Daktronics SW-2101 User manual

201 Daktronics Drive
Brookings, SD 57006-5128
www.daktronics.com/support
800.325.8766
AQUATICS/TRACK LED
SCOREBOARDS
DISPLAY MANUAL
P1153
DD3043167
Rev 03
24 February 2021
Models
SW-2101 SW-2216 SW-2008
SW-2106 SW-2118 SW-2009
SW-2108 SW-2220 SW-3104
SW-2110 SW-2001 SW-3108
SW-2116 SW-2002 SW-3118
SW-2118 SW-2003
SW-2120 SW-2004
SW-2206 SW-2005
SW-2208 SW-2006
SW-2210 SW-2007

Copyright © 2015-2021
All rights reserved. While every precaution has been taken in the preparation of this manual, the publisher assumes no
responsibility for errors or omissions. No part of this book covered by the copyrights hereon may be reproduced or copied
in any form or by any means—graphic, electronic, or mechanical, including photocopying, taping, or information
storage and retrieval systems—without written permission of the publisher.
Daktronics trademarks are property of Daktronics, Inc. All other trademarks are property of their respective companies.
FCC Statement
Supplier Declaration of Conformity (SDoC)
This product complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Note: This equipment has been tested and found to
comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference when the equipment is operated
in a commercial environment. This equipment
generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance
with the instruction manual, may cause harmful
interference to radio communications. Operation of
this equipment in a residential area is likely to cause
harmful interference in which case the user will be
required to correct the interference at their own
expense.
Warning: The user is cautioned that changes and
modications made to the equipment without the
approval of manufacturer could void the user’s
authority to operate this equipment.
Industry Canada Regulatory Information
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à
la norme NMB-003 du Canada.
Inquiries
Contact Daktronics with any questions regarding our
product compliance.
Mail:
Daktronics
201 Daktronics Dr.
Brookings, SD 57006 USA
Phone:
800-325-8766
Website:
www.daktronics.com

– i –
Table of Contents
1 Introduction���������������������������������������������������������������������������������������������������������������������������1
Important Safeguards ..........................................................................................................................1
Specications Label .............................................................................................................................1
Model Descriptions...............................................................................................................................1
Resources ..............................................................................................................................................2
Daktronics Nomenclature ...................................................................................................................2
Display Controllers ................................................................................................................................3
Product Safety Approval .....................................................................................................................3
2 Mechanical Installation �������������������������������������������������������������������������������������������������������4
Installing Caption Modules..................................................................................................................4
Wall Mounting Digit Modules ..............................................................................................................5
SW-3104���������������������������������������������������������������������������������������������������������������������������������������������5
Vertical Wall Mounting (Indoor or Outdoor) ����������������������������������������������������������������������������������5
Horizontal Wall Mounting (Indoor Only)�����������������������������������������������������������������������������������������6
Corner-Mounting (Indoor Only) ������������������������������������������������������������������������������������������������������6
Beam Mounting (Outdoor)..................................................................................................................7
3 Electrical Installation ������������������������������������������������������������������������������������������������������������8
Indoor Scoreboard Power ...................................................................................................................8
Grounding �����������������������������������������������������������������������������������������������������������������������������������������8
Power Connection����������������������������������������������������������������������������������������������������������������������������8
Outdoor Scoreboard Power ...............................................................................................................9
Grounding �����������������������������������������������������������������������������������������������������������������������������������������9
Installation with Ground and Neutral Conductors Provided ....................................................9
Installation with Only a Neutral Conductor Provided..............................................................10
Lightning Protection������������������������������������������������������������������������������������������������������������������������10
Installing Load Centers ������������������������������������������������������������������������������������������������������������������10
Connection �������������������������������������������������������������������������������������������������������������������������������������10
Power-On Self-Test (POST)..................................................................................................................11
Indoor Signal Connection .................................................................................................................12
Outdoor Signal Connection..............................................................................................................12
Wireless Signal Connection ...............................................................................................................13
Internal Cable Routing (Horizontal Models Only) ...........................................................................13
Setting the Driver Address..................................................................................................................13
4 Troubleshooting ������������������������������������������������������������������������������������������������������������������17
Troubleshooting Table........................................................................................................................17
Component Locations & Access......................................................................................................19
Replacing Digits..................................................................................................................................19
Segmentation & Digit Designation ...................................................................................................20
LED Drivers ...........................................................................................................................................20
Replacing a Driver��������������������������������������������������������������������������������������������������������������������������21
Radio Connections.............................................................................................................................21
Radio Interference��������������������������������������������������������������������������������������������������������������������������22

