us. It is
valid for a period of one year and for normal use of the machine. It does not apply to engines manufactured by
other companies that also guarantee their materials and whose guarantee is supplied with the machine.
1° This guarantee is limited to the sole replacement of the defective parts during one year commencing with the
purchasing date of the machine. The guarantee is limited to the parts that are previously shown to and acknowl-
edged by DAISHIN.
2° Each part concerned by a guarantee claim must be returned to DAISHIN’s in order to be inspected, repaired
or replaced. The part(s) must be returned with freight prepaid and must be accompanied with a proof of the pur-
chase. The part(s) must be packed with the greatest of care to ensure their protection.
3° The machine must not have been worn out, repaired or maintained by anyone without DAISHIN’s previous
authorization. The machine must not have been damaged in a road accident, roughly handled or unproperly
used.
This guarantee does not involve DAISHIN or its dealer to reimburse the labour costs or the carriage costs to the
repairer.
NO OTHER GUARANTEE SHALL BE APPLIED TO THIS MACHINE EXCEPT THE LEGAL GUARANTEE.
DAISHIN SHALL NOT BE LIABLE FOR ANY DAMAGE OR COST INVOLVED BY THE MACHINE, FOR EX-
AMPLE : 1. HIRING COSTS
2. TURNOVER LOSSES
3. WORK DONE BY A REPLACING MACHINE
DAISHIN DOES NOT TAKE ON ANY OTHER OBLIGATION AND DOES NOT AUTHORIZE ANYBODY TO
TAKE ON ANY OTHER OBLIGATION THAN THOSE MENTIONED IN THE 3 PARAGRAPHS ABOVE.
To know the name of your dealer, report to: DAISHIN
www.daishin-japan.co.jp

DAISHIN SRM180K Page 19
INTRODUCTION
Toute l’équipe DAISHIN vous félicite pour votre choix de la tondeuse débroussailleuse SRM 180K. Lisez ce
manuel avant d’utiliser votre tondeuse débroussailleuse, les informations qu’il donne vous permettront
d’effectuer un travail de qualité en toute sécurité. Conservez-le à portée pour vous en servir de référence.
Demandez un autre manuel à votre revendeur s’il est perdu ou abîmé.
La sécurité dans l’emploi de cette machine dépend de la manière dont elle est utilisée avec les limitations
expliquées dans ce manuel. Vous devez connaître et suivre toutes les règles de sécurité de ce manuel et de la
tondeuse débroussailleuse.
La tondeuse débroussailleuse DAISHIN SRM-180K que vous avez acheté a été soigneusement conçue et
fabriquée pour vous donner toute satisfaction. Comme tout engin mécanique, elle nécessite du nettoyage et de
la maintenance. Lubrifiez-la comme indiqué. Suivez les règles et les informations de sécurité données dans ce
manuel et sur les autocollants de sécurité de la tondeuse débroussailleuse.
Pour l’entretien, seul votre revendeur DAISHIN possède la compétence, les pièces d’origine DAISHIN et les
outils nécessaires pour répondre à vos besoins.
Utilisez exclusivement les pièces d’origine DAISHIN, les pièces « adaptables » n’ont pas le niveau de qualité
nécessaire pour que la machine fonctionne correctement et en toute sécurité ; de plus, elles rendaient la
garantie caduque. Inscrivez ci-dessous le modèle et le numéro de série de votre machine :
MODELE :.........................................................
N° DE SERIE :.................................
Donnez cette information à votre revendeur pour obtenir les bonnes pièces.
Dans un souci de progrès constant, DAISHIN se réserve le droit de modifier ses machines sans pour cela être
tenu d’apporter ces modifications aux machines déjà vendues.
Les illustrations et caractéristiques de ce manuel peuvent varier légèrement sur votre machine en fonction de
modifications apportées à la production.
Tout au long de ce manuel, la gauche et la droite ainsi que l’avant et l’arrière sont déterminées en étant au poste
de travail.
Le terme IMPORTANT est utilisé pour indiquer qu'une défaillance peut entraîner des dommages à la machine.
Les termes AVERTISSEMENT, ATTENTION et DANGER sont utilisés avec le symbole alerte sécurité (un
triangle avec un point d'exclamation) pour indiquer le degré de danger pour votre sécurité.
Ce symbole veut dire: attention, soyez attentif, votre sécurité est en jeu. Il rappelle les consignes de sécurité ou
porte votre attention sur les pratiques dangereuses pouvant provoquer des blessures.
AVERTISSEMENT
Attire votre attention sur un rappel des règles de sécurités pouvant causer des
blessures si elles ne sont pas observées.
ATTENTION
Attire votre attention sur un danger existant pouvant provoquer des
blessures ou la mort si des précautions appropriées ne sont pas prises.
Attire votre attention sur un danger très important qui entraînera certainement des
blessures irréparables ou la mort si les bonnes précautions ne sont pas prises.

