Denver DSS-200 User manual

Instruction Manual
Read this manual carefully to get the excellent acoustics from this unit.
5.1 Power Amplified Home Theatre Speaker System
w/ Remote Control
DSS-200
R
R

SAFETY INFORMATION
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL,
WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO
ALERT THE USER TO THE PRESENCE OF UNINSULATED,
" DANGEROUS VOLTAGE ", WITHIN THE PRODUCT'S EN-
CLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO
CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL
TRIANGLE IS INTENDED TO ALERT THE USER TO THE
PRESENCE OF IMPORTANT OPERATING AND MAIN-
TENANCE (SERVICING) INSTRUCTIONS IN THE LITERA-
TURE ACCOMPANYING THE APPLIANCE.
Safety PrecautionsSafety Precautions
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
CAUTIONCAUTION
!!
!!
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1
SPECIFICATIONS
20
21. Size Of Subwoofer (WxHxD).........................200x335x400(mm)
Size and Net Weight:
22. Size Of Front Speaker (DxH)................................F86x1050(mm)
23. Size Of Centre Speaker (DxH).................................F86x350(mm)
24. Size Of Rear Speaker (DxH)..................................F86x1050(mm)
25. Net Weight.......................................................................22.8kg
Note: Specifications are subject to change for improvements.Note: Specifications are subject to change for improvements.
20. L/R Balance (Stereo)........................................................ 1.5dB

Caution: Please read carefully all the following important safe-
guards to ensure safe operation.
Caution: Please read carefully all the following important safe-
guards to ensure safe operation.
1. Read Instructions - All the safety and operating instructions should
be read before the appliance is operated.
2. Retain Instructions - The safety and operating instructions should
be retained for future reference.
3. Follow Instructions - All operating instructions should be followed.
4. Heed Warnings - All warnings on the appliance and in the opera-
ting instructions should be adhered to.
5. Power Source - The appliance should be connected to a power
supply only of the type specified in the operating instructions or
as marked on the appliance.
6. Power-cord Protection - Power-supply cords should be routed so
that they are not likely to be walked on or pinched by items placed
upon or against them, pay particular attention to cords at plugs,
convenience receptacles, and the point where they exit from the
appliance.
7. Water and Moisture - The appliance should not be used near water
(for example, near a bathtub, washbowl, kitchen sink, laundry tub,
in a wet basement, or near a swimming pool, etc.)
8. Ventilation - The appliance should be situated so that its location
or position does not interfere with its proper ventilation. Do not
use the appliance on a bed, sofa, rug or similar surface that may
block the ventilation openings.
IMPORTANT SAFEGUARDS
2 19
SPECIFICATIONS
1. Power Supply.........................................................AC 230V/50Hz
2. Power Consumption............................................................200W
5. Speaker Impedance (Subwoofer)........................................8 Ohm
6. Speaker Impedance (Satellite).............................................4 Ohm
3. Input Sensitivity (Subwoofer)...................................60mV 20mV
4. Input Sensitivity (Satellite)......................................300mV 50mV
11. Rear Speaker Power Output (RMS).................................15Wx2
7. S/N (A Weight)....................................................................³72dB
8. Subwoofer Power Output (RMS)..........................................50W
9. Front Speaker Power Output (RMS)..................................15Wx2
10. Centre Speaker Power Output (RMS)..................................15W
12. THD (1kHz, 1W)................................................................£0.5%
13. Bass (100Hz).................................................................... 8dB
14. Treble (10kHz).................................................................. 8dB
19. L/R Separation (1kHz)....................................................... 30dB³
15. Frequency Response (Subwoofer)..............40Hz~200Hz 5dB
16. Frequency Response (Front Speaker)........200Hz~20kHz 5dB
17. Frequency Response (Centre Speaker)......200Hz~20kHz 5dB
18. Frequency Response (Rear Speaker).........200Hz~20kHz 5dB

