Danz RHINE User manual

Instruction Manual
RHINE SPA

The first thing to do with your Rhine Spa is to set the time.
In order to do this, hold down the Mbutton for 5 seconds until rtC flashes on the screen
Use the button to change the minutes
Use the button to change the hours
Once you’ve selected the correct time wait for 4 seconds and it will go back to the main screen.
Press and hold Mfor 5 seconds until rtC flashes on the screen. Press again for FSt - this is Filtration Start
Time. During filtration the system is cleansing itself, purifying the pipeline equipment and heating the water.
This should ideally bet set to a time when you are asleep and therefore not going to be using the tub. We
recommend about 4am.
Use the button to cycle between times
Once you have set a time press Magain until FTl appears. This is the duration of the filtration cycle. We
recommend 2 hours. Use the arrows to select a time.
If you press Magain and see Adj, please ignore this. This is to fine tune the temperature sensors in the spa
and is only to be used by a Danz Spas technician.

Now, let’s look at the different modes on the control panel.
Pressing M will cycle the spa through different modes manually. The different modes are:
NOM –normal operation
NOM ECE –normal mode for 1 hour, then economy mode automatically
ECE –economy mode
FIL –filtration mode
What do these modes mean?
NOM –The system is in normal operation, the heater is on (if the desired temperature isn’t reached)
ECE –the system will only heat the water during the pre-determined filtration cycle
FIL –the system is in filtration mode. The heater will not be in operation. Manually using the filtration
mode is only needed if the system has been switched off for long periods of time.
If you are going to be using the spa on a regular basis, every day or every two or three days, set the spa to
NOM so that the spa will always be hot for you. You can then use the arrows to adjust the minimum
temperature that you want the spa to remain at.
When the water temperature falls below 6.7oC the spa will switch to anti-freezing mode. All the pumps and
blowers will operate for 30 seconds and then turn off. All the heaters and circulation pumps will switch on. The
panel will show ICE.
Pressing this symbol switches on the LED lights. They will cycle through various
colours. Press the button again to stay on a specific colour, and again to switch the
lights off. The lights will automatically shut off after 2 hours.
Pressing this symbol switches on the air blower. The blower will automatically turn
off after 25 minutes.
Pressing this symbol switches on the jets and fountains.

Important Safety Instructions
Your physiological response to hot water is very subjective and depends on your age, health, and medical history. If you
don’t know your tolerance to hot water, or experience, dizziness, headaches or nausea you should exit the spa immediately
and cool down.
WARNING
1. Children should NOT use a spa without adult supervision.
2. Do not allow children to submerge their head under water.
3. Do not use a spa unless all suction guards are installed to prevent body and hair entrapment. Do not sit in front of, or on top
of the suction fittings or skimmer, as this will obstruct proper circulation and may result in personal injury.
4. Never operate the spa pump at high speed without having all suction and return lines open.
5. Always keep the hardcover installed and locked when the spa is not in use.
6. People using medications and/or having any adverse medical history should consult a physician before using a spa.
7. People with infectious diseases should not use a spa.
8. Use caution when entering or exiting a spa. Where practical, install a safety grab bar or handrail. Turn off the jets before
entering the spa to improve visibility of the steps or flat entry area.
9. Do not use drugs or alcohol before or during the use of a spa.
10. Pregnant women should consult a physician before using a spa.
11. As prolonged immersion in water temperatures in excess of 38°C (100°F) may be damage your health, we recommend
measuring
the water temperature with an accurate thermometer before entering the spa. We also recommend establishing lower
temperatures and shorter periods of use for young children and/ or those users potentially affected by hot temperatures.
12. Do not use a spa immediately following strenuous exercise.
13. Do not permit or use electric appliances (such as light, telephone, radio or television) within 1.5 m (5 ft) of a spa, unless such
appliances are rated at 12VDC or less.
14. Test the RCD (Ground Fault Circuit Interrupter) monthly.
15. Post emergency phone numbers for Police, Fire Dept., and Ambulance at the nearest phone.
HYPERTHERMIA
Since your spa can be set to reach temperatures of 40°C (104°F), users should be aware that extended submersion in water
that exceeds normal body temperature can lead to hyperthermia.
The causes, symptoms and effects of hyperthermia are be described as follows:
Hyperthermia occurs when the internal temperature of the body reaches several degrees above the normal body
temperature of 37°C
(98.6°F). The symptoms of hyperthermia include drowsiness, lethargy, and an increase in the internal temperature of the
body. The effects of hyperthermia include:
•Unawareness of impending hazard
•Failure to perceive heat
•Failure to recognize the need to exit the spa
•Physical inability to exit the spa
•Foatal damage in pregnant woman
•Unconsciousness resulting in the danger of drowning
WARNING
THE USE OF ALCOHOL, DRUGS OR MEDICATION CAN SIGNIFICANTLY INCREASE THE RISK OF HYPERTHERMIA.
Choosing the Right Location
In this part, we describe outdoor spa installations. The following information will assist you in choosing the right location for
your individual needs. When making your decision, always remember that spas can be enjoyed yearround, indoors or out,
regardless of the climate. Many spa owners report that their favourite seasons are the cooler autumn and winter months,
whilst others praise the enjoyment of using their spa in the warmer spring and summer months.
Outdoor Locations
For a variety of reasons, outdoor locations are a far more popular choice. Some of the reasons include:
•Limited indoor space
•Delivery complications due to door openings, stairwells, etc.
•Limited budget (indoor installations usually also involve interior home renovations)
•Desire for an outdoor entertainment centre
•The spa is being installed adjacent to an existing or planned swimming pool
•Concerns over splashing water inside the home
For those who choose an outdoor location, spa operating temperatures can be adjusted to match the season. In colder
months, many owners will operate their spa in the range of 38-40°C (101 -104°F). During warmer months, an operating

