Denver REP PR-5000 User manual
PR-5000 with weight storage + lat attachment
parts Included:
2 Uprights
4 Horizontal Braces
8 weight horns
Hardware Included:
4.3 In Bolt
x 24
Nut
x 24
Small Washer
x 44 Bulgy Screw
x 16
1.
If you are starting from an
already assembled rack,
remove the name plate to
make room for the weight
storage. If you are starting
with building your power rack,
full PR-5000 Power Rack
Assembly Instructions
available at repfitness.com.
Upright caps must also be
removed so that you can
properly secure any horizontal
braces at the highest point of
the uprights.
Attach horizontal braces to the
top and bottom of each side of
the back of the power rack. These
should be attached to the highest
and lowest holes of the uprights.
The same screw will be used that
is securing the
horizontal braces of the power
rack.
x4
x8
x4
2.
Connect uprights to
horizontal braces.
3.
(4.7 in)
x4
x8
x4
(4.3 in)
Weight Storage Parts + Hardware
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP
Denver, CO(720) 420-1731
Secure weight horns to each side
of weight storage uprights. Make
sure to leave enough space
between each horn so that the
diameter of the plates can fit
vertically in line with each other.
4.
x4
x8
x4
(3.2 in)
Attach lat crossbars to the top and
bottom of the back of the power rack.
These should be attached to the highest
and lowest holes of the uprights.
They will share the same screw that is
securing the horizontal braces of the
power rack.
5.
x8
x16
x8
(4.7 in)
parts Included:
2 Crossbraces
Top Pulley Brace
Bottom Pulley Brace
Bottom Foot
Weight Peg Crossbrace
Straight Bar Attachment
Lat Pull-Down Attachment
2 Poles
2 Pole Tubes
3 Carabiners
11.5 Cable
10.2 Cable
Hardware Included:
4.7 In Bolt
x 8 3.2 In Bolt
x 2
2.8 In Bolt
x 4
1.8 In Bolt
x 3
3.2 In Bolt +
Stoppers
x 3
Nut
x 20
Washer
x 44
.8 In Bolt
x 4
Pulley
x 6
Lat Attachment Parts + Hardware
Denver, CO
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP
Secure pulley top and base
braces to crossbars.
6.
x2
x12
x6
(3.2 in)
(3.2 in)
x4
(2.8 in)
(2.8 in)
(2.8 in)
Feed cables through pulleys and secure the
pulleys in their designated locations. One end
of each cable will attach to the base of the lat
pull down to create a line of tension and the
other will have a carabiner to attach
pull-down accessories.
4.
x3
x3
x12
x6
(3.2 in)
(3.2 in)
(3.2 in)
(1.8 in)
(1.8 in)
(1.8 in)
(10.2 )
(11.5 )
Clip your pull-down accessories to the carabiners.
5.
morse code...(.-. . .--. ..-. .. - -. . … …). We are always here for our Customers! - Team REP
