Delano Darcy 413/4783 User manual

Dimensions
Width - 61.7 cm
Depth - 42 cm
Height - 190.5 cm
Darcy - Tower with 2 Doors
413/4783
Important - Please read these instructions fully before starting assembly
Issue 1 - 03/06/2015 1
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400 800

!Safety and Care Advice
Important - Please read these instructions fully before starting assemb ly
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately 47 kgs.
Please lift with care.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: if required the next
page can be cut out and used
as reference throughout the
assembly .Keep this page with
these instructions for future
reference.
2
• Check you have all the
components and tools listed on
pages 3 and 4.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels during assembly,
this could cause damage.
• Assemble the unit as close
to its final position (in the same
room) as possible.

Please check you have all the panels listed below
3
1
Left side
(181.4 x 41.8cm)
2
Right side
(181.4 x 41.8cm)
3
Top
(61.7 x 42cm)
4
Bottom
(61.7 x 42cm)
5
Horizontal
partition
(58 x 39.8cm)
7
Door
(134.4 x 57.4cm)
6
Shelf x 2
(57.9 x 34cm)
8
Flap
(57.4 x 44cm)
9
Front glass
(123.4 x 46.4cm)
10
Rear top
(136.5 x 59.3cm)
11
Rear bottom
(46.2 x 59.3cm)
12
Long plinth x 2
(51.3 x 5cm)
13
Short plinth x 2
(33 x 5cm)
Component - Panels If you have damaged or missing components
call the Customer Helpline: 0845 6400 800

Components - Fittings
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
4
Wooden dowel x 24 (8x35) Hinge plate x 5 Door hinge x 5
CC
A C
4x13mm Screw x 10
D
B
Cap x 8
F
3x16mm Screw x 20
N
3,5x16mm Screw x 14
O
Stabilizer x 10
S
Handle x 2
J
Locking nut x 8
( 15x13)
E
H
(7x50) Hexagon bolt x 4
Metal dowel x 8
G
Cap x 4
I
3.5x27mm Screw x 4
HL
Allen key x 1
M
Feet x 4
P
Flap stay x 2
Q
Mounting bracket x 4
T
Height adjuster x 1
V
4x16mm Screw x 1
K
Wall Bracket x 1
R
Washer x 3
U
Shelf support x 11
W
Glass clip x 10
X
Plug plates x 6
Y
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
5 & 8mm Suitable drill bit
(for use with wall plug)
Eye protection
(when using a
hammer or glue)
Tools required
Punch

WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
b: Attaching flap stay
flap stay usingAttach
screws .
5
Assembly Instructions
Step 1Step 1
1
1
1
1
E
G
A
b:
a:
OO
O
Q
Insert locking nuts
into the left side panel
.
Insert wooden dowels
into the left side panel
.
Screw metal dowels .
Insert shelf support
into the left side panel
G
G
G
A
A
A
A
A
EE
E
W
W
W
W
W
Q
Q
O
a: Inserting dowels
and locking nuts

Assembly Instructions
Step 1Step 2
a:
6
O
O
O
Q
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
E
G
A
b:
Insert locking nuts
into the right side panel
.
Insert wooden dowels
into the right side panel
.
Screw metal dowels .
Insert shelf support
into the right side panel
G
A
A
A
E
E
E
W
Q
Q
O
2
2
2
2
W
W
W
W
A
A
G
G
a: Inserting dowels
and locking nuts
b: Attaching flap stay
flap stay usingAttach
screws .

Assembly Instructions
Step 1Step 2Step 1Step 3
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
7
Screw metal dowels
into the top .
Insert shelf support
into the top.
3
G
G
G
G
G
G
E
A
B
B
B
B
4
4
3
5
5
Insert locking nuts
into the horizontal partition
.
Insert wooden dowels
into the horizontal partition
.
Rotate horizontal partition.
Insert shelf support
into the horizontal partition.
5
5
A
A
A
A
A
E
E
E
E
E
W
W
W
W
W
Attach “hinge plates"
into the bottom .
Finished
Finished
front edge
front edge
a: Inserting dowels
and locking nuts

Assembly Instructions
Step 1
Step 1
Step 2
Step 2
Step 1
Step 1
Step 4
Step 5
8
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
dowels in place.
!
Insert wooden dowels
into the long plinth .
Repeat with short
plinth .
A
A
A
A
A
A
A
12
12
13
13
A
C
D
D
C
C
x2
x2
8
8
Fitting hinges to flap
Fix 2 hinges to the
flap using screws .
CD
a: Inserting dowels

Assembly Instructions
Step 6
Attach front glass .
into the door using
glass clamp & screw
Attaching glass
Step 7
9
N
N
X
X
X
X
X
X
X
X
X
X
X
X
9
9
7
7
9
7
C
C
C
7
Fitting hinges to door
Fix 3 hinges to
the door using screws .
CD
C
D
D
WARNING!
We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the
unit. Only use hand
screwdrivers.
!