temperature of 36-37°C (97-99°F) will provide a refreshing retreat. If you should choose an outdoor location, you will find
further information as outlined in the section below.
Special Considerations
Contact your local building department to determine if a building permit is necessary and for information on applicable
bylaws (distance from property lines, buildings, fencing requirements, etc.).
•If you are doing any excavating, contact your local gas, hydro, and cable-company to ensure that there are no underground
lines
•Locate the spa, where practical, within close distance of a door to the house. This will maximize potential winter use.
•Ensure that your pump(s), controls, drain-valve and thermal probe are easily accessible and protected.
•If possible, locate the spa where you will enjoy some privacy. If this is not possible, a partial privacy or wind partition, or
proper placement of the optional cover lifter should provide adequate privacy. Spa equipment is generally designed for
indoor (out of the direct elements) use. When your Spa is equipped with a factory-installed cabinet, and installed as per the
guidelines of this manual, the equipment is adequately protected. If the spa is shipped without a cabinet, your custom
cabinet or other structure must be designed to supply protection for the spa equipment from rain, snow, splash water, etc.,
but still designed in a manner to ensure adequate ventilation.
Important Usage Warnings - Non Warranty Faults
Should we ever need to visit you to repair your spa, it is likely that you would be charged the full cost of a repair if we found
that the cause was the result poor maintenance or customer negligence. Paying full attention to the issues below will help to
reduce the risk of damage to your spa. Please also read your warranty document in full. This can be found at the end of this
document.
Water Treatment
One of the most crucial aspects of spa maintenance is water treatment. Poorly treated spas may result in high levels of pH
or Water Hardness. Either of these problems may result in lime scale build-up which can damage your spa surface, pumps,
jets or heaters. If we find a build-up of lime scale on your spa, this would not be covered under warranty.
Different chemical packs have different methods of caring for the water. You will need to refer to the guide that came which
your chosen chemical pack for exact details on how to treat your water. You can also download a general water treatment
guide from our website.
Filling Up Your Spa - Air Locks
The correct way to fill up your spa is to place your hosepipe inside the filter compartment. Some customer place their
hosepipe inside the spas main seating area however, doing this may cause a build-up of air inside the heater (known as an
air lock). Over time, air locks will cause the heater to fail. This would not be covered under warranty. To avoid this problem
ensure you fill up the spa through the filter window. You can tell if you have an air lock by turning on the circulation pump. If
no water appears to circulate through the system it is very possible that you have an air lock. To resolve this problem, loosen
the unions at the side of the suction end of the circulation pump until water begins to flow through.
Filters
Poor filter conditions are one of the biggest causes of faults that are not covered under warranty. Poor filter conditions allow
particles to roam in the spas water. These tiny particles can cause damage to the spas components. One of the first things
our engineer will check when visiting your spa is the condition of your filter. If we find your filter is in poor condition, your
repair will not be covered under warranty.
There are a number of ways of caring for your filter. Crucially, we recommend that you regularly soak your spa in filter
cleaner every few weeks. Additionally, we recommend changing your filter every 6-9 months (depending on usage). Some
customers purchase a spare filer at the time of ordering and alternate between the two.
Use of Cover
Your spa cover must be used when the spa is not in use. Leaving the cover expose allows leaves, dust etc to enter your spa.
These may then be sucked in the spas pipework causing blockages or damaging the equipment. If our engineer finds leaves
for example inside your spa, your repair would not be covered under warranty.
Caring for Wooden Skirting
Wood skirting has a tendency to fade and lose its like-new appearance with time. You should re-stain your spa’s skirting
once every six months. Lightly sand the surfaces to remove any dirt and smoothen rough surfaces. Re-stain wood surfaces
using a suitable stain. Do not use varnishes, shellacs or surface sealants. Warranty on spa skirting is only valid if spas have
been regularly stained.
Frost Damage
As water freezes in the winter, it expands. This expansion can cause damage to your spas components and pipework. If you
intend to use the spa throughout winter then you must have the frost prevention system turned on. If you do not intend to
use the spa throughout winter than the spa must be ‘winterized’. Please see our website, or contact us for more information
on winterizing your spa. Problems arising from frost damage are not covered under warranty.