M-Spa Blue Sea B110 User manual

2
SAFETY INSTRUCTIONS
WARNING
When installing and using this electrical equipment, basic safety precaution should always be followed,
including the following:
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS.
WARNING: RISK OF ELECTRIC SHOCK. Insert the plug only to a properly grounded socket.
WARNING: The spa must be supplied by an isolating transformer or supplied through a ground-fault circuit
interrupter (GFCI) having a rated residual operating current not exceeding 30mA.
WARNING: GFCI must be tested before each use.
WARNING: If the supply cord is damaged, it must be replaced immediately by the manufacturer, its service
agent or similarly qualified person in order to avoid a hazard.
WARNING: To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply;
provide a properly located receptacle.
WARNING: No part of the appliance is to be located above the bath during use.
WARNING: Parts containing live parts, except parts supplied with safety extra-low voltage not exceeding
12V, must be inaccessible to a person in spa pool; Earthed appliance must be connected to the fixed
receptacle which is permanently connected to fixed wiring. Parts incorporating electrical components,
except remote control devices, must be located or fixed so that they cannot fall into the spa pool.
WARNING: The plug of spa shall be more than 3.5m away from the pool.
WARNING: Spray head must not be used.
WARNING: The outlet of Spa must not be connected to any tap or fitting other than those specified.
WARNING: Electric installations should fulfill the requirements of local standards.
WARNING: TO AVOID THE ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS RAINING.
WARNING: To reduce the risk of injury, do not permit children to use this product unless they are closely
supervised at all times.
WARNING: Water attracts children. Always have the Spa locked with its cover after each use.
WARNING: Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other
equipment.
WARNING: Do not overexert press down or uplift the control panel device. Do not put any heavy on control
panel device after installation.
WARNING: Pets should be kept away from spa to avoid damage.
WARNING: When the bubble function is going to be in function, make sure the cover of Spa must be opened
first.
WARNING: Do not switch on if there is any possibility that the water in the spa is frozen.
WARNING: Use only approved accessories. Use of non-approved accessories could void the warranty.
DANGER: Risk of accidental drowning. Extreme caution must be exercised to prevent unauthorized access
by children. To avoid accidents, ensure that children can not use this spa unless they are supervised at all
times.
WARNING: RISK OF ELECTRIC SHOCK. Install at least 1.5m from all metal surfaces.
WARNING: RISK OF ELECTRIC SHOCK. Never operate any electrical appliance when in your spa or when
your body is wet. Never place any electric appliance, such as a light, telephone, radio, or television, within
1.5m of spa.
WARNING: During pregnancy, soaking in hot water may cause damage to the fetus. Limit use to 10 minutes
at a time.

3
WARNING: TO REDUCE THE RISK OF INJURY:
A. The water in a spa should never exceed 40 °C (104 °F). Water temperature between 38 °C(100 °F) and
40 °C (104 °F) are considered safe for a healthy adult. Lower water temperature is recommended for
young children and when spa use exceeds 10 minutes.
B. Since excessive water temperatures has a high potential for causing fetal damage during the early
months of pregnancy, pregnant or possibly pregnant women should limit spa water temperatures to
38 °C(100 °F).
C. Before entering a spa, the user should measure the water temperature with an accurate thermometer
since the tolerance of water temperature regulating devices varies.
D. The use of alcohol, drugs, or medication before or during spa use may lead to unconsciousness with
the possibility of drowning.
E. Obese person and person with a history of heart disease, low or high blood pressure, circulatory
system problems, or diabetes should consult a physician before use a spa...
F. Person using medication should consult a physician before using a spa since some medication may
induce drowsiness while other medication may affect heart rate, blood pressure, and circulation.
WARNING: TO REDUCE THE RISK OF INJURY: Never pour water which higher than 40 °C (104 °F) into the spa
pool directly.
WARNING: The use of alcohol, drugs, or medication can greatly increase the risk of fatal hyperthermia.
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the
normal body temperature of 37 °C(98.6 °F). The symptoms of hyperthermia include an increase in the
internal temperature of the body, dizziness, lethargy, drowsiness, and fainting, The effects of hyperthermia
include failure to perceive heat; failure to recognize the need to exit spa; unawareness of impending
hazard; fetal damage in pregnant women; physical inability to exit the spa; and unconsciousness resulting
in the danger of drowning.
CONSULT YOUR PHYSICIAN FOR RECOMMENDATIONS.
CAUTION: The spa should not be setup or left out in temperature lower than 4°C
CAUTION: Do not use the spa alone.
CAUTION: People with infectious diseases should not use a spa.
CAUTION: Do not use the spa immediately following strenuous exercise.
CAUTION: Always enter and exit the spa slowly and cautiously. Wet surfaces are slippery.
CAUTION: To avoid damage to the pump, the spa must never be operated unless the spa is filled with
water.
CAUTION: Immediately leave spa if uncomfortable or sleepy.
CAUTION: Never add water to chemicals. Always add chemicals to water to avoid strong fumes or violent
reactions that may result in hazardous chemical spray.
CAUTION: Place only on surface that can withstand the floor loading requirement of your Spa.
NOTE: Please examine equipment before use. Notify after sales service center listed on this manual for
any damaged or missing parts at the time of purchase. Verify that the equipment components represent
the models that you had intended to purchase.

