Sencor SMG 4410WH User manual

EN MEAT GRINDER
SMG 4410WH

SMG 4410WH

A
2
3
4
5
1
6
B
9
2
3
4
5
76
8
10
11
1

C
2
3
1
D
2
3
4
1
7
6
8
5
E

F
G

H
3
2
1
4

I
1
2
3

- 1 - 10/2022
2022, .
EN Meat grinder
Important safety instructions
READ CAREFULLY AND STORE FOR FUTURE USE.
• General warnings
• This appliance may be used by persons with physical,
sensory or mental impairments or by persons with
insufficient experience and knowledge, if they are properly
supervised or have been informed about how to use the
appliance in asafe manner and understand the potential
dangers.
• This appliance may not be used by children. Keep the
appliance and its power cord away from children.
• Children must not play with the appliance.
• In the event that the power cord is damaged, have it
repaired at aprofessional service centre to prevent causing
adangerous situation. It is forbidden to use the appliance if
it has adamaged power cord.
• Be especially careful not to injure yourself on the screw
shaft and the cross blade when handling these parts,
especially when inserting or removing them from the
grinder and pay increased attention when cleaning them
so as not to injure yourself on the sharp parts.
• The surfaces of the appliance and its accessories that
come into contact with food must always be cleaned
according to the instructions in this user'smanual.

- 2 - 10/2022
2022, .
• Always turn off the appliance and disconnect it from
the power socket if you will not be using it and if you
will be leaving it without supervision, before assembly,
disassembly, cleaning or moving it.
• Before replacing the accessories or accessible parts that
move during use, turn the appliance off and disconnect it
from the power supply.
• Never push the food into the feed tube using fingers or
other utensils. Always use the provided pusher.
Warning:
Incorrect use may lead to injuries.
Electrical safety
• Before connecting this appliance to an electrical power socket, make sure that the voltage stated on its rating label corresponds to the voltage in
your power socket.
• Connect the appliance only to aproperly grounded socket. Do not use an extension cord.
• Fully unwind the power cord before use.
• Do not connect and disconnect the appliance'spower cord to and from the power socket with wet hands.
• Ensure that the power plug contacts do not come into contact with water or any other liquid. If precisely this happens, carefully dry the power plug
before using it again.
• Do not disconnect the appliance from the power socket by pulling on the power cord. This could damage the cord or the el. power socket.
Disconnect the power cord from the power socket by pulling on the plug.
• Do not place heavy items on the power cord. Make sure the power cord does not hang over the edge of atable and that it is not touching ahot
surface or sharp objects.
• Keep the power cord dry.
• Do not wind the power cord around the appliance.
• Always turn off the appliance and disconnect it from the power socket when not using it, when leaving it without supervision and before removing or
replacing accessories, and before cleaning, maintenance or storage.
• Do not repair the appliance yourself or make any adjustments to it. Have all repairs or adjustments of the appliance performed at an authorised
service centre. Tampering with the appliance during the warranty period may void the warranty.
• To prevent the risk of injury by electrical shock, never submerge the motor base unit and its power cord in water or any other liquid, or wash these
parts under running water.
• Always turn off the appliance and disconnect it from the power socket when you have finished charging it.
• If the appliance falls into water, under no circumstances continue using it, but rather hand it over to an authorised service centre for inspection.
• This appliance is designed for household use. Do not use it for commercial purposes or for other purposes for which it is not intended.
Safety during use
• This appliance is designed only for household use and constructed for processing the usual amount of food in ahousehold. Do not use this
appliance for commercial purposes.
• Do not use the appliance in an industrial environment or outdoors. Do not use it for any other purposes than those intended.
• The appliance is intended for domestic use and similar locations such as:
- kitchens in stores; offices and other workplaces;
- in agriculture;
- for guests of hotels, motels and other similar locations;
- in bed and breakfast establishments.
• This appliance is not intended to be operated using an external timer switch or aremote control system.
• Use the appliance and its accessories in accordance with the instructions contained in this user'smanual.
• Only use the appliance with the original accessories that came with it.
• Before every use, check the selected accessory for damage. Never use the appliance with adamaged accessory.

- 3 - 10/2022
2022, .
• Do not place the appliance or its accessories on an electric or gas stove or in its vicinity, on the edge of atable or on an unstable surface. Only place
the appliance on an even, dry and stable surface.
• Do not expose the appliance and its accessories to the outdoor environment, extreme temperatures, direct sunlight, excessive humidity or
excessively dusty environments.
• Do not place the appliance and its accessories near heaters, open fires or other sources of heat.
• Make sure that the appliance is correctly assembled before putting it into operation.
• Pay increased attention whenever handling the cross blade to prevent injury on the edges of the blade.
• Do not touch moving rotating parts during operation. Otherwise, this could result in injury.
• Always adhere to the operating time and the time intended for the cooling down of the appliance prior to it being started again. These times are
provided in this user'smanual in the relevant chapter.
• Do not turn on the appliance when it is empty. Incorrect use of the appliance may negatively affect its lifetime.
• Before disassembling the appliance into its individual parts, ensure that the appliance is disconnected from the electrical power socket.
• Do not use the appliance for crushing bones, nuts or other hard foods. Before using it, remove any bones, skin, cartilage, etc.
• Never process frozen food. Frozen food must be defrosted prior to being processed in the appliance.
• To prevent the appliance from clogging, push down gently on the pusher when adding the food into the feed tube.
• Always use the pusher supplied with the appliance. Never use your fingers or other items to push ingredients through the feed tube while the
appliance is running.
• Do not perform any maintenance on the appliance other than cleaning the individual components as described in this user'smanual.
• Never use an appliance that is damaged in any way.
• Do not use the appliance if it has fallen on the floor, if it was submerged in water, if it is not functioning correctly or if it is damaged in any other way.
• Do not submerge the motor base unit or its power cord in water or any other liquid, or wash these parts under running water. The motor base unit is
not designed to be washed in adishwasher.
• Do not use the appliance when it is not functioning properly or showing signs of damage.
• In order to prevent ahazardous situation arising, do not repair the appliance yourself or modify it in any way. Have all repairs performed at an
authorised service centre. By tampering with the appliance, you risk voiding your legal rights arising from unsatisfactory performance or quality
warranty.
• Store the appliance in adry environment.

