Danfoss TP7000 Series User manual

TP7000 Range
Electronic 7 Day Programmable
Room Thermostat
Installation Guide
Danfoss Heating
MAKING MODERN LIVING POSSIBLE
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

TP7000 RANGE
2
For a large print version of these instructions
please call Marketing on 0845 121 7400.
Danfoss can accept no responsibility for possible errors in catalogues, brochures, and other
printed material. All trademarks in this material are property of the respective companies.
Danfoss and the Danfoss logotype are trademarks of Danfoss A/S. All rights reserved.
®
Certification Mark
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

Danfoss Heating 3
F
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
GB
Installation Instructions
TP7000 Range
Electronic Programmable Room Thermostat
Index
1.0 Installation Guide .....................................................................................4
2.0 System Overview.......................................................................................4
3.0 Installation ...................................................................................................5
3.1 DIL Switch Settings ...........................................................................5
3.2 Setting Optimum Start Control....................................................6
3.3 TP7000 Wiring (Not RF models)....................................................6
3.4 Receiver Wiring (RF models) ..........................................................7
3.5 Commissioning (RF versions only)...............................................7
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

TP7000 RANGE
4
F
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
GB
Thermostat Features TP7000-RF TP7000
TP7000A
TP7000-M
TP7000-MA TP7000-M 24
Power supply 2 x AA/MN1500/LR6
alkaline batteries 230v, 50 Hz 24v, 50 Hz
Memory backup
Capacitor during
battery change for 1
minute
Rechargable cell, 24 hrs (*1)
Switching action of output
relay N/A 1 x SPDT, Type 1B
Switch rating of relay contact,
voltage and current N/A 3(1) A, 10-230 volts
Transmitter frequency
(RF only) 433.92 MHz N/A
Transmitter range
(RF only) 30m max. N/A
Rated Impulse Voltage N/A 2.5Kv
Dimensions (mm) 138 wide x 88 high x 28 deep
Ball Pressure Test 75°C
Temperature Range 5-30°C
Design Standard EN 60730-2-7 (EN300220 for RF)
Control Pollution Situation Degree 2
Time accuracy ± 1 min.
Temperature accuracy ±1°C
*1: Unit must powered up for 6 days to charge cell before full back-up is available
Important note RF products: Ensure that there are no large metal
objects, such as boiler cases or other large appliances, in line of
sight between the transmitter and receiver as these will prevent
communication between thermostat and receiver.
1.0 Installation Guide
2.0 System Overview
Please Note:
This product should only be installed by a qualified electrician or
competent heating installer and should be in accordance with the
current edition of the IEEE wiring regulations.
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

Danfoss Heating 5
F
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
GB
All models
w
15/2 day programming 7 day programming
w
2Optimum start contoller enabled Optimum start contoller disabled
w
3Chrono-proportional control On/O control
TP7000, M, & RF models with 3/6 cycles per hour option
w
4Chrono-proportional, 6 cycles / hour Chrono-proportional, 3 cycles / hour
3.1 DIL Switch Settings
 First remove the wallplate from the back of the unit.
 From the top left hand corner of the wallplate, there must be
clearances of at least 15mm to the right, 15mm to the left, 30mm
above and 100mm below in order to mount the plug-in module.
 Before mounting the unit ensure the 4 DIL switches on the
rear of the unit have been moved to the required settings (see
below). Factory preset is 7-day, with Optimum Start and Chrono-
proportional control OFF.
NOTE
Use Chrono 3 for high thermal inertia systems, e.g. floor standing cast iron
boilers.
Use Chrono 6 for low thermal inertia systems, e.g. low water content
boilers and combi boilers.
3.0 Installation
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

TP7000 RANGE
6
F
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
GB
3.3 TP7000 Wiring (not RF models)
7-day - each day can be programmed with different times and
temperatures.
5/2 day - one set of times & temperatures for weekdays, and another
set for weekends.
Optimum start control - function which switches the heating on
earlier than the Event 1 programmed time to ensure the required
temperature is achieved by the set time.
Chrono-proportional control - energy saving feature which fires the
boiler at regular intervals to maintain a set temperature, achieving a
constant ambient environment for the user.
3.2 Setting Optimum Start Control
-4°C
-3°C
-2°C
-1°C
A
B
C
120
min.
90
min.
60
min.
30
min.
Event 1
time (0
)
D
 Set Sw2 to OSC ON
(see DIL settings page 4)
 Select OPTIMISER CURVE in
programming mode
A Event 1 Set Point
BDeviation from Set Point
CSwitch On Time prior to Event
DOptimiser Curve Setting
1234567
ELECTRONICS
REMOTE
SENSOR
'A' models
only
COM ON OFF
BC
M 24V models only
24V
LN
M 230V models only
230V
Note: 1.0mm2solid copper cable should be used to connect the
remote sensor to the TP7000A. Please ensure that:
a) the cable length does not exceed 50 metres,
b) to avoid electrical interference the cable should not be run
parallel in close proximity to other cables carrying mains electricity,
and where necessary the cable should cross over mains cabling at
right angles.
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

