Detech GATE WL User manual

DeTech 1GateWL REV: 02/08/2018
GATE WL
Double tented technology via
bidirectional radio
Gate WL is a double tented technology sensor, with a 140° x
15° coverage. Ideal for the protection of gaps, doors,
windows, corridors and balconies.
Caratteristiche tecniche
➢Absorption at rest: 26 uA.
➢Installation height: up to 4 m.
➢Adjustable range.
➢Adjustable relevation sensibility.
➢Microstrip microwave 10.525 gHz.
➢Flicker-free board
➢Sealed optical.
➢140° x 15° for 4 m coverage
➢Power supply: 3,6v- n.1 lithium battery ,3v6 mod. ER14505
cabled AA 2,4Ah.
➢3 years of life (at standard use)
➢Radio Freq.868MHz-FM.
➢Encrypted code.
➢Anti tampering protection.
➢Radio supervision.
➢Visual indication of low battery
➢Selectable detection circuit.
! WARNING: Before every trial, connect the
sensor to the receiver
1. Installation guide
Gate WL è is designed to protect gaps like corridors,
windows and balconies. It has to be placed horizontally in
the middle and on the highest area of the place you need
protection on.
Remove the upper lid, remove the board pushing on the finger,
carve the preprinted holes on the bottom and secure it with the
screws and the pieces to protect with the lens pointing
downwards. Do not point the sensor upwards. Its coverage in
width is twice its installation height.. Ex: if placed in the middle
of a window 1m tall, its coverage in width will 2 m.
2.BATTERY INSERTION Remove the board and connect the
battery to the circuit through the connector, positioned on the
back of the board and put it in the battery carrier on the D
bottom. Wait 2 minutes for the auto-calibration. The GREEN and
RED LEDs will blink alternatively
3. ACQUISITION The acquisition of the sensor in the system
takes place when a Tamper alarm is generated (by releasing the
Tamper button) or setting the battery in “acquisition” mode.
4RADIO COVERAGE TEST When the battery is disconnected,
push the Tamper button and connectthe battery. When the LED
will blink, drop the Tamper button. The GREEN LED suggests a
good signaling, when the GREEN and RED LEDs blink, the wireless
signal is not fit, with no blinking the signal is absent. To end the
Test, push the Tamper or wait for 4 minutes.
5. ADJUSTMENT
Adjust the range of the microwave through the dedicated
trimmer. Select, if necessary, the high sensitivity relevation
mode for open gaps that can be crossed on the run ( sens jumper
inserted) To disable, if requested, the LED display,insert the LED
jumper. Close the lid, hooking it on the battery side, and closing
it with a screw. Once the lid is closed, the TAMPER will activate;
The validation of the correct closure of the tamper is given by an
alternating blinking (lasting for a couple of seconds) of the
GREEN and RED LEDs. Repeat this operation if necessary.
! WARNING: Before every trial, connect the
sensor to the receiver
6. WALK TEST
Antenna
Finger
Tamper
Trimmer regulation MW

DeTech 2GateWL REV: 02/08/2018
Once the lid is closed, the sensor will prepare for 3 minutes at the
coverage test. Move towards the space you need protection and
verify the coverage through the microwave green led and the
infrared red led (the display is delayed 2 sec). The ending of the test
will be signaled by the green led. If needed, increase or dicrease the
range of the microwave. Once the test time is over, the sensor will
send out a signal with a green led and will prepare for a correct
functioning. To start a new self test, open and close the lid.
Premise: when functioning, at the detection of an alarm, the
sensor is inhibited for 2 sec. If the SET line of the GateWL Rev D is
connected, the sensor won’t be inhibited, once the system is
inserted
7. MEMORIA ALLARME
When the alarm is switched off, the sensor will report an eventual
alarm through the GREEN and RED LED. The memory will be erased
at the moment of the next insertion. Active with LED OFF also.
8. BATTERY SIGNALING The low battery status is signaled through
the blinking of the RED LED. In LED OFF also.
9. BATTERY REPLACEMENT To replace the battery, set the system
in MAINTENANCE mode, open the sensor, remove the battery,
insert a new battery and close the lid.
10. WARNING:
•explosion danger if the battery isn’t replaced correctly.
Replace it only with an equal or equivalent type.
•In case the battery shows leakage of liquid, change it
immediately. Afterwards, clean your hands if you touched
the fluid.
Warning: Because of its small dimensions, the product can be
ingested easily. Keep away from children.
11 INFORMATION RELATING TO THE DISPOSAL (RAEE GUIDELINE)
•Warning: don’t throw this product in the normal trash bin!
•The electrical and electronical equipment must be managed
separately in accordante with the legislation requiasting the
management, the disposal and recycling of such products
DISPOSAL OF THE BATTERY:
Warning: the battery contains polluting substances, therefore it
must be put in special predisposed to the collecting and disposal of
polluting waste.
The correct disposal of this product will contribute to the right
treatment, recovery and disposal, preventing an eventual negative
impact on the environment and on human health. Penalties may be
imposed in case of non compliance of the 151/05 Legislative
Decree.
WARRANTY
This product is ensured for 5 years (upon
the occurrence of malfunctioning or
manufacturing faults).
RED directive, rule EN 60950-1, EN 50130-4, EN 50130-5
EN61000-6-3, EN 300 440,
EN301489-3 e EN 62479
DECLARATION OF CONFORMITY
EU
DeTech declares that the product is in accordance with the 2014/53/UE
directive. The EU declaration of conformity is available on the following site
www.DeTechsrl.it
DATA
Power supply
3,6V cc +/-30%
Max absorption
30 uA
Microwave
Strip 10.525 GHz 8 dBm
Alarm length
3 sec.
RFI immunity
0,1/500 MHZ 3V/m
Working
temperature
-5°C/+55°C
Radio Freq
868 FM bidirezionale
Humidity
95%
Clarification
AT
BE
BG
CY
HR
DK
EE
FI
FR
DE
EL
IE
IT
LV
LT
LU
MT
NL
PL
PT
GB
CZ
RO
SK
SI
ES
SE
HU