- 4 - 10/2022
2022, .
• Thank you for purchasing aSENCOR brand product and we hope that
you will be happy with it.
• Prior to using this appliance, please read the user'smanual
thoroughly, even in cases, when one has already familiarised
themselves with previous use of similar types of appliances. Only use
the appliance in the manner described in this user’smanual. Keep this
user'smanual in asafe place where it can be easily retrieved for future
use. In the event that you hand this appliance over to somebody else,
make sure to also include this user'smanual.
• Carefully unpack the appliance and take care not to throw away any
part of the packaging before you find all its parts. We recommend
saving the original cardboard box, packaging material, purchase
receipt and responsibility statement of the vendor or warranty card for
at least the duration of the legal liability for unsatisfactory performance
or quality. In the event of transportation, we recommend that you pack
the appliance in the original box from the manufacturer.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DESCRIPTION OF THE APPLIANCE
A1 Grinder or grating attachment
lock/release button
A2 Hole for mounting the grinder
or the grating attachment
A3 Motor base unit
A4 On/Off switch
(ON/OFF)
A5 Reverse rotation button (REV)
A6 Anti-slip feet
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B1 Grinder
B2 Feed tube
B3 Grinding chamber
B4 Feeder tray
B5 Pusher
B6 Screw shaft
B7 Cross blade
B8 Coarse grinding plate (7 mm)
B9 Fine grinding plate (5 mm)
B10 Extra fine grinding plate (3
mm)
B11 Screw ring
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C1 Sausage stuffer attachment
C2 Separator (for making Kebbe)
C3 Shaper (for making Kebbe)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D1 Grater attachment
D2 Feed tube
D3 Grating chamber
D4 Pusher
D5 Grater for coarse grating
D6 Grater for fine grating
D7 Grater for very fine grating
D8 Grater for making slices
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PURPOSE OF USE
• The grinder is intended for processing meat, poultry, fish, fruits and
vegetables. Enables the grinding of all types of meats free of bones,
sinew and skin.
• The grating attachment can be used for chopping, peeling, grating
and slicing practically all types of fruits and vegetables. The grating
attachments are used for the processing of fruit, vegetables, cheese
and similar types of food.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
BEFORE FIRST USE
• Before first use, wash all parts that come into contact with food in hot
water using neutral dishwashing detergent. Then rinse these parts
with clean water and allow them to dry naturally or dry them out their
using awiping cloth.
Attention:
No part of this appliance is designed to be washed in
adishwasher!
When cleaning the cross blade and the graters, be
very careful not to injure yourself on their sharp parts.
• Clean the motor base unit using only adampened cloth. At the same
time, ensure that water does not enter into the base unit, especially
into the control switches.
• Clean the grinder or grater attachment mounting hole only using adry
wiping cloth.
• Only clean the power cord of the motor base unit using adry wiping
cloth.
Warning:
Never rinse the motor base unit or its power cord
under water or submerge it in water.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USING THE MEAT GRINDER
ASSEMBLING THE GRINDER for grinding meat
(Fig. E)
• One by one, gradually insert the screw shaft, cross blade and the
grinding disc into the grinding chamber, based on the preferred
grinding fineness. Finally, screw the screw ring on to the grinding
chamber and tighten it firmly.
Attention:
When attaching the cross blade, be very careful not
to injure yourself on its sharp cutting edges.
ASSEMBLING THE GRINDER for sausage making
(Fig. F)
• One by one, gradually insert the screw shaft, shaper and the sausage
stuffer attachment. Finally, screw the screw ring on to the grinding
chamber and tighten it firmly.
ASSEMBLING THE GRINDER for making kebbe
(Fig. G)
• One by one, gradually insert the screw shaft, shaper and the separator
attachment. Finally, screw the screw ring on to the grinding chamber
and tighten it firmly.
LOCATION OF THE MOTOR BASE UNIT
• Place the motor base unit on an even, dry, clean and especially stable
surface, for example on akitchen countertop. Insert the motor base
unit power cord into apower socket.
Attention:
Always locate the motor base unit in such away that
nobody can brush against it and thereby pull or push
it over. Never locate it on the edge of the countertop or
table, the vibrations during use may cause it to move
resulting in asubsequent fall.
MOUNTING THE GRINDER ON THE BASE UNIT
(Fig. H)
• Press and hold down the lock/release button A1 on the motor base
unit.
• Tilt the assembled grinder to the right at an angle of approximately
45°, push it against the hole on the base unit and turn it anticlockwise
to set it into the operating position.
• Release the grinder lock/release button.
• Insert the feeder tray into the feed tube.
EN Meat grinder
User'smanual