DAISHIN SRM180K Page 20
CARACTERISTIQUES
Modèle
SRM-180K
Dimensions ( L x l x h en mm )
2,030 x 705 x 1,100
Largeur de coupe (mm)
600
Vitesse avant 1 (km/h)
2,30
Vitesse avant 2 (km/h)
3,57
Vitesse arrière (km/h)
2,18
Poids (kg)
98
Transmission
par courroie et poulie
Embrayage de la coupe
par tension de courroie
Hauteur de coupe (mm)
30 à 70
Capacité de coupe (m²/h) Vit.1
1 380
Capacité de coupe (m²/h) Vit. 2
2142
Moteur
KAWASAKI FJ180V
4,5 kW
(6.0 HP)
LISTE DES VERIFICATIONS
AU CONCESSIONNAIRE REVENDEUR
 Le montage, l’installation et la mise en route de la tondeuse débroussailleuse est la responsabilité du
revendeur DAISHIN.
 Lisez le manuel d’utilisation et d’entretien ainsi que les règles de sécurité.
 Vérifiez que les points indiqués sur les listes de vérifications avant livraison et à la livraison ont tous étés
vérifiés et éventuellement corrigés avant de laisser la machine à son propriétaire.
VERIFICATIONS AVANT LIVRAISON
 Vérifiez que tous les écrans, grilles et garants de sécurité sont en place et en bon état.
 Vérifiez que les déflecteurs en sortie de tondeuse débroussailleuse sont en place et en bon état.
Remplacez-les si nécessaire.
 Vérifiez que les autocollants de sécurité sont en place et en bon état. Remplacez-les si nécessaire.
 Vérifiez que tous les vis et boulons sont serrés au bon couple (voir tableau en fin de manuel).
 Garnissez les graisseurs et lubrifiez la machine.
 Vérifiez que la machine fonctionne correctement.
 Vérifiez l’état des courroies et de la transmission.
VERIFICATIONS A LA LIVRAISON
 Montrez au client comment réaliser les réglages.
 Expliquez-lui l’importance de la lubrification et montrez-lui les points de lubrification sur la machine.
 Montrez-lui les dispositifs de sécurité, grilles, garants, déflecteur ainsi que les options.
 Présentez au client le manuel d’utilisation et d’entretien, demandez-lui de bien le connaître.

DAISHIN SRM180K Page 21
REGLES DE SECURITE
* Lisez et respectez les règles de sécurité écrites dans ce manuel, votre revendeur vous les
expliquera si vous en faites la demande.
* Essayez d'abord la machine sur une surface plate et vaste.
* Gardez ce manuel à portée de main et en bon état, cela évitera des accidents par
méconnaissance des règles. Assurez-vous que toute personne qui utilise la machine ai lu et
compris ce manuel.
ATTENTION
Quelques illustrations peuvent montrer la machine dépourvue d’écrans, de boucliers,
N’utilisez jamais la machine sans ces dispositifs.
* Apprenez à arrêter la machine en cas d’urgence. Lisez ce manuel et celui livré avec la tondeuse
débroussailleuse.
* Portez toujours des vêtements ajustés qui éviteront d’être happés par les
pièces en mouvement.
* Portez toujours des équipements de protection pour la tête, les yeux, les
oreilles, les mains et les pieds lorsque vous utilisez cette machine.
* Travaillez exclusivement à la lumière du jour ou avec une bonne lumière
artificielle.
* Vérifiez que les autocollants de sécurité sont en place et en bon état.
*Nettoyez les accumulations d’herbe ou de débris.
* Vérifiez que la machine est en bonne condition de travail avant de l’utiliser.
* Vérifiez que tous les écrans, grilles, sont en place et en bon état.
* Ne fumez pas lorsque vous faites le plein de carburant. Utilisez toujours de l'essence sans plomb. Le non
respect de ces consignes peut provoquer un incendie ou des dommages au moteur.
* N’utilisez pas la machine dans des zones ou vous ne pouvez pas maintenir les personnes ou les animaux à
une distance telle qu’ils ne puissent être atteints par des projections.
* Ne pas démarrer ou s’arrêter brutalement dans les pentes. N’utilisez pas la machine dans les pentes en
escalier.
* N’autorisez pas les enfants à utiliser cette machine.
* Réduisez votre vitesse dans les pentes et lorsque vous tournez court pour éviter les pertes de contrôle.
* Soyez prudent lorsque vous longez des talus ou des fossés.
* Nettoyez le chantier des branches, pierres ou débris qui peuvent être
projetés en causant des blessures ou des dommages.
* Faites attention aux trous ou autres accidents de terrain lorsque vous
travaillez dans des terrains accidentés.
* Débrayez la lame, arrêtez le moteur, fermez l’alimentation en carburant,
enlevez l'anti-parasite avant d’effectuer tous réglages, entretien ou démontage sur la machine.
* N’autorisez personne au poste de conduite lorsque vous effectuez des réglages, entretien ou démontages sur
la machine.
* Ne changez pas les réglages du moteur de la tondeuse débroussailleuse, n’emballez pas le moteur.
* Vérifiez périodiquement le serrage de toute la boulonnerie.

DAISHIN SRM180K Page 22
DESCRIPTION DE LA MACHINE
Figure 1
Gauche
Avant
Droite
Arrière
Réglage du
mancheron
Lanceur
Réglage
hauteur
de coupe
Roue
Avant
Déflecteur
Avant
De manette
Robinet de
carburant
Filtre à ai
Réservoir de
carburant
Tablier
de coupe
Levier de
changement
Levier
d'embrayage
principal
Levier de la
commande de
vitesse
Levier de
différentiel
Levier de
lame embrayage
L'assistance du
levier de
lame embrayage
Frein à main
Robinet de
huiler