– ii –
Table of Contents
Schematics..........................................................................................................................................22
Replacement Parts.............................................................................................................................23
5 Daktronics Exchange and Repair & Return Programs ����������������������������������������������������24
Exchange Program ............................................................................................................................24
Repair & Return Program...................................................................................................................25
Daktronics Warranty & Limitation of Liability ...................................................................................25
A Mechanical Drawings ��������������������������������������������������������������������������������������������������������27
B Electrical Drawings �������������������������������������������������������������������������������������������������������������51
C Daktronics Warranty & Limitation of Liability��������������������������������������������������������������������79

Introduction
1
1 Introduction
This manual explains the installation of Daktronics Aquatics/Track LED Scoreboards. For
additional information regarding the safety, installation, operation, or service of these
displays, refer to the telephone numbers listed in Section 5: Daktronics Exchange and
Repair & Return Programs (p�24). This manual is not specic to a particular installation.
Important Safeguards
• Read and understand all instructions before beginning the installation process�
• Properly ground the cabinet with a grounding electrode at the display location�
• Disconnect the display power when not in use or when servicing�
• Disconnect the display power before servicing power supplies to avoid electrical
shock� Power supplies run on high voltage and may cause physical injury if touched
while powered�
• Do not modify the structure or attach any panels or coverings to the display without
the express written consent of Daktronics�
• Do not disassemble control equipment or electronic controls of the display; failure to
follow this safeguard will make the warranty null and void�
• Do not drop the control equipment or allow it to get wet�
Specications Label
Power specications as well as serial and model number information can be found on an
ID label, similar to the one shown in Figure 1.
DAKTRONICS 201 DAKTRONICS DR. BROOKINGS, SD PHONE [phone]
SUITABLE FOR SERVICING ONLY WHEN DE-ENERGIZED
PUET FAIRE L'OBJET D'UN ENTRETIEN UNIQUEMENT S'IL EST HORS TENSION
LL-4284957
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO
THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED,
INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION
Figure 1: Specications Label
Please have the assembly number, model number, and the date manufactured on hand
when calling Daktronics customer service to ensure the request is serviced as quickly as
possible. Knowing the facility name and/or job number will also be helpful.
Model Descriptions
Reference Drawings:
Module Model Descriptions .............................................................................. DWG-129639
Model Congurations, Swim / Track Timing..................................................... DWG-130101
Model Congurations, Aquatics Multisport ..................................................... DWG-130102
To determine which pieces make up what model and how they are arranged, refer to
DWG-130101 and DWG-130102 in Appendix A. Refer also to DWG-129639 for detailed
views of each display piece and add-on modules.

