Deltech Fitness DF4400 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
DF4400
SQUAT RACK
Assembly Manual

K
E F G H
D
B C
FRONT TRIANGLE
FLANGE
QTY 4
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
DF4400
BOX CONTENTS
LADDER RACK
QTY 2
A
FOOT
QTY 2
REAR UPRIGHT
QTY 2
FRONT UPRIGHT
QTY 2
WEIGHT PLATE
SUPPORT
QTY 4
REAR TRIANGLE
FLANGE
QTY 4
UPPER TRIANGLE
FLANGE
QTY 2
I
LH & RH WEIGHT SUP-
PORT
QTY 1 EACH
CROSSMEMBER
QTY 2
J
RUBBER SHOE
QTY 4

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
DF4400
HARDWARE
M12 WASHER
QTY 76
O
M
M12 x 75MM BOLT
QTY 38
M12 LOCKNUT
QTY 38
P
ROUND CAP
QTY 4
Q
SQUARE CAP
QTY 2
R

ATTACH THE RUBBER SHOES (K) TO THE LEFT & RIGHT FEET (A)
TOOLS REQUIRED FOR ASSEMBLY
ADJUSTABLE WRENCHES OR METRIC SOCKET SET
(NOTE: THE NUTS USED ON THIS RACK ARE LOCK NUTS,
THIS MEANS YOU MUST TIGHTEN THEM DOWN PAST THE
PLASTIC INSERT.)
K
K
A

ATTACH THE FRONT TRIANGLE FLANGE (F) AND REAR TRIANGLE FLANGE (G)
TO THE FOOT USING M12 x 75MM BOLT (M), M12 WASHER (O), AND M12 LOCK-
NUT (P). DO NOT FULLY TIGHTEN NUTS AT THIS TIME. REPEAT FOR OTHER FOOT.
P
O
F
F
O
M
G

INSTALL THE FRONT UPRIGHT (C) INTO THE FRONT TRIANGLE FLANGES USING
M12 x 75MM BOLTS (M), M12 WASHERS (O), AND M12 LOCKNUTS (P).
INSTALL THE REAR UPRIGHT (B) INTO THE REAR TRIANGLE FLANGES USING M12
x 75MM BOLTS (M), M12 WASHERS (O), AND M12 LOCKNUTS (P).
INSTALL SQUARE CAP (R) INTO TOP OF FRONT UPRIGHT (C).
REPEAT FOR OTHER SIDE.
C
B
M
O
O
P
R

ATTACH LADDER RACK (D) USING M12 x 75MM BOLTS (M), M12 WASHERS (O), AND
M12 LOCKNUTS (P). INSTALL UPPER TRIANGLE FLANGE (H) WHERE FRONT AND
BACK UPRIGHTS MEET.
REPEAT FOR OTHER SIDE
P
Q
Q
M
R
O
P
O
N
H
D
M
O
O
P

INSTALL UPPER CROSSMEMBER (J) AND WEIGHT PLATE SUPPORT (E) TO REAR
UPRIGHT USING M12 x 75MM BOLTS (M), M12 WASHERS (O), M12 LOCKNUTS (P).
REPEAT FOR LOWER CROSSMEMBER.
M O
O
P
P
O
M
O
J
E
E

INSTALL ROUND CAPS (Q).
C
C
P
P
Q
Q
Q
Q
M
M
R
R
I
Q

TO INSTALL THE WEIGHT CATCHES, HOLD THEM SIDEWAYS AND INSERT THE
LOCK PIN INTO THE DESIRED HOLE AND SLIDE FORWARD. TO LOCK INTO PLACE
ROTATE DOWNWARD UNTIL IT LOCKS INTO PLACE IN THE FRONT UPRIGHT.
Q
Q M
R
I