DETAIL K2 OPG888E User manual

STUMP GRINDER ASSEMBLY GUIDE
MODEL: OPG888E
14IN 12 TEETH 14HP ELEC START
DETAIL K2 INC.
DK2 POWER USA
4301 S Valley View Blvd STE 10-11
Las Vegas, NV 89103
1-702-331-5353
1 SEC RAM SPEED
ATV TOWABLE
KOHLER ENGINE
14HP 12 TEETH
REV 1 –9-19-2019
DETAIL K2, INC.
1080 Clay Avenue Unit 2
Burlington, Ontario, Canada L7L0A1
DK2 USA EAST
6245 Industrial Parkway
Whitehouse, OH 43571
PARTS AND SERVICE 702-331-5353 OR WWW.DK2POWER.COM CONTACT US
OPG888E 14HP 12 TEETH
ELECTRIC START STUMP
GRINDER

STEP 1:
Open and unpack all items. Leave lots of working space.
Inspect all parts.
The STUMP GRINDER is shipped in a crate. Remove all sides
before you begin.
NOTE: UPON INSPECTION OF PARTS IF YOU FIND ANY DAMAGE OR MISSING
PARTS PLEASE CALL DK2 POWER AT 702-331-5353 OR CONTACT US VIA
OUR WEBSITE WWW.DK2POWER.COM
WE WILL REPLACE ANY MISSING PARTS TO YOU FREE
PLEASE DO NOT RETURN TO THE STORE
REV 1 –9-19-2019

STEP 2:
1. Install both wheels on the axel and secure semi tight with
lock nut. Allow wheel to spin freely.
2. The wheel with the large brake disk mounts on the same
side as the belt drive.
BRAKE WHEEL MOUNTS ON
THIS SIDE OF GRINDER
REV 1 –9-19-2019

STEP 3:
1. Install the TOW BAR and LOCK PIN.
2. UNIVERSAL TOW BAR WITH TROLLEY WHEEL
3. TROLLEY WHEEL DOWN OR REVERSE WITH HITCH DOWN
FOR TOWING.
REV 1 –9-19-2019

STEP 4:
1. Install the handle base
2. Use the 4 bolts and hardware provided
REV 1 –9-19-2019

STEP 5:
1. Install the BOW HANDLE
2. Use the long bolt and the spin handle provided
3. Align the teeth and tighten
REV 1 –9-19-2019

READ THE KOHLER ENGINE MANUAL SUPPLIED WITH YOUR
UNIT FOR FULL ENGINE OPERATION, SAFETY, AND
MAINTENANCE.
YOUR UNIT HAS A COMMERCIAL KOHLER ENGINE WITH A 3YR
PARTS AND SERVICE WARRANTY. FOR WARRANTY IN YOUR
AREA CONTACT THE NEAREST KOHLER DEALER.
VISIT WWW.KOHLERENGINES.COM FOR PARTS, SERVICE,
MANUALS, AND DEALER LOCATIONS.
REV 1 –9-19-2019

REV 1 –9-19-2019

REV 1 –9-19-2019
Ref Description Ref Description
1
Stop frame
25
Clutch spacer
2
Spacer bush
26
8 holes rubber
3
Top handrail
27
Main frame
4
Brake line fixed block
28
4 holes rubber
5
Brake line fixing piece,
plastic handle
29
4 holes rubber fix
6
Engine
30
External compression spring
7
Plastic battery box
31
Pin retaining sleeve
8
Tire
32
Brake cable limit plate
9
Universal wheel
33
The brake chuck
10
Flange
34
The brake pin
11
Tow hitch
35
Internal compression spring
12
Belt cover
36
Main frame handle
13
Cutter belt wheel
37
Brake line adjusting bolt
14
Bearing
38
Battery
15
Stright blade
39
Trailer rod holder
16
Right blade
40
The knife cover
17
Plate spacer right
41
Bottom handrail
18
Plate
42
Throttle cable
19
Plate spacer right
43
Stop switch
20
Left blade
44
Torsion Spring
21
Plate pulley spacer
45
Brake cable
22
Inner belt cover
46
Tow bar Pin
23
Belt cover spacer
47
Tow bar
24
Clutch
48
Chain

