DeView MD4-PWM Assembly instructions

Step 1
Step 3
Prepare 4 holes for anchor location.
Step 2
Install the wall mount
Mounting Surface
Precautions
To prevent damage to your dome camera or injury to
yourself or to others, please read and comply with the safety
precautions in the enclosure installation and
camera sheet before installation and use.
Product Overview Installation Quick Overview
Package Kit
Dimensions
About Copper sleeves
Copper Sleeves
Screw
Hole
Mounting Surface
Mounting Surface
Screw
Explosion View
The cooper sleeves create the required space which allows the
mount to be installed using the four mounting holes
Sectional View
Install the dome
The following illustrates how to install copper sleeves. For more information,
please see “2. Installing Wall Mount” overleaf.
Wall Plug
Material
: 4.96 inch (126.00mm)Size
Unit Weight
0.278 lbs (126g)
Polycarbonate
H : 3.02inch (76.70mm)
Shipping Weight (per piece)
0.147 lbs (66.7g)
Wall Mount x 1
Copper Sleeves x 2
Self-tapping Screws x 3
Wall Plugs x 4
Screws x 4
133mm/ 5.24 inch
126.0mm/ 4.96 inch
76.7mm/
3.02 imch
29.5mm/
1.16 imch
14.4mm/
0.57 inch
33.4mm/
1.31 inch
40.7mm/
1.60 imch
Front View
Rear View
Side View
V531-JWA00-200
Ver.: 03/2010
50.8mm/
2.00 inch
MD4-PWM Pendant Wall Mount Cap
Installation Sheet
Please visit our website for more information
www.deview.com
Product specifications subject to change without notice.
Certain product names mentioned herein may by trade names
and/or registered trademarks of other companies.

Slide copper sleeves on screws and fasten into mounting holes (a and b).
2.1
Slide the mount over the copper sleeves (a and B)
and push down so mount is seated properly.
2.2
Secure the mount by fastening the
bