DANAGE DOMINO User manual

DANAGE DOMINO Target stand A/2014.
Assembly instructions.
DANAGE of Scandinavia ApS • Industrivej 13 • 6310 Broager • E-mail: [email protected] / [e-mail]
Tlf.: [phone] • CVR: 14362975 • Webpage: www.domino-target.com • © copyright all rights reserved

DANAGE DOMINO Target stand A/2014 •Assembly instructions
DANAGE of Scandinavia ApS • Industrivej 13 • 6310 Broager • E-mail: [email protected] / [e-mail]
Tlf.: [phone] • CVR: 14362975 • Hjemmeside: www.domino-target.com • © copyright all rights reserved
Part A and B, the legs for
the target stand.
Part C, cross batten, front.
Part D and E (identical), cross battens,
backside top and bottom.
Part A and B are placed parallel,
appr. 132 cm apart (1 bushing facing
upwards and 3 bushings outwards).
Mount cross batten C with the 2
longest screws.
1
2
Part G, 2
target matt
holders.
2 screws 6x70 mm, 1
allen key, 6 screws 6x50
mm, 2 wing screws
6x40 mm and 2 eyebolts
6x70 mm with washers.
Part F, 2 side
battens.
D
E
The cut-out in C is
smaller than in D
and E.
C
A/B
C
3 bushings
facing outwards.
1 bushing
facing upwards.

DANAGE DOMINO Target stand A/2014 •Assembly instructions
DANAGE of Scandinavia ApS • Industrivej 13 • 6310 Broager • E-mail: [email protected] / [e-mail]
Tlf.: [phone] • CVR: 14362975 • Hjemmeside: www.domino-target.com • © copyright all rights reserved
3
The target stand is turned back
side up, and cross batten D and
E is fastened as shown in the
image. One can choose between
2 positions for cross batten D.
4
The target stand is
raised to a slightly
unfolded standing
position, as shown.
Side batten F is
fastened with a screw.
5
5. The wing screw is fastened in one of the 3
holes and the side batten is turned down and
fastened to the back leg. The 3 holes gives the
target stand different angles. The innermost
hole (appr. 3oangle) is great for short distance
shooting, the middle hole (appr. 8oangle) is
great for medium distances, such as 30-50 m,
while the last hole (appr. 13oangle) is great for
distances beyond 50 m.
For transport/storage, when the target stand is
folded, the side batten is fastened to the front
leg only, using the wing screw in the middle
hole.
D
E
F

DANAGE DOMINO Target stand A/2014 •Assembly instructions
DANAGE of Scandinavia ApS • Industrivej 13 • 6310 Broager • E-mail: [email protected] / [e-mail]
Tlf.: [phone] • CVR: 14362975 • Hjemmeside: www.domino-target.com • © copyright all rights reserved
6. Target matt size A
(132x132 cm) is mounted
by “leaning” the lower
part of the frame onto the
cross batten and then
tilted into position.
NOTE: If adjustable
frame: The adjustable
corners positioned
upwards! (Adjustable
frame is available on
request).
6
The target matt is
put up in the stand
like shown.
7
7. Position Target matt
holder Part G closest
possible to frame and
fasten it by eyebolt with
washer.
Note: 4 (2x2) positions
available.
Part G