5. REAR SPEAKER SILENT
(1) Check whether the system is connected correctly with the
Rear speaker.
(2) Check whether the system is connected correctly with the audio
source.
(3) Check whether 2.1CH is selected as audio output.
(4) Check whether 3.1CH is selected as audio output.
TROUBLE SHOOTING
To improve the effect of the system, please note the following when
you connect the DVD player as the audio input.
1. When 5.1 channel audio input is selected, the DVD player should
be set as multi-channel and choose the proper Disc format.
2. This speaker system is 5.1 channel satellite speaker system, so in
the speaker setting (in DVD menu) for the DVD player, the front,
centre and surround speakers should be set as small, and set thesmall
subwoofer at on status to allow it.on
If the detailed instruction about DVD player setting is required, please
read the instruction manual carefully.
SUPPLEMENT
18
9. Heat - Keep the appliance away from heat sources such as radiators,
heat registers, stoves, or other appliances (including amplifiers)
that produce heat.
10. Nonuse Periods - The power cord of the appliance should be un-
plugged from the outlet when left unused for a long period of
time.
11. Damage requiring service - The appliance should be serviced by
qualified service personnel when:
a/ The power-supply cord or the plug has been damaged; or
b/ Objects have fallen or liquid has been spilled into the appliance;
or
c/ The appliance has been exposed to rain; or
d/ The appliance does not appear to operate normally or exhibits
a marked change in performance; or
e/ The appliance has been dropped, or the enclosure damaged.
12. Servicing - The user should not attempt to service the appliance
beyond that specified in the operating instructions. All other ser-
vicing should be referred to qualified service personnel.
13. Clean only with dry cloth.
14. Do not defeat the safety purpose of the polarized or grounding-
type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third
grounding prong. The wide blade or the third prong are provided
for your safety. If the provided plug does not fit into your outlet,
consult and electrician for replacement of the obsolete outlet.
15. Unplug this apparatus during lightning storms or when unused
for long periods of time.
IMPORTANT SAFEGUARDS
3

TROUBLE SHOOTING
1. NO OUTPUT
(1) Check whether the system is connected correctly.
(2 ) Check whether the Volume is set at minimum. Adjust it accordingly.
(3) Check whether the Audio Input is in PLAY mode.
3. FRONT RIGHT SPEAKER SILENT
(1) Check whether the system is connected correctly with the Front
Right speaker.
(2) Check whether the Balance function is switched off. Adjust it
accordingly.
(3) Check whether the system is connected correctly with the audio
source.
2. FRONT LEFT SPEAKER SILENT
(1) Check whether the system is connected correctly with the Front
Left speaker.
(2) Check whether the Balance function is switched off. Adjust it
accordingly.
(3) Check whether the system is connected correctly with the audio
source.
17
4. CENTRE SPEAKER SILENT
(1) Check whether the system is connected correctly with the Centre
speaker.
(2) Check whether the system is connected correctly with the audio
source.
(3) Check whether 2.1CH is selected as audio output.
5. REMOTE SENSOR: Remote Receiver.
3. INPUT Button.
7. VOL-: Volume Down.
1. 2CH: 2 Channel Input Indicator.
2. 5.1CH: 5.1 Channel Input Indicator.
9. MUTE: Power Standby .and Mute Indicator
6. STANDBY: Power Standby.
10. SURR. A: 3D Stereo Indicator.
11. SURR. B: 5.1 Stereo Indicator.
4. SURROUND: Surround Sound Decoder.
8. VOL+: Volume Up.
FRONT PANEL - CONTROLS AND FUNCTIONS
1
2
3
4
56
7
8
9
10
11
4
2CH
5.1CH
INPUT
REMOTE SENSOR
VOL+
STANDBY MUTE
VOL-
5.1 R E A D Y5.1 R E A D Y
AC-3
SURROUND
SURR. A
SURR. B
R