OPERATION –BEFORE TURNING KEY AND PULL STARTING ENGINE
CLEAR AREA OF ALL PEOPLE AND PROPERTY THAT COULD BE DAMAGED. THINK
SAFETY. CHIPS ARE FLYING PROJECTILES AND CAN CAUSE INJURY.
WEAR SAFETY GLASSES, HEARING PROTECTION, AND GLOVES
DO NOT WEAR LOOSE FITTING CLOTHES THAT COULD GET STUCK IN THE MACHINE
MOVING PARTS, ONLY CHIP WOOD, CHILDREN SHOULD NOT RUN THIS EQUIPMENT,
STAY ALERT OF YOUR SURROUNDING AND PERSONS THAT COULD APEAR IN THE
CHIP PATH WHILE YOU ARE WORKING.
UNIT IS A DIRECT DUAL BELT DRIVE. NO CLUTCH TO SLIP OR BURN UP
BUT YOUR BELTS WILL NEED TIGHTENED AND CHECKED ON A REGULAR BASIS TO
MAINTAIN 100% CUTTING POWER.
•Tip the Stump Grinder up with the cutters off the ground when pull starting.
12 CARBIDE CUTTERS 14 IN DIAMETER WHEEL FOR COMMERCIAL PERFORMANCE
SET THE BRAKE TO PIVOT ON WHEEL WHILE GRINDING. APPROACH STUMP FROM
THE TOP, CUTTING STRAIGHT DOWN INTO THE STUMP WITH THE 3.5 INCH WIDE
CUTTING TEETH. RAISE UP OUT OF THE CUT, MOVE OVER, PLUNGE AGAIN. REPEAT
ACROSS ENTIRE STUMP. MOVE SIDE TO SIDE TO FACE OFF THE STUMP. ADJUST
YOUR BOW HANDLE FOR COMFORT.
TIGHTEN ALL BOLTS AND TEETH BEFORE EACH USE. TEETH ARE NOT COVERED
UNDER WARRANTY. CLEAN ALL STONES AND ROCKS AWAYS FROM CUTTING STUMP
AREA, CHECK FOR METAL STAKES AND OR NAILS IN THE TREE STUMP BEFORE
CUTTING.
KOHLER ENGINES HAVE A LOW OIL SHUTOFF TO PROTECT THE ENGINE, TILTING THE
GRINDER MORE THAN 29 DEGREES ANGLE CAN CAUSE THE OIL TO ROLL BACK AND
THE LOW OIL SENSOR WILL SHUT THE ENGINE OFF. CUT YOUR STUMP 9 TO 10
INCHES OFF THE GROUND SO YOU DON’T TRIP THE SENSOR ON THE ENGINE.
READ AND OBEY ALL WARNING LABELS ON THIS MACHINE.
REMOVE THE UNIVERSAL TOW BAR WITH TROLLEY WHEEL WHEN GRINDING.

WHAT IS COVERED
DK2 Inc. warrants to the original purchaser of any DK2 product that it will be free and clear of manufacturing
defects in workmanship and materials under normal use and service for a period of one (1) year from the
date of the original purchase.
If within one (1) year from the original date of purchase this product fails due to defect in material or
workmanship. DK2 POWER outdoor power equipment is 1-year parts only warranty no labor.
Upon expiry of one (1) year, Detail K2 will have no further liability related to the product. Detail K2 does not
authorize any party, including its authorized distributors or dealers, to offer any other warranty on behalf of
Detail K2 Inc.
KOHLER ENGINES –KOHLER CH SERIES ENGINES COMMERCIAL 3 YR PARTS AND LABOR WARRANTY
see your Kohler manual for specific warranty.
DIESEL TRACTORS –Chassis component parts only, no labor, ENGINES –1 YR KOHLER WARRANTY
DK2 POWER OUTDOOR EQUIPMENT –1-Year parts only, no labor.
THIS WARRANTY DOES NOT COVER OR APPLY TO:
Damage to the product due to misuse, mishandling and abuse
(b) Improper installation, maintenance and storage
(c) Expendable parts such as nuts and bolts, pins and springs, wiring and switch components, hydraulic
hoses and fittings, cutting teeth, cutting chains, cutting blades, throttles, belts and tires.
(d) Normal wear and tear
(e) Consequential damage & incidental damages such as damage to persons or property
PROCEDURE FOR OBTAINING AN RETURN AUTHORIZATION
Within the one (1) year warranty period, the purchaser of the product must notify DK2 of the claimed defect
and provide proof of original purchase. At this time the validity of the claim will be determined, and if
approved replacement parts will be issued.
No returned product will be accepted under warranty unless accompanied by an RGA# issued by Detail K2
Inc.
RESOLUTION FOR A DEFECTIVE PRODUCT
DK2 POWER –Tractors, Chippers, Stump Grinders, Log Splitters, and Outdoor Power Equipment.
Call DK2 at 702-331-5353 in Las Vegas between 8am-4pm M-F Pacific Time.
PLEASE DO NOT RETURN TO THE STORE
YOU HAVE A 1 YEAR WARRANTY AND DK2 WILL REPLACE A DEFECTIVE PART FOR FREE
CALL US AT 702-331-5353 FOR FAST WARRANTY PARTS AND QUESTIONS
REV 1 –9-19-2019