Introduction
2
Resources
Figure 2 illustrates a Daktronics drawing label.
This manual refers to drawings by listing the last
set of digits. In the example, the drawing would
be referred to as DWG-1007804. All references to
drawing numbers, appendices, gures, or other
manuals are presented in bold typeface. Any
drawings referenced in a section are listed at the
beginning of it as shown below:
Reference Drawings:
System Riser Diagram....................................................................................... DWG-1007804
Daktronics identies manuals by the DD or ED number located on the cover page.
Listed below are drawing types commonly used by Daktronics, along with the information
typically provided. All drawings referenced in this manual are found in the appendices.
• Schematic Drawings: describe internal power and signal wiring as well as
interconnections between display sections; they may also include digit designations
and driver addressing information
• Shop Drawings: describe mounting methods to structural elements, access method
(front or rear), and power and signal entrance points
• System Riser Diagrams: describe power/signal connections between components
and the control location; they may also include control room layout and schematic
• Final Assembly Drawings: describe internal component locations and detailed
product appearance with part numbers and quantities
Project-specic information takes precedence over any other general information found
in this manual. Ensure all applicable material has been gathered before beginning the
installation. Contact a Daktronics sales coordinator or project manager.
Daktronics Nomenclature
Most display components have a white label that lists the part
number (Figure 3). Part numbers will also appear on certain drawings.
If a component is not found in the Replacement Parts (p�23), use
the label to order a replacement. Refer to Section 5: Daktronics
Exchange and Repair & Return Programs (p�24) if replacing or
repairing any display component.
Main Component Labels
Part Type Part Number
Individual circuit board 0P-XXXX-XXXX
Assembly; a collection of
circuit boards 0A-XXXX-XXXX
Wire or cable W-XXXX
Fuse F-XXXX
Transformer T-XXXX
Metal part 0M-XXXXXXX
Fabricated metal assembly 0S-XXXXXX
Specially ordered part PR-XXXXX-X
Drawing Number
Figure 2: Drawing Label
0P-1127-0024
SN: 2465
02/19/12 Rev. 1
Figure 3: Part Label
Accessory Labels
Component Label
Termination block for
power or signal cable TBXX
Grounding point EXX
Power or signal jack JXX
Power or signal plug for
the opposite jack PXX

Introduction
3
Display Controllers
The OmniSport 2000 timing console uses keyboard overlays (sport inserts) to control
numerous sports and display models. Refer to the manual below for operating
instructions. The manual is provided on a CD with the control consoles, and also available
online at www.daktronics.com/manuals.
• OmniSport 2000 Timing Console Operation Manual (ED-13312)
It is also possible for these displays to be controlled via third-party timing consoles, such
as those produced by Omega and Colorado Timing Systems (CTS). In these cases, refer
to the documentation provided by the manufacturer.
Product Safety Approval
Daktronics outdoor displays are ETL-listed and tested to CSA standards for outdoor use.
Contact Daktronics with any questions regarding testing procedures.

Mechanical Installation
4
2 Mechanical Installation
Refer to the electrical installation drawing before beginning the mechanical installation
procedure� It is important to recognize where the electrical wires are located so
knockouts can be removed respectively before the display has been mounted� It will be
easier to install electrical hookup items, route conduits, and attach hookup boxes before
mechanical installation�
• For indoor scoreboards, mechanical installation typically consists of lifting and
permanently mounting the scoreboard to a wall. The mechanical specication
drawings listed in Appendix A show the recommended number and spacing of wall
anchors for indoor scoreboard models.
• For outdoor scoreboards, mechanical installation typically consists of installing
concrete footing and steel beams and mounting the scoreboard to the beams. The
columns, footings, and all connection details must be designed and certied by a
professional engineer licensed to practice in the state of the scoreboard installation.
Be sure that the installation complies with local building codes.
Note: Daktronics assumes no liability for any installation derived from the information
provided in this manual or installations designed and installed by others.
Installing Caption Modules
Reference Drawings:
Caption Layout- 6-Lane Multi-Sport Systems................................................... DWG-130319
Caption Layout- 8-Lane Multi-Sport Systems................................................... DWG-130321
Caption Layout- 10-Lane Multi-Sport Systems................................................. DWG-130801
Caption Module Detail ...................................................................................... DWG-130840
Note: Attach the caption module to the digit module before attaching the digit
module to the wall.
The caption modules are attached to the top or bottom of a digit module with #10
machine screws (refer to DWG-130840). Before attaching the caption module, note its
orientation. The top and bottom guides for holding the caption panel are different sizes.
Be sure the module is oriented so that the deeper guide is toward the top.
To insert a caption panel, t the top edge of the caption panel into the module's upper
guide, and then slide the bottom edge under the lower guide (refer to DWG-130840). The
construction of the guides allows the caption panels to be lifted out for changing, rather
than having to slide them out one end.
The caption panels must be properly positioned in relation to the scoreboard digits for
different activities. Refer to DWG-130319, DWG-130321, and DWG-130801 for caption
layouts. The drawings indicate the proper location of the digits and caption panels that
will be used for the various events and sports.