Assembly Instructions
Step 8
Step 9
a: Attaching plinth
Attach feet to the
long plinth
Attach long plinth
to the short plinth .
b: Attaching plinth
Attach long plinth
& short plinth to the
bottom .
4
4
4
P
PP
P
P
12 12
12
12
12
12
12
13
13
13
13
13
13
13
13
12
12
13
13
a:
b:
WARNING!
Please wear
goggles or
protective
eyewear whilst
hammering
sliders in place.
!
10
T
T
T
O
O
T
T
TT
Mounting bracket
Place mounting
bracket onto the
assembly as shown.
Mark holes with a
punch and fix the
bracket with screws .
T
O

Assembly Instructions
Step 10
11
Finished
front edge
A
E
G
E
M
F
F
F
M
M
E
E
Attaching panels
Attach left side panel
to the horizontal partition
Attach right side panel
to the horizontal partition .
Use the allen key to
turn locking nuts
clockwise to lock.
Cover locking nut
with caps .
1
5
5
5
5
2
Step 11
12
Attaching top
Attach top to the
sides and
Use the allen key to
turn locking nuts
clockwise to lock.
Cover locking nut
with caps .
3
3
1
1
2
2

Step 12
Step 13
12
H
M
J
H
I
Inserting rear panel
Slide rear panels and
into the grooves of
sides , and top .
4
Attaching bottom
Attach bottom to the sides
using hexagon bolt
& allen key .
Cover bolts with caps .
10
11
4
10
11
2
21
1
H
H
H
H
H
M
I
H
Assembly Instructions
3
10 11

Step 14
IMPORTANT !
Cabinet MUST
be “square”
when rear panel
is attached.
!
S
Fixing back panels
Fix rear panel
to back of tower
using stabilizer .
Attach washers
using screw .
Place wall bracket
onto the assembly as
shown.
Mark hole with a punch
approximately in the
middle of the slot in the
bracket and fix the
bracket with screw .
U
UUU
N
S
S
S
S
S
S
S
S
S
SS
U
N
10
11
3
13
R
K
R
R
K
Assembly Instructions

Assembly Instructions
Step 15
R
R
V
V
3
4
4
4
14
Fixing to wall
It is recommended that
the tower is fixed to
a wall.
With help, move
tower into position.
Mark fixing hole on wall
and remove tower.
Drill a hole on the
marking on the wall.
Reposition tower.
Fix wall bracket
to wall.
Place a spirit level on
bottom .
Where necessary, insert
height adjuster to
make bottom level.

Step 16
B
B
B
B
B
B
B
B
B
Y
Y
Y
Y
Y
Y
Y
Y
15
Assembly Instructions
a:
For door to open from
the left, attach hinge
plates on the right.
Cover the mounting
holes on the left with
caps .
b:
For door to open from
the right, attach hinge
plates on the left.
Cover the mounting
holes on the right with
caps .
Y
Y
a: b:

HL
HL
HL
HL
HL
Step 17
16
Hinge
adjustment
B
C
B
C
Q
N
Q
N
If door is set to open from
right, please proceed to
step 18.
Hanging door
a: slot door hinges onto
‘hinge plates’.
b: Tighten screw
shown to lock hinges in
position.
If necessary, adjust
hinges, to adjust
position of door.
Fix flap stay to the flap
using screws .
Insert shelf .
If necessary, adjust
hinges, to adjust
position of flap.
Attach handles
using screws .
C
a:
b:
Q
N
J
J
J
6
6
6
7
9
HL
8
5
Assembly Instructions

HL
HL
HL
HL
Step 18
B
C
B
C
Q
N
Q
N
a:
b:
J
J
6
6
7
9
8
5
17
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline: 0845 6400 800
HL
Hanging door
a: slot door hinges onto
‘hinge plates’.
b: Tighten screw
shown to lock hinges in
position.
If necessary, adjust
hinges, to adjust
position of door.
Fix flap stay to the flap
using screws .
Insert shelf .
If necessary, adjust
hinges, to adjust
position of flap.
Attach handles
using screws .
C
Q
N
J
6
HL
Hinge
adjustment