dams TGSMARM User manual

E
1
2
C
E
E
7
4
9
-90 -15
36 3-12Kg
7
8
89
7
234
12
345
12
F
D
A B
/11
M6x12MM
!
1 2
11
10
7
8
9
10
11
Installation guide A(4PCS) B(4PCS) C(3PCS) D(8PCS) E(1PC) F(1PC)
4x4mm
Allen Key 5x5mm
Allen Key
Perforated plate
Long screw
Hand wheel
Pressure plate
Base mounting plate
Clip
Protection pad 1
Protection pad 2
Protection pad 3
Monitor Arm
VESA plate
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
1 pc
STEP 1
The Preparation Before Monitor Installation
1.Make sure there are VESA holes 100x100mm or 75x75mm in the monitor. If not, the mount cannot be installed.
2.Remove the original fixed base of monitor.Be careful not to scratch the screen.
75x75mm,100x100mm
75x75mm,100x100mm
STEP 2-A
Option1:
For desk thickness:
20-30mm
Tighten
DESK
DESK
Caution
STEP 2-B
Option2: Grommet
Notice: Keep the counterbore
side down
Available hole size:8.5-70mm
DESK
For desk thickness:25-100mm
Tighten
Connect the plate and monitor
monitor
Use washer if needed (D)
Use the allen key (F) to tighten the screw
STEP 3
Tighten
STEP 4
Install the monitor to the arm
Hang the monitor on the plate
from top to bottom and ensure
it is tightened
Tighten
VESA plate
Item No.: TGSMARM
C
5
10
E
1

3
F
F
6
Max:510
259
75
100
75
100
179
±180°
±135°
±90°
Max:30
Max:622
360°
-90°
15°
76
F1
2
STEP 5
Factory setting: 5-7KG
To adjust the swivel function by 5*5 allen key(F) on position 1
To adjust the tilt function by 5*5 allen key(F) on position 2
Cable management
take off cable
management Cable
ut cable a a e e t
back to cover the cables
Specification
Adjust the monitor
Please do not fully reverse the
monitor screen-to prevent
damage to the fixings.
Caution
To equalise the mount and
monitor's weight-please
CAUTION
This product contains small items that could be a choking hazard if swallowed. Keep these items away from young children.
● Make Sure these instructions are read and completely understood before attempting installation. If you are unsure of any part of this installation, please contact a professional
installer for assistance.
● The desk or mounting surface must be capable of supporting the combined weight of the mount and the display,otherwise the structure must be reinforced.
● Safety gear and proper tools must be used. A minimum of two people are required for this installation. Failure to use safety gear can result in property damage, serious inju ry or
death.
● please check joint parts every two months, making sure the screws are nor loosened.
This product was designed to be installed on a desk. Before installing, make sure the mount will support the combined load of theequipment and
hardware. Never exceed the maximum load capacity 12 KG, or else it may result in product failure or personal injury.
Note:this product is intended for indoor use only. Use of this product outdoors could lead to product failure or personal injury.
Warning:
obsolete products can be sent back to the manufacturer or handed over to professional institutions.
To maintain the gas mechanism in peak performance - it is suggested to raise the monitor arm up to the maximum height: ideally twice per month.
This product contains high pressure gas spring parts, please do not put it into fire, high temperature, or disassemble it, which will lead to
personal injury. The