Mechanical Installation
5
Wall Mounting Digit Modules
Due to the variety of wall materials used in sports facilities, Daktronics cannot anticipate
a user’s individual installation needs or provide mounting hardware suitable for every
installation. Choose a method of installation that will safely support the weight of the
display.
Before installing any wall anchors or the mounting structure, determine where all of the
mounting holes will be located on the display modules. Holes provided on the modules
should be convenient for most installations.
For mounting locations, weights, and hardware suggestions, refer to the model-specic
mechanical specication drawings listed in Appendix A.
SW-3104
Reference Drawings:
SW-3104 Floor Stand Assy................................................................................... DWG-253540
The SW-2104 features carrying handles and may not need to be wall mounted. However,
it may be mounted to a oor stand for greater stability. Refer to DWG-253540.
Vertical Wall Mounting (Indoor or Outdoor)
Reference Drawings:
Vertical Wall Mount............................................................................................ DWG-130545
Use this method when the overall display has modules mounted on top of one another.
1� Before attaching the digit module to the wall, attach the caption module to the digit
module as described in Installing Caption Modules (p�4).
Note: Extra strut length is not required when caption modules are mounted at either
the top or bottom of the column.
2� Attach vertical mounting struts to the wall. Strut length will vary depending on the
total number of display modules. Center-to-center distance between vertical struts is
8'-10.5" (2705 mm) for 9' (2743 mm) wide modules.
3� Use 3/8" bolts to attach the modules to spring nuts in the struts (Figure 4). Mount the
lowest module rst, and then add modules working upward.
Figure 4: Spring Nut in Strut

Mechanical Installation
6
Horizontal Wall Mounting (Indoor Only)
Reference Drawings:
Strut Spacing, Horizontal Wall Mounting.......................................................... DWG-129905
End Bracket Attachment, Horizontal Wall Mounting...................................... DWG-129906
Horizontal Wall Mounting, Final Steps............................................................... DWG-129907
Use this method when the overall display has modules mounted side by side.
1� Before attaching the digit module to the wall, attach the caption module to the digit
module as described in Installing Caption Modules (p�4).
Note: Extra strut length is not required when caption modules are mounted at either
the top or bottom of the column.
2� Attach mounting struts to the wall. Strut length will vary depending on the total
number of display modules. Refer to DWG-129905 to determine strut length and the
center-to-center distance between the struts.
3� Attach the end brackets to the right end of all the modules in the left column. Next,
attach brackets to the left end of all the modules in the right column. Refer to DWG-
129906.
4� Use 3/8" bolts to attach the modules in the left column to spring nuts in the struts
(Figure 4). Mount the lowest module rst, and then add modules working upward.
5� Starting with the bottom-right module, insert the screw heads on the end brackets of
the left side of the cabinet into the keyholes on the mating bracket of the right side of
the left column cabinet, and press down on the right side until both cabinets are ush
and level horizontally. Refer to DWG-129907.
6� Once the right column cabinet is joined to the left column cabinet, use 3/8" bolts to
attach the right end of the right column module to spring nuts in the struts (Figure 4).
7� Repeat Steps 5–6 for all remaining right column modules, working upward.
Corner-Mounting (Indoor Only)
Reference Drawings:
Corner Mount...................................................................................................... DWG-130508
If the display is to be mounted across the corner of adjoining walls, corner-mounting
brackets may be ordered as an option. DWG-130508 details this type of mounting.
Multi-line display models that use a single vertical arrangement of modules may be
mounted with corner brackets. However, horizontal display congurations cannot be
mounted across a corner using the simple brackets. Such displays must be attached
to a structure or framework that spans across the corner and safely supports the entire
display. This type of mounting must be designed by a qualied engineer.