- 5 - 10/2022
2022, .
GRINDING
• Before grinding, remove any bones, cartilage and tendons from the
meat. Cut the meat into pieces measuring approximately 20 x 20 x
40 mm.
• Cut fruit and vegetables into pieces that will freely pass through the
feed tube.
Attention:
Never attempt to grind frozen meat or other types
of frozen food. It is necessary to allow frozen food to
defrost completely before grinding it.
• Underneath the grinder, place an appropriate bowl into which the
ground food will fall.
• Place the food that you wish to grind on to the feeder tray.
• Start the motor base unit by pressing the ON/OFF button.
• Gradually place the food into the feed tube, and using the pusher,
push it down into the grinding chamber. To prevent the grinder from
clogging, do not overfill the feed tube. Push down gently on the
pusher.
Warning:
Never use fingers or other items to push the
ingredients in. For this, always use the provided
pusher.
• In the event that the feed tube becomes clogged, first turn off the
grinder using the ON/OFF button and attempt to release it using
reverse rotation (see chapter REVERSE ROTATION). If reverse rotation
does not release the grinder, disconnect it from the power socket, take
the grinder off the base unit and clean it out. If necessary, completely
disassemble the grinder, clean it out and reassemble it. Mount it back
on to the motor base unit and continue working.
Attention:
The maximum continuous operating time of the
appliance is 5 minutes. Then allow it to cool down for
approximately 10 minutes.
• When you have finished using it, stop the base unit using the ON/
OFF button and disconnect the power cord from the power socket.
Ensure that the rotating parts have stopped rotating, take the grinder
off the base unit (see REMOVING THE GRINDER FROM THE BASE
UNIT) and disassemble it into its individual parts. Then clean all
used parts according to the instructions in chapter CLEANING AND
MAINTENANCE.
REVERSE ROTATION
• In the event that the grinder behaves in an unusual manner (e.g. it
is noisier or vibrating, the grinding chamber is clogged), turn it off by
pressing the ON/OFF button. Then press the REV button (reverse
rotation).
• The screw shaft will start rotating in reverse direction and the grinding
chamber will start emptying itself.
• If this does not happen, disconnect the base unit from the power
socket, completely disassemble the grinder, clean it out and
reassemble it. Mount it back on to the motor base unit and continue
working.
MAKING SAUSAGES OR KEBBE
• Prepare aground meat mixture and acasing for stuffing. Place the
casing into lukewarm water for 10 minutes before filling it. Slide the
wet casing on to the attachment. Leave afew free centimetres at the
end of the casing and then tie it or skewer it.
• Insert the feeder tray into the feed tube.
• Start the motor base unit by pressing the ON/OFF button.
• Put the meat mixture on to the feeder tray, and using the pusher,
push it down into the grinding chamber. To prevent the grinder from
clogging, do not overfill the feed tube. Push down gently on the
pusher.
Warning:
Never use fingers or other items to push the
ingredients in. For this, always use the provided
pusher.
• When making Kebbe, the grinder will extrude hollow tubes that you
can cut to the required length.
• In the event that the feed tube becomes clogged, first turn off the
grinder using the ON/OFF button and attempt to release it using
reverse rotation (see chapter REVERSE ROTATION). If reverse rotation
does not release the grinder, disconnect it from the power socket, take
the grinder off the base unit and clean it out. If necessary, completely
disassemble the grinder, clean it out and reassemble it. Mount it back
on to the motor base unit and continue working.
Attention:
The maximum continuous operating time of the
appliance is 5 minutes. Then allow it to cool down for
approximately 10 minutes.
• When you have finished using it, stop the base unit using the ON/
OFF button and disconnect the power cord from the power socket.
Ensure that the rotating parts have stopped rotating, take the grinder
off the base unit (see REMOVING THE GRINDER FROM THE BASE
UNIT) and disassemble it into its individual parts. Then clean all
used parts according to the instructions in chapter CLEANING AND
MAINTENANCE.
REMOVING THE GRINDER FROM THE BASE UNIT
• Press and hold down the lock/release button A1 on the motor base
unit.
• Turn the grinder clockwise (to the right) to an angle of approximately
45° and slide it off the hole of the base unit.
• Release the lock/release button.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
USING AGRATING ATTACHMENT
ASSEMBLY
(Fig. D)
• Depending the preferred grating fineness, select agrater and insert it
into the grating chamber of the attachment. Turn the grater clockwise
to lock it in the chamber.
Attention:
When handling the graters, be very careful not to
injure yourself on their sharp parts
MOUNTING THE GRATING ATTATCHMENT TO THE BASE UNIT
(Fig. I)
• Press and hold down the lock/release button A1 on the motor base
unit.
• Tilt the attachment to the right at an angle of approximately 45°, push
it against the hole on the base unit and turn it anticlockwise to set it
into the operating position.
• Release the lock/release button.
GRATING
• Place an appropriate container, into which the grated food will fall,
underneath the outlet of the attachment.
• Cut the food into pieces that are suitable for insertion into the feed tube
of the attachment.
• Start the motor base unit by pressing the ON/OFF button.
• Gradually place the food into the feed tube, and using the pusher,
push it down into the chamber. To prevent the grater from clogging, do
not overfill the feed tube. Push down gently on the pusher.