13. Stereo Left Audio Input.
12. 5.1CH Subwoofer Audio Input.
REAR PANEL - CONTROLS AND FUNCTIONS
15. 5.1CH Centre Audio Input.
16. Speaker Output.
FR: Front Right Speaker Output.
FL: Front Left Speaker Output.
C: Centre Speaker Output.
RL: Rear Left Speaker Output.
RR: Rear Right Speaker Output.
14. Stereo Right Audio Input.
5
17
18
12
20
19
13
14
15
16
22
21
16
K. MUTE Selection
1. Press the MUTE button (33) on the remote controller once to
keep the performance silent.
2. MUTE indicator (9) on the front panel will then light up and flash.
3. Press it again to resume the performance.
J. 5.1 CHANNELS INPUT Selection
1. Connect the system properly. 5.1 Channels audio output must
comply with 5.1 Channels audio input. (Note: AC-3/dts willNote:
decode 5.1 Channels output.)
2. Press INPUT button (25) on the remote controller to shift the
status for audio input to 5.1CH channels input.
3. Adjust all output settings including VOLUME, BASS, TREBLE
(if necessary) now to enjoy the wonderful and tremendous Home
Theatre effects.
2. Press RR - button (37) on the remote controller to minimize the
Rear Right Speaker output and STANDBY indicator (9) will light
up and flash.
OPERATING INSTRUCTION - MAIN UNIT
L. PRESET Selection
Press on PRESET button (34) on the remote controller will reset
all settings including BALANCE, CENTRE Speaker output, REAR
Speaker output to 0dB status preset by the manufacturer.
the Rear Right Speaker output and STANDBY indicator (9) will
light up and flash.
POWER
ON
OFF AC~230V/50Hz
2CH 5.1CH INPUT
LWRL FL
CRR FRR
FR FL CRL RR
SPEAKER OUTPUT
SERIAL NO:
5.1 Power Amplified Home Theatre
Speaker System w/ Remote Control
POWER SOURCE :AC~230V/50Hz
MODEL NO. :DSS-200
www.denver-electronics.com
POWER CONSUMPTION:200W
R

22. 5.1CH Rear Right Audio Input.
21. 5.1CH Front Right Audio Input.
20. 5.1CH Front Left Audio Input.
REAR PANEL - CONTROLS AND FUNCTIONS
17. AC Power Cord.
18. Power On/Off Switch.
19. 5.1CH Rear Left Audio Input.
6
OPERATING INSTRUCTION - MAIN UNIT
SURROUND ModeSURROUND Mode SURR. A IndicatorSURR. A Indicator SURR. B IndicatorSURR. B Indicator
3.1CH Stereo
5.1CH
5.1CH (Strengthened)
On
On On
OnOff
Off
I. REAR RIGHT SPEAKER Selection
1. Press RR + button (36) on the remote controller to maximize
H. REAR LEFT SPEAKER Selection
1. Press RL + button (27) on the remote controller to maximize
the Rear Left Speaker output and STANDBY indicator (9) will
light up and flash.
2. Press RL - button (29) on the remote controller to minimize the
Rear Left Speaker output and STANDBY indicator (9) will light
up and flash.
G. CENTRE SPEAKER Selection
1. Press C + button (28) on the remote controller to maximize the
Centre Speaker output and STANDBY indicator (9) will light up
and flash.
2. Press C - button (38) on the remote controller to minimize the
Centre Speaker output and STANDBY indicator (9) will light up
and flash.
15
Note: (1) Rear speakers output are off when 3.1CH Stereo mode is
selected.
(2) The system is based on 2.1 Channels output. SURROUND
is of no function at 5.1 Channels status.
Note: (1) Rear speakers output are off when 3.1CH Stereo mode is
selected.
(2) The system is based on 2.1 Channels output. SURROUND
is of no function at 5.1 Channels status.
SETTING UP THE ALUMINIUM DIE-CASTING SPEAKERS
Remove the base, aluminium speakers, screws, and rubber feet
from the packaging. Now you can set it up as follows:
1. Place the base at the bottom of the speaker pole, insert and
tighten the screws to secure the base to the speaker.
2. Stick the rubber foot on the base.

