DataComm Electronics 45-0032-WH User manual

IMPORTANT INSTRUCTIONS:
This product is designed for retrofit work only
because the electrical outlet box cannot be
attached to a stud.
WARNING:
Before running 12/2 w/ ground UL approved
building wireto the Recessed Low Voltage Media
Plate with 20 Amp Duplex Receptacle, be sure the
power is off by switching the circuit breaker to off
or removing the fuse(s). Test the power to make
sure the power is off. Be sure to install the Media
Plate with Duplex 20 Amp Receptacle in
accordance with the National Electrical Code
(NEC) local codes.
WARNING
DataComm Electronics’ products shall be installed and used only as indicated in DataComm Electronics’ product instruction sheets.
Instruction sheets are available online at www.datacommelectronics.com.
CAUTION
For shock protection, this device must be properly grounded.
Use copper wire only with this device.
IMPORTANT INSTRUCTIONS
Read and understand all instructions.
Follow all warnings and instructions marked on the product.
Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet basement, or near a
swimming pool.
SAVE THESE INSTRUCTIONS.
Instruction / Installation Sheet
Recessed Low Voltage Media Plate
with 20 Amp Duplex Receptacle
Part # 45-0032-WH
DataComm Electronics, Inc.
6349 Peachtree Street
Norcross, GA 30071-1725
888.223.7977
770.662.8205
www.DataCommElectronics.com
Parts Included:
• Recessed Low Voltage Media Plate
• Steel Electrical Box
• 20 Amp/125 Volt Tamper Resistant Duplex Receptacle
• Four (4) Electrical Box Mounting Screws
Tools Required:
• Drill with Phillips Bit or Phillips Head Screw Driver
• Pen or Pencil
• Sheetrock Saw or Utility Knife
• 6 Ft. Tape Measure
Use the Recessed Low Voltage Media Plate with 20 Amp Duplex Receptacle to install low voltage cables
behind your HDTV or other display device. The plate can be installed upright or sideways (see Installation
Diagram below).
Features of the Recessed Low Voltage Media Plate with 20 Amp Duplex Receptacle include:
• HDTV/display device plug recesses completely into the wall when plugged into the Media Plate
• 20 Amp Duplex Receptacle and Steel Electrical Box for commercial requirements
• Large low voltage pass through opening for multiple low voltage cables
Page 1 of 3 11/15/13
Installation Diagram

Fig. 1
Fig. 2
Instruction / Installation Sheet
Recessed Low Voltage Media Plate
with 20 Amp Duplex Receptacle
Part # 45-0032-WH CONTINUED
Installation Instructions:
Page 2 of 3 11/15/13
888.223.7977
770.662.8205
www.DataCommElectronics.com
Figure 1:
Top view - shows needed space between the
drywall and the studs. Receptacle side of the Media
Plate should be 3” from the stud but no more than 5”
(review picture carefully).
Figure 2:
Cut out the supplied template on page 3 of this instruction sheet. Place the template on
the wall in the desired install location. Using your pen or pencial, trace the template on the
wall. Using a drywall saw or utility knife, cut a hole in the drywall the size of the template.
See Figure 1 before tracing your opening. Remember, this wall plate is designed to be
installed between the studs. It cannot be installed on top of a stud.
Figure 3:
Run the source of power to the included steel electrical box. Be sure to follow all local
electrical codes.
Figure 4:
Connect the suplied 20 Amp Duplex Receptacle to a piece of 12/2 w/ ground UL
approved electrical building wire that you have pulled from a power source. Strip off
approximately 3 inches of the outer jacket of the wire. Be careful not to cut the jacket of
the inner wires. Connect the hot line (black) wire to the brass colored terminal screw and
neutral (white) wire to the silver colored terminal screw. Be sure to connect the grounding
(green) or bare grounding wire to the green colored terminal screw. Once you have wired
the 20 Amp Duplex Receptacle, screw it into the Steel Electrical Box until the receptacle
is firmly secured.
Figure 5:
Use the four provided screws to secure the Steel Electrical Box and Receptacle to the
mounting studs on the backside of the Recessed Low Voltage Media Plate.
Figure 6:
Important: Before installing the Media Plate into the template opening, make sure to pull
your low voltage cables through the low voltage cable opening.
After low voltage pass through: Starting with the receptacle side of the Media Plate
slowly slide it into the opening. Swing the opposite side of the plate into position until the
entire Media Plate is flush with the wall. Now screw down the screws with wings; these
wings fasten tightly against the back of the drywall.
Figure 7:
Your new Recessed Low Voltage Media Plate with 20 Amp Duplex Receptacle is now
installed and ready for the TV mount to be installed. Install your TV mount bracket per the
TV bracket manufacturer’s instructions.
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7

ONLY LICENSED PROFESSIONALS SHOULD INSTALL THIS PRODUCT
This product is patent protected by U.S. Patent numbers D553475, D554475 and 7390964.
RoHS Compliant.
Instruction / Installation Sheet
Recessed Low Voltage Media Plate
with 20 Amp Duplex Receptacle
Part # 45-0032-WH CONTINUED
Page 3 of 3 1 / /13
888.223.7977
770.662.8205
www.DataCommElectronics.com
ETL LISTED
CONFORMS TO
UL STD 514C
7-1/4”
TEMPLATE
45-0032-WH Recessed Low Voltage
Media Plate with Duplex 20 Amp Receptacle
ACTUAL SIZE
CUT ALONG DOTTED LINE 
7-1/8”