Leviton EPED1 User manual

PK-A3430-10-00-5A
Single and Dual Mount
Back-to-Back Pedestal
Installation Manual
Cat. Nos. EPED1, EPED2
For use with Cat. Nos. EV320, EV32W, EV48W, and EV48S
WEB VERSION

WEB VERSION

TABLE OF CONTENTS
1 Warnings ........................................................................................................................................4
2 Installation ......................................................................................................................................5
2.1 Making Drill Holes.............................................................................................................5
2.2 Thread in Cable.................................................................................................................6
2.3 Anchoring ..........................................................................................................................6
2.4 Bracket Installation ..........................................................................................................7
2.5 Connector Base and Hook Installation ...........................................................................8
2.6 Mounting and Connecting the Charging Station ...........................................................9
3 FCC and Warranty .......................................................................................................................10
WEB VERSION

1 WARNINGS
4
Failure to follow the safety instructions can result in risk of death, injuries and damage to the device!
The producer assumes no liability for claims resulting from this!
Electrical hazard!
This installation manual is intended for qualified personnel only. The information and instructions in the
manual about selecting the location, installation and connection of the charging station must be adhered to.
Safety Instructions
Use of this manual
• The installation, commissioning and maintenance of the charging station may only be performed by
correctly trained, qualified and authorized electricians who are fully responsible for the compliance with
existing standards and installation regulations. Observe the instructions given for selecting the location
and the constructional requirements!
• If the specifications for the location are not observed, this can result in death, serious physical injury or
equipment damage if the corresponding precautionary measures are not met!
• The back-to-back pedestal must always be fitted with two charging stations!
WEB VERSION

2 INSTALLATION
2.1 Making Drill Holes
1. Mark 4 holes on the concrete foundation using the base-plate of the pedestal. Make sure that the
connection cable is located precisely underneath the opening in the base-plate.
2. Drill 4 mounting holes:
Diameter: 0.39 in. (10 mm.)
Drill-hole minimum depth: 3.31 in. (84 mm.)
3. Hammer the anchors (not included) so that they are flush with the floor.
5
8.62 in. (219.0 mm.)
3.67 in. (93.2 mm.)
0.39 in. (10.0mm)
54.92 in. (1395.0 mm.)
7.87 in. (200.0mm) 3.15 in. (80.0mm)
10.63 in.(270.0 mm.) 6.10 in. (155.0 mm.)
WEB VERSION

2 INSTALLATION
2.2 Thread in Cable
1. Thread the connection cables from the bottom through the pedestal upwards through the
cable opening.
2.3 Anchoring
1. Position the pedestal directly over the cable outlet.
2. Anchor the pedestal to the foundation using four (4) sets
of of M8 nut / M8 flat washer / M8 spring washer.
3. Cap the base cover down carefully.
6
Base Cover
WEB VERSION

2 INSTALLATION
2.4 Bracket Installation
1. Insert the cable gland into the pedestal.
2. Install the mounting plate to the pedestal with screws provided.
7
WEB VERSION

2 INSTALLATION
2.5 Connector Base and Hook Installation
1. Use 4 of M5x22 mm. screws to fix the connector base and hook
in the corresponding position.
8
WEB VERSION

2 INSTALLATION
2.6 Mounting and Connecting the Charging Station
1. Mount the charging stations on the pedestal using 2 of M5X12 mm. screws on both sides
of the charger.
2. Release the 4 of M5X12 mm. screws of the wiring window at the back
3. Thread the connection cables from the bottom through the pedestal upwards through
the cable opening.
4. Perform the electrical connection and commissioning in accordance with the instructions.
5. Fix the four 4 of M5X12 mm. screws to finish the installation.
9
WEB VERSION

FCC STATEMENT:
This device complies with Part 15 of the FCC Rules and ISED License-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept
any interference received, including interference that may cause undesired operation. Changes or modifications not
expressly approved by Leviton could void the user’s authority to operate the equipment.
These limits are designed to provide reasonable protection against harmful interference in a commercial installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This Class A digital apparatus complies with Canadian CAN ICES-3(A)/NMB-3(A)
FCC SUPPLIER’S DECLARATION OF CONFORMITY:
This device manufactured by Leviton Manufacturing Co., Inc. 201 North Service Road, Melville, NY 11747.
www.leviton.com. This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
TRADEMARK DISCLAIMER:
Leviton and the Leviton logo are trademarks of Leviton Manufacturing Co., Inc. Use herein of third party trademarks,
service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the
trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
Leviton Manufacturing Co., Inc.
201 North Service Road, Melville, NY 11747
Visit Leviton’s website at www.leviton.com
© 2022 Leviton Manufacturing Co., Inc. All rights reserved.
Specifications and price subject to change at any time without notice.
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale
by Leviton is free of defects in materials and workmanship under normal and proper use for 2 years from the purchase date.
Leviton’s only obligation is to correct such defects by repair or replacement, at its option. For details visit www.leviton.com or call
1-800-824-3005. This warranty excludes and there is disclaimed liability for labor for removal of this product or reinstallation. This
warranty is void if this product is installed improperly or in an improper environment, overloaded, misused, opened, abused, or altered
in any manner, or is not used under normal operating conditions or not in accordance with any labels or instructions. There are no other
or implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any implied warranty is
required by the applicable jurisdiction, the duration of any such implied warranty, including merchantability and fitness for a particular
purpose, is limited to 5 years. Leviton is not liable for incidental, indirect, special, or consequential damages, including without
limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this warranty
obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton Manufacturing of
Canada ULC to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-Claire (Quebec), Canada H9R 1E9
or by telephone at 1 800 405-5320.
For Technical Assistance Call: 1-800-824-3005 (USA Only) or 1-800-405-5320 (Canada Only) www.leviton.com
10
3 FCC AND WARRANTY
WEB VERSION

WEB VERSION