SYSTEM CONNECTION INSTRUCTION
Video In
To Stereo Output
(Optional)
Video Out DVD Player
7
Woofer Rear-L
Rear-R
Front-L
Front-R
Center
Optical
Audio Out
Rear-R
Center
Woofer Rear-L Front-L
Coaxial Front-R
Video Out
Scart out
Video S-Video UVY
Manufactured under license from Dolby Laboratories.
"Doldy","Dolby Digital", and the double-D symbol are
trademarks of Dolby Laboratories. Confidential
Unpublished Works.
@1992-1997 Dolby Laboratories, Inc.
All rights reserved.
Apparatus Claims of U.S. Patent Nos.
4,631,603;4,577,216;4,819,098 and 4,907,093
licensed for limited viewing uses only.
RISKOF ELECTRIC SHOCK
DO NOT OPEN
WARNING !!
AC 100V~240V
50/60Hz
TV
OPERATING INSTRUCTION - MAIN UNIT
2. Press the BASS - button (32) on the remote controller to mini-
mize the Bass output. Standby Indicator (9) on the front panel
will light up and flash when the Bass Output is decreased to
Minimum accordingly.
F. SURROUND DECODER Selection
1. Connect and place Centre and Rear speakers properly.
2. Press on SURROUND button (4) on the front panel of the main
unit or (24) on the remote controller to select Surround Decoder
for Home Theatre system effects.
E. BALANCE Selection
1. Press the BALANCE L button (26) on the remote controller to
minimize the Left speaker output.
2. Press the BALANCE R button (35) on the remote controller to
minimize the Right speaker output.
3. Standby Indicator (9) on the front panel will light up and flash
when the Balance Output is adjusted almost to the Centre status.
D. TREBLE Selection
1. Press the TREBLE + button (39) on the remote controller to
maximize the Treble output. Standby Indicator (9) on the front
panel will light up and flash when the Treble Output is increased
to Maximum accordingly.
2. Press the TREBLE - button (40) on the remote controller to mini-
mize the Treble output. Standby Indicator (9) on the front panel
will light up and flash when the Treble Output is decreased to
Minimum accordingly.
14
POWER
ON
OFF AC~230V/50Hz
2CH 5.1CH INPUT
LWRL FL
CRR FRR
FR FL CRL RR
SPEAKER OUTPUT
SERIAL NO:
5.1 Power Amplified Home Theatre
Speaker System w/ Remote Control
POWER SOURCE :AC~230V/50Hz
MODEL NO. :DSS-200
www.denver-electronics.com
POWER CONSUMPTION:200W
R

SYSTEM CONNECTION INSTRUCTION
8
OPERATING INSTRUCTION - MAIN UNIT
13
C. BASS Selection
1. Press the BASS + button (30) on the remote controller to maxi-
mize the Bass output. Standby Indicator (9) on the front panel
will light up and flash when the Bass Output is increased to
Maximum accordingly.
A. Switch On/Off the Product
1. Before turning on the system, please connect it according to
the System Connection Instruction.
2. Connect AC power supply with this product.
(Caution: Power source must be consistent with this product.)(Caution: Power source must be consistent with this product.)
3. Press on the power switch button (18) on the Rear Panel of the main
unit to switch on the system, the standby indicator will light up.
Press it once again to switch off the unit. Then press the standby
button (6) on the main unit or button (23) on the remote controller
to enter the normal status. Press the button (6) or button (23) on
the remote controller once again to keep power in standby status.
B. VOLUME Selection
1. Press the VOL+ button (8) on the front panel of the main unit
or VOLUME + button (31) on the remote controller to maximize
the sound output. Standby Indicator (9) on the front panel will
light up and flash when the Volume is increased to Maximum
accordingly.
2. Press the VOL- button (7) on the front panel of the main unit
or VOLUME - button (41) on the remote controller to minimize
the sound output. Standby Indicator (9) on the front panel will
light up and flash when the Volume is decreased to Minimum
accordingly.
Use the SPEAKER OUTPUT jacks on the rear panel of main unit to
connect to the satellite speakers.
(Connection example)(Connection example)
FR FL CRL RR
SPEAKER OUTPUT
Front Right Speaker

OPERATING INSTRUCTION - CONTROLS AND FUNCTIONS
9
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
23. POWER: Power Standby.
24. SURROUND: Surround Decoder.
25. INPUT: Input Switch.
26. BALANCE L: Left Speaker Balance.
27. RL +: Rear Left Balance Output Up.
28. C +: Centre Output Up.
29. RL -: Rear Left Balance Output Down.
5. To properly use the remote controller, please put its front emitter
right at the receiving lattice (remote sensor) of the main system.
6. The normal and effective distance for operating the system by the
remote controller is 7 meters within the system, and at 30 angle
left or right diverged away from the system.
OPERATING INSTRUCTION - REMOTE CONTROLLER
12
__________
TREBLE
__
++
BASS
__
++
VOLUME
__
++
RR
PRESET
MUTE
BALANCE
L
++
RL
SURROUND
R
++
C
INPUT
POWER
++
DSS-200
R