PB TEEN Half-Pipe Storage User manual

1/12
www.pbteen.com
Half-Pipe Storage
PRE-ASSEMBLY:
•Please read all instructions before assembling.
•Two-adult assembly is recommended.
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
•Do not use power drill as it may cause cracking
PARTS INCLUDED:
E – Side Panel – 2 pcs F – Half-Pipe Top – 2 pcs G – Half-Pipe Base – 2 pcs
H – Storage Base – 2 pcs
HARDWARE INCLUDED:
I – Hex Bolt – 12 pcs J –Connecting Screw – 16 pcs K – Connecting Sleeve – 16 pcs
(1/4”x25mm) (5/32”x28mm) (5/32”x14mm)
O – Allen Key – 1 pc P– Wooden Dowel – 4 pcs
(8x30mm)
TOOLS REQUIRED (but not included):
Phillip Head Screwdriver
ASSEMBLY:
1. Aligning the pre-drilled holes on the Half Pipe Base (G) to the pre-drilled holes on the top of the
Storage Base (H). Insert 4 Hex Bolts (I) through the Storage Base (H) and into the Half Pipe Base (G)
as shown below. Tighten using the Allen Key (O) and repeat for the other side.
Figure 1

2/12
www.pbteen.com
2. Un-lock wheels under Storage Base (H) as shown below. Connect the 2 bases together by inserting 4
Connecting Sleeves (K) through the pre-drilled holes on one of the bases and insert 4 Connecting
Screws (J) into the pre-drilled holes on the other base. Tighten using a Phillip Head Screwdriver as
shown in Figure 2.
3. Aligning the pre-drilled holes on the Half Pipe Top (F) to the pre-drilled holes on the top of the Half
Pipe Base (G). Insert 2 Hex Bolts (I) through the Half Pipe Top (F) into the Half Pipe Base (G) as
shown below in Figure 3. Tighten using the Allen Key (O) and repeat for the other side.
4. Place 2 Wooden Dowels (P) into the pre-drilled hole on back of Half Pipe Base (G) shown in Figure 4.
Insert the other end of the Wooden Dowel (P) into the corresponding pre-drilled holes on the Side
Panel (E). This allows the Side Panel to align properly for the other pre-drilled holes.
Fi
g
ure 2
Fi
g
ure 3
Fi
g
ure 4

3/12
www.pbteen.com
5. Insert 2 Connecting Sleeves (K) through the pre-drilled holes on the Half Pipe Top (F) and insert 2
Connecting Screws (J) into the pre-drilled holes on the Side Panel (E). Tighten using a Phillips Head
Screwdriver as shown in Figure 5.
6. Insert 4 Connecting Sleeves (K) through the pre-drilled holes on the Storage Base (H) and insert 4
Connecting Screws (J) into the pre-drilled holes on the Side Panel (E). Tighten using a Phillips Head
Screwdriver as shown in Figure 6.
7. Repeat steps 4-6 for other Side Panel (E)
8. When the Half Pipe Storage is in desired location, lock wheels to prevent movement.
CARE INSTRUCTIONS:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Waxing is not recommended on lacquered finish.
•Hardware should be checked periodically for tightness.
Fi
g
ure 5
Fi
g
ure 6

4/12
www.pbteen.com
Half-Pipe Storage Left/Right Cabinet
PRE-ASSEMBLY:
•Please read all instructions before assembling.
•Two-adult assembly is recommended.
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
•Do not use power drill as it may cause cracking
PARTS INCLUDED:
A - Left Cabinet - 1pc C - Left Cabinet Door – 1 pc
B - Right Cabinet - 1 pc D - Right Cabinet Door – 1 pc
HARDWARE INCLUDED:
L – Bolt for Handle – 4 pcs M – Large Screw (for Hook) – 12 pcs N – Small Screw (for hinge) – 18 pcs
(5/32”x32mm) (#6x19mm) (#6x15mm)
R – Hook – 6 pcs S – Handle – 2 pc
TOOLS REQUIRED (but not included):
Phillip Head Screwdriver
ASSEMBLY:
1. Lie Left Cabinet (A) on its side with the pre-drilled holes on the floor and the side with the door
magnet off the ground. Place Left Cabinet Door (C), mirror side down and align the hinges with the
pre-drilled holes on the Left Cabinet (A) as shown below in Figure 2. Repeat for Right Cabinet (B) and
Right Cabinet Door (D).
A
C
C
Fi
g
ure 1 D
B
D

5/12
www.pbteen.com
2. Starting with the center hinge on the Left Cabinet Door (C) place 3 Small Screws (N) through pre-
attached hinge into the pre-drilled holes located on the Left Cabinet (A); tighten using a Phillips Screw
Driver as shown below in Figure 2. Repeat for the other two hinges located on the Left Cabinet Door
(C). Repeat entire step for Right Cabinet (B) and Right Cabinet Door (D).
3. Assemble Hooks (R) by aligning the pre-drilled holes on the Hook (R) with the pre-drilled holes on
hook rail on the doors and inserting Large Screw (M), tighten using the Phillips Head Screwdriver as
shown in Figure 3.
4. Carefully turn cabinet’s uprights. Attach Handles (S) by aligning the handle over pre-drilled holes
located on the Cabinet doors. Insert Bolt (L) through pre-drilled holes on door into the holes on
handle; tighten using a Phillips Head Screwdriver as shown in Figure 4.
Figure 2
Fi
g
ure 3
Fi
g
ure 4