Danfoss Heating 7
F
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
GB
1. TP7000-RF
Press the recessed RESET button, using a non-
metallic object, to reset the unit.
2. Press & hold the recessed LEARN button for 3
seconds, using a non-metallic object.
NOTE: Thermostat now transmits continuously for 5 mins.
3. RX1 - Press and hold buttons PROG and CH1
for 3 seconds until green light flashes once.
4. RX2 (if applicable)
Stat 1 - perform steps 1-3.
Stat 2 - wait 5 mins, perform steps1-2 and then press PROG and CH2
on RX2.
RX3 (if applicable)
Stat 1 - perform steps 1 – 3.
Stat 2 - wait 5 mins, perform steps 1-2 and then press PROG and CH2
on RX3.
Stat 3 - wait 5 mins, perform steps 1-2 and then press PROG and CH3
on RX3.
5. TP7000-RF - Press or  to return the unit
to normal operation.
3.5 Commissioning (RF versions only)
If the thermostat and the receiver have been supplied together
in a combined pack, the units have been paired in the factory
and no commissioning is required (RX1 only).
To tune the RX receiver to the frequency of the thermostat signal, follow
steps 1-5 below.
RX1
LEARN
RESET
3.4 Receiver Wiring (RF models only)
1234
ELECTRONICS
NL
COM ZONE
1 ON
ZONE
1 OFF
A
ELECTRONICS
BC123456
NLZONE
1 ON
ZONE
1 OFF
ZONE
2 ON
ZONE
3 ON
COM
TERMINAL 6
RX3 ONLY
RX1 RX2 & RX3
Note: 1) For mains voltage operated systems link terminal 2 to mains live supply.
2) Power supply to unit must not be switched by timeswitch.
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

TP7000 RANGE
8
GB
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
F
Instructions d’installation
Série TP7000
Thermostats d’ambiance programmable
Index
1.0 Instructions d’installation.....................................................................9
2.0 Specifications..............................................................................................9
3.0 Installation ................................................................................................ 10
3.1 Réglages d’installateur.................................................................. 10
3.2 Démarrage anticipé (OSC)........................................................... 11
3.3 TP7000 Câblage (versions câblées seulement).................... 11
3.4 Câblage du Récepteur RX (modèles RF uniquement)....... 12
3.5 Instructions (versions câblées)................................................... 12
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

Danfoss Heating 9
GB
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
F
1.0 Instructions d’installation
Importante: Veiller à ce qu’aucun gros objet métallique (caisson de
chaudière ou autres gros appareils domestiques) ne fasse obstacle aux
communications entre le thermostat et le récepteur.
2.0 Specifications
Caractéristiques TP7000-RF TP7000
TP7000A
TP7000M
TP7000MA TP7000M 24
Alimentation 2 piles alcalines AA/
MN 1500/LR6 230v, 50 Hz 24v, 50 Hz
Mémoire non volatile
Suffisante pour
remplacer les piles
endéans la minute
Rechargeable
(voir note 1*)
Type de contact N/A 1 x SPDT, Type 1B
Charge de contact,
voltage et courant N/A 3(1) A, 10-230V
Fréquence d’émission
(modèles RF) 433.92 MHz N/A
Rayon d’action
(modèle RF uniquement)
Max. 30
métres N/A
Tension assignée de
tenue au choc N/A 2.5Kv
Dimensions (mm) 138 largeur x 88 hauteur x 28 profondeur
Essai à la bille 75°C
Plage de températures 5-30°C
Normes de fabrication EN 60730-2-7 (EN300220 pour RF)
Pollution Degré 2
Précision de l’horloge ± 1 min.
Précision de la
température ±1°C
Note 1) : Le thermostat doit être alimenté pendant 6 jours pour disposer de la
mémoire non volatile.
Remarque:
Ce produit doit être installé exclusivement par un électricien
qualifié ou un installateur de chauffage compétent et doit être
conforme à la version en vigueur des réglementations de câblage
IEEE.
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]

TP7000 RANGE
10
GB
D
ES
DK
NL
I
GR
PL
LT
CZ
HR
RO
F
3.0 Installation
 Retirez tout d’abord la plaque murale de l’arrière de l’appareil.
 Par rapport au coin gauche supérieur de la plaque murale, vous
devez disposer d’espacements d’au moins 15 mm à droite, 15
mm à gauche, 30 mm au-dessus et 100 mm en-dessous afin de
pouvoir monter le module enfichable.
 Avant de monter l’appareil, assurez-vous que les 4 microcontacts
situés à l’arrière de l’appareil soient placés dans les positions
requises (voir ci-dessous). Le pré-réglage d’usine est 7 jours,
avec la régulation Optimum Start (démarrage optimum) et sans
démarrage anticipé (OSC OFF) et en mode Tout ou Rien.
3.1 Réglages d’installateur
REMARQUE
Utilisez Chrono 3 pour les systèmes à inertie thermique élevée, ex.
chaudières en fonte au sol.
Utilisez Chrono 6 pour les systèmes à faible inertie thermique, ex.
chaudières à faible contenu d’eau et chaudières mixtes.
Tous les modèles
Sw 1Programmation 5/2 jours Programmation 7 jours
Sw 2Optimum Start Contol on Optimum Start Contol off
Sw 3Règulation Chrono-proportionnelle Règulation On/Off
TP7000, M, & RF modèles avec 3 ou 6 cycles par heure
Sw 4Chrono-proportionnelle, 6 cycles par heure Chrono-proportionnelle, 3 cycles par heure
www.boilersp.ru Москва, ул. Народного Ополчения, д. 34, стр. 3 [phone]