4
SPECIFICATIONS
INSTALLATON INSTRUCTIONS
NOTE: Ensure to check all parts are present.
A-1: PU cover with foil and zipper
A-2: top lid
B: control panel
C: Spa pool
D: test strip
E: digital lock
F: Inflation Hose
G: filter cartridge
H: outlet hose and inlet hose
I: repair kit
A-1.
A-2.
B. C
)
,
.
D. E.
G. H.
Bubble SPA
Style No.
B-110 Blue Sea B-130 Camaro B-140A/B Blue/brown (Elegance)
Item No. A081010 A0 81008
A081 027(blue)
A081 009(brown)
Seating capacity 4 4 4
Water capacity 1000L/265gallon 800L/211gallon 800L/211gallon
Outer Diameter 1.88m/74" 1.8m/71" 1.8m/71"
Inner Diameter 1.46m/58" 1.4m/55" 1.4m/55"
Height 0.70m/28" 0.8m/32" 0.70m/28"
Number of air jet 128 128 128
Power rated 110~120V, 60Hz 110~120V, 60Hz 110~120V, 60Hz
Heater 900W/1.22HP 900W/1.22HP 900W/1.22HP
Bubble 900W/1.22HP 900W/1.22HP 900W/1.22HP
Power cable length 4.5m/15 feet 4.5m/15 feet 4.5m/15 feet
Filter AC12V/65W 2300L/ 600gal/H AC12V/65W 2300L/ 600gal/H AC12V/65W 2300L/ 600gal/H
Top lid
polyester laminated PVC
with foil
PU leather with inflatable air
chamber
PU leather with foil
Cord-mounted GFCI GFCI GFCI

5
A. Site Requirements
WARNING: The floor has to be capable of supporting the expected load.
WARNING: An adequate drainage system has to be provided to deal with overflow water.
IMPORTANT: Because of the combined weight of the spa, water, and users, it is extremely important that
the base where the Spa is installed is smooth, flat, level and capable of uniformly supporting this weight
for the entire time the spa is installed. If the spa is placed on a surface, which does not meet these
requirements, any damage caused by improper support will void the warranty. It is the responsibility of the
Spa owner to assure the integrity of the site at all times.
a) Indoor Installation:
Be aware of special requirements if you install the spa indoor.
The floor must be able to withstand the capacity of the spa. The floor should be a non-slip, level
surface.
Proper drainage is essential for indoor spa installation. When building a new room for the spa, it is
recommended that a floor drain be installed.
Humidity is a naturally side effect with spa installation. Determine the effects of airborne moisture on
exposed wood, paper, etc. in the proposed location. To minimize these effects it is best to provide
plenty of ventilation to the selected area. An architect can help determine if more ventilation is needed.
NOTE: Do not install the spa on carpet or other material that can be damaged by moisture.
b) Outdoor Installation
WARNING: TO AVOID THE ELECTRIC SHOCK, DO NOT USE THE SPA WHEN IT IS RAINING.
No matter where you install the spa, it’s important you have a solid support foundation. If you are
installing the spa outdoors, ensure there are no sharp objects that could damage it and that the
location is level so the spa sits stably and properly.
During filling, emptying or when in use, water may spill out of the Spa. Therefore the spa should be
installed near a ground drain.
Do not leave the Spa’s surface exposed to direct sunlight for long periods of time.
B. GFCI Test
WARNING: RISK OF ELECTRIC SHOCK. The GFCI plug must be tested before each use.
WARNING: Insert the GFCI plug into a residual current device (GFCI) protected power receptacle only.
WARNING: Before inserting the plug into a power receptacle, make sure the current rate of the power
receptacle and the fixed wiring are suitable for the Spa. Contact a qualified electrician if you cannot verify.
1. Insert the plug into the power receptacle. (1)
2. Press the “RESET” button. The indicator light should turn red. (2)
3. Then press the “TEST” button. The indicator light should disappear. (3)
WARNING: Do not use if above test fails.