- 6 - 10/2022
2022, .
Warning:
Never use fingers or other items to push the
ingredients in. For this, always use the provided
pusher.
• When you have finished using it, stop the base unit using the ON/
OFF button and disconnect the power cord from the power socket.
Ensure that the rotating parts have stopped rotating, take the
grater attachment off the base unit (see REMOVING THE GRATER
ATTACHMENT FROM THE BASE UNIT) and disassemble it into its
individual parts. Then clean all used parts according to the instructions
in chapter CLEANING AND MAINTENANCE.
REMOVING THE GRATING ATTACHMENT FROM THE BASE UNIT
• Press and hold down the lock/release button A1 on the motor base
unit.
• Turn the attachment clockwise (to the right) to an angle of
approximately 45° and slide it off the hole of the base unit.
• Release the lock/release button.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CLEANING AND MAINTENANCE
Warning:
Prior to any cleaning or maintenance, always turn
off the appliance, disconnect it from the power
socket and disassemble it into its individual parts.
Never clean any part when the grinder or agrating
attachment is mounted on the base unit and the base
unit is connected to apower socket.
Never use chemicals, dishwashing abrasive wool,
steel wool or cleaning products with abrasive
components for cleaning. Otherwise the surface of
the parts may be damaged.
Note:
Remains of unground meat may remain in the grinding
chamber that are hard to clean away. To make their
removal easier, you can grind apiece of bread or bread roll.
We recommend disassembling the grinding attachment in
akitchen sink or alarger bowl to prevent potentially soiling
the work surface.
If the grinder or the grating attachment is used for an
extended period of time, it is possible that the base unit may
be hot to touch. Allow it to cool down before cleaning it.
• We recommend cleaning all the parts as soon as possible after use,
before the food scraps dry on. These are harder to remove later.
• Disassemble the grinder or the grating attachment into its individual
parts. Clean the all the removed parts from food remains, wash in
warm water with dish washing detergent and rinse under clean
running water. Then allow them to dry naturally or dry them out
thoroughly using awiping cloth. Do not use abrasive cleaning
products.
Attention:
No part of this appliance is designed to be washed in
adishwasher!
When cleaning the cross blade and the graters, be
very careful not to injure yourself on their sharp parts.
• Clean the motor base unit using only adampened cloth. At the same
time, ensure that water does not enter into the base unit, especially
into the on/off and reverse rotation switches.
• Clean the grinder or grater attachment mounting hole only using adry
wiping cloth.
• Only clean the power cord of the motor base unit using adry wiping
cloth.
Warning:
Never rinse the motor base unit or its power cord
under water or submerge it in water.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STORAGE
• When you have finished using the appliance and its parts, store
these in aclean, dry place out of children'sreach. Keep the stored
appliance and its parts away from extreme temperatures, direct
sunlight and excessive humidity and do not store these in an overly
dusty environment.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECHNICAL SPECIFICATIONS
Rated voltage range ..................................................................................220-240 V
Rated frequency...........................................................................................50-60 Hz
Rated power input..............................................................................................500 W
Max. input........................................................................................................... 1400 W
Capacity .......................................................................................................... 1.7 kg/min
Weight (approximate)..........................................................................................3.4 kg
Electrical shock protection class............................................................................... II
Noise level .......................................................................................................90 dB(A)
The declared noise emission level of the appliance is 90 dB(A), which
represents alevel Aof acoustic power with respect to areference acoustic
power of 1 pW.
Explanation of technical terminology
Safety class for electrical shock protection:
Class II – Electrical shock protection is provided by double or
heavy-duty insulation.
Changes to text and technical parameters are reserved.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUCTIONS AND INFORMATION REGARDING THE DISPOSAL OF
USED PACKAGING MATERIALS
Dispose of used packaging material at asite designated for waste in your
municipality.
DISPOSAL OF USED ELECTRICAL AND ELECTRONIC EQUIPMENT
This symbol on products or original documents means that
used electric or electronic products must not be added to
ordinary municipal waste. For proper disposal, renewal and
recycling, hand these appliances over to determined
collection points. Alternatively, in some European Union
states or other European countries you may return your
appliances to the local retailer when buying an equivalent
new appliance. Correct disposal of this product helps save
valuable natural resources and prevents potential negative effects on the
environment and human health, which could result from improper waste
disposal. Ask your local authorities or collection facility for more details. In
accordance with national regulations penalties may be imposed for the
incorrect disposal of this type of waste.
For business entities in European Union states
If you want to dispose of electrical or electronic equipment, ask your
retailer or supplier for the necessary information.
Disposal in other countries outside the European Union.
This symbol is valid in the European Union. If you wish to dispose of this
product, request the necessary information about the correct disposal
method from the local council or from your retailer.
This product meets all the basic requirements of EU
directives related to it.

FAST ČR, a.s.
U Sanitasu 1621
CZ-251 01 Říčany
www.sencor.eu