6
4 . Finally, press the “RESET” button again. The indicator light should turn red. The spa is ready for use.
(4)
C. Assembly
b) Screw the control panel onto the spa, fasten the ring to the pipe adaptor.
c) Connect the connectors. Make sure that the “ ” mark of each connector are properly matched
together.
d) Open the air valve under the control panel. Screw one end of inflation hose onto it.
e) Open the air valve on the Spa. Connect the other end of inflation hose into the valve.
(1) (2) (3) (4)
(b) (c) (d)
a) Unfold the Spa pool from the packaging.
Spread the Spa and cover. Make sure
both are right side up.
For B-130 and B-140 only
Put the side leather cover on the spa tub.
Attention: make sure the 2 holes on the leather
fit the right positions of spa tub.
(a)

7
f) As previously outlined, test spa’s GFCI plug.
g) Inflate the spa tub by pressing the “bubble” button
Attention: Do not over inflate.
Press the “bubble “ button to shut off the bubble function when the spa is properly inflated.
h) Remove the inflation and Screw the valve tight
i) Remove the inflation hose from the control panel and screw the valve tight
j) Screw the filter cartridge onto the water inlet on the spa wall by turning it clockwise.
k) Fill the Spa
Using a garden hose to fill the Spa at least to the water level printed on the Spa wall.
Warning: make sure the power pack is not plugged in before filling water into the SPA.
Note, for B-110 and B-140
(l) Place the Cover onto the Spa, fasten the zipper and lock the cover to the spa by using the digital lock in
the accessory pack
Note, for B-110 and B-140
How to change the combination of digital lock:
1) Original combination is set as 000
2) Push release button (a) in the direction of the arrow
shown and the lock will be released.
3) Set your desired combination by move the number wheel.
Please do not forget your new combination.
4) Insert back the steel cable to its end in the direction of the arrow.
The new combination is ready for use.
water line
(e) (f) (g)
(h) (j) (k)
(l)
(a)
(b)
(c)
(1) (2) (3)

8
LED Display: Once powered-up, the LED displays the current water temperature automatically.
Temperature Adjustment Buttons: Increase Decrease
Pressing the Temperature Increase or Temperature Decrease buttons will cause the LED to flash.
When it is flashing, you can enter the desired temperature setting. If you hold these buttons down
the values will rapidly increase or decrease. The new and desired temperature setting will remain
on the LED display for 5 seconds to confirm the new value.
NOTE: The set point temperature defaults to 40°C (104°F) when first plugged in.
NOTE: Temperature adjustment ranges from 20°C (68°F) to 40°C (104°F).
Water Filtration Button: This button turns the Filter Pump on and off.
The light of the water filtration button displays green when the filtration system is activated.
WARNING: Do not move the number wheels while the digital lock is open. Or you will change the
combination you just set. This will unable the digital lock.
WARNING: The cover is not a substitute for adult supervision; Children must be supervised at all times
around the Spa.
WARNING: Water attracts children; Always attach a spa cover and lock it after each use
Power pack operation
Power pack
CAUTION: You must ensure the power pack is prepared before operating, if you do not follow these
instructions the power may operate abnormally. Never dry-run the power pack as such type of operation will
void the warranty.
Note: The Water in the Spa must match the water line printed on the spa wall.
Note:
For B-130,
a) Unfold the top inflatable bladder.
b) Put the top leather cover on the top inflat-
able bladder.
c) Open the air valve under the control panel
device, then screw one end of air pipe on it.
d) Open the air valve on the top inflatable bladder,
and screw the other end of air pipe on it.
(b) (c)
Control panel
1. “BUBBLE” Button: Activates Bubbling system
2. “FILTER” Button: Activates Filter system
3. “HEATER” Button: Activates Heating and Filtering
system at the same time
4. “TEMPERATURE” Button: Set and show water tem-
perature
5. “ ” Button: Higher temperature
6. “ ” Button: Lower temperatrure

9
Cleaning the Filter CARTRIDGE
Please make sure to unplug the power pack from the electrical receptacle before the follwoing
actions.
1. Unscrew the filter cartridge by turning it coun-
terclockwise
2. Remove the filter cartridge cover.
3. The Filter Cartridge can be rinsed off with a gar-
den hose and reused. However, if the Filter Cartridge
remains soiled and discolored the Filter Cartridge
should be replaced .
4. Put on the filter cartridge cover and place the
filter cartridge to water inlet by turning it clock-
wise
Heat Button: Use this button to activate the heating system.
The heater does not stop heating the Spa until the current water temperature reaches 1°C higher
than the set temperature.
After the current water temperature drops 2°C below the set point temperature the heating sys-
tem will restart.
When the light of the Heat Button displays green, the heating system is activate
Heating system is capable of increasing approximately 1.5 to 2°F per hour.
NOTE: If the heating system is activated the filtration system will automatically start – This is
normal.
NOTE: After turning off the heating system the filtration system will still work. This is normal.
Caution:
Attention: When “HEATER” and “FILTER” both are on, only pressing “HEATER” button can switch
off filtering function but not “FILTER” button.
Bubble Button: Press this button to activate the massage system which has a 30-minute auto
shut off for 10 minutes feature.
The light of bubble Button displays green when activated.
(1) (2)
(3) (4)

10
Drainage
1. Turn off all the buttons on the control panel.
2. Connect the hose with the outlet in the inner wall of the spa to drain, and the hose with the inlet to
absorb water.
3. Turn on the filter pump.
4. Tilt the spa will allow the spa to thoroughly drain.
5. Press the filter button once the spa is completely drained.
Maintaining Spa Water
Poor water quality can be extremely hazardous to your health. We recommend you do following things:
A: Clean your filter cartridge at least once a time after it worked continuously for 72~120 hours. The filter
cartridge should be replaced at least once a month depending on use
B: Change water every few days or use appropriate pool chemicals.
All spas require the use of pool chemicals. Please consult your local pool supply retailer for more informa-
tion about chemical maintenance. Pay close attention to the chemical manufacturer’s instructions. Spa
damage resulting from misuse of chemicals and mismanagement of spa water is not covered by the
warranty.
a. Water Balance
We recommend maintain your water pH between 7.2 and 7.8, total alkalinity between 80 and 120ppm and
free chlorine between 3 to 5ppm. Purchase a test kit to test your water chemistry before each use of the
spa, no less than once per week. Low pH will damage to the spa and pump. Damaged resulting from
chemical imbalance is not covered by the warranty.
b. Water Sanitation
Water Sanitation is the responsibility of the spa owner, achieved through the regular and periodic (daily, if
necessary) addition of an approved sanitizer. The sanitizer will chemically control the bacteria and viruses
present in the fill water or introduced during use of the spa.
Cleaning the spa
Detergent residues and dissolved solids from bathing suits and chemicals will gradually accumulate in
the Spa’s water. To clean the Spa, use soap and water then rinse.
NOTE: DO NOT use hard brushes or abrasive cleaners.
INLET
(2) (3)
OUTLET

11
Spa Repair
If the Spa is torn or punctured use the provided Repair Patch. Dry the area to be repaired. apply the glue in
the accessory bag to the repair patch and then attach it onto the damaged area. Smooth the surface to
remove any air bubbles. A secure unnoticeable repair can usually be made.
Spa Storage
Make sure all water is drained from the Spa and control box. This is essential to extend the life of the spa.
We recommend the use of a wet/dry vacuum to blow out or suck up water from the Spa pipes and Pump
lines. Remove the Filter Cartridge. It is recommended you store the spa in its original package in a warm
dry place.
NOTE: Plastic becomes brittle and susceptible to breakage when exposed to subzero temperatures. Freez-
ing can severely damage the Spa. Improper winterization of your Spa may void your warranty.
TROUBLESHOOTING
ORPC strives to provide the most trouble-free spas on the market. If you experience any problem whatsoever,
do not hesitate to contact us or our authorized dealer.
Here are some helpful tips to help you to diagnose and rectify some common sources of trouble.
Problems Probable Causes Solutions
Co ntrol bo x does n ot operate
-Power failure
-GFCI tripped
-GFCI broken
-Check power source
-Reset GFCI/Check if the home fixed wiring too thin
to afford 2300W.
-Call for service if it does not reset.
Control box does not heat properly
-Temperature set too low
-Dirty Filter Cartridge
-Improper water levels
-Heating element failed
-Set to a higher temperature (between 20-40ć)
-Clean/replace the Filter Cartridge in time
--Add water to specified levels
-Cal l for service
Bubble Massage System does not work -Pump is too hot
-30-minute auto shut off feature
activated
-Something is wrong with the control
box
-Unplug the Pump. After the Pump has cooled
insert the plug and press the bubble button to
activate
-Press the bubble Button to reactivate
-Call for service if it does not reset
Water Filtration not working -Di rty Fil ter Cartri dge
-Something is wrong with the control
box
-Clean/replace the Filter Cartridge in time
-Call for service if it does not reset
Spa leakage -Spa is torn or punctured -Use provided Repair Patch
Water not clean -Insufficient filtering time
-Dirty Filter Cartridge
-Improper water maintenance
-Increase filtration time
-Clean/replace the Filter Cartridge
-Refer to the chemical manufacturer’s instructions

12
DISPOSAL
1.The marking indicates that this product shall not be disposed with the general household
waste. Please contact your local community about collection points or ask your dealer.
2.This product contains valuable materials that can be recycled and contribute to a sustainable environment.
3.For recovery, recycling and dismantling information for this product, please visit us at www. the-mspa
com
WATER PROTECTION LEVEL
Warring: Water protection levels of Appliance at different product zones are different see the following
scheme.
NOTE - The measured zone dimensions are limited by walls and fixed partitions.
Figure 702A - Zone dimensions of swimming pools and paddling pools
SAFETY & ANNOUNCEMENTS
a. A local supplementary equipotent bonding shall connect all extraneous conductive parts in Zones 0,1
and 2 with protective conductors of all exposed conductive parts situated in these zones;
b. The measures of protection by non-conducting location and by earth-free equipotent bonding are not
permitted;
c. Electrical equipment shall have at least the following degrees of protection:
In Zone 0: IPX8
In Zone 1: IPX5
In Zone 2: IPX4
d. Junction boxes shall not be installed in Zones 0 and 1 except in zone 1,where permitted for SELV circuits.
e. In Zones 0 and 1, no switchgear and accessories shall be installed;
f. The transformer must be located outside zone1
LIMITED WARRANTY - TERMS & CONDITIONS
This warranty extends to the original purchaser only. The warranty period commences on the original
purchase date through 6-12 months according to the different parts. This warranty is not transferable to
subsequent purchasers. This warranty is subject to the obligations, limitations, and exclusions listed
below.
1.5m
Zone 1 Zone 1Zone 2 Zone 2
Zone 0
Zone 0
Zone 0
1.5m 1.5m2.0m2.0m
2.5m 2.5m
1.5m

13
Extent of warranty
3 months warranty on tub, (For B-110)
6 months warranty on tub, (For B-130, B-140)
12 months for electric parts.
Obligations of Purchaser
The purchaser must establish, by dated sales slip, invoice, or installation receipt, the date of original
purchase. In order to supply the customer with the most up to date service we respectfully request the
purchaser to register their purchase by completing the attached Warranty Registration Card and mail it to
the manufacturer within 15 days of date of receiving the purchase, or submit via our website at www.the-
mspa.com.
Transportation costs incurred to and from the manufacturer or authorized service center is the responsibil-
ity of the purchaser. This includes freight charges for parts shipped to your dealer or service center. All
costs for the removal or reinstallation of parts are the responsibility of the purchaser. You may be subject
to dealer service charges. Factory labor is defined as labor required to test and to perform repairs to
components returned to factory at customer expense provided defective components are returned within
specified warranty period.
Limitations and Exclusions
The warranty is a limited warranty. It covers the Spa pool itself for the period stated. This warranty negates
or limits all other warranties implied or expressed, except for those, which cannot be negated or limited by
law of the state in which the product is used. The manufacturer does not authorize of permit any party,
including its agents, distributors or dealers to assume for it any other obligations or liability. In no event will
the manufacturer be liable for any claim for damages arising from the use or loss of use, installation, or
repair of the Spa pool including, but not limited to freight damage, punctures, cuts in vinyl, water and/or
sewage costs, freeze damage, or water damage to surrounding areas, rooms, furnishings or landscaping.
The purchaser is responsible for providing adequate access to all areas surrounding the Spa so that
service may be properly performed. Product specifications are subject to change without notice.
Acts Invalidating Warranty
This warranty is void if the Spa pool has been altered, misused, abused or has been repaired by an
unauthorized person, or is not installed according to the factory instructions. Other acts that will void the
warranty are operating the Spa without water or improper water level, use of an extension cord, improper
chemical maintenance, burying the Spa below ground level, damage from ice or freezing, low voltage or
excess voltage. This warranty gives you specific legal rights. Specifications are subject to be changed
without notice.
Manufactured By:
ORIENTAL RECREATIONAL PRODUCTS (SHANGHAI) CO.,LTD.
1699 Daye Road, Wuqiao, Fengxian, Shanghai, China

Canada
Warrantycare.com
US- Consumers
888-521-6183
US-Dealers
888-661-6772
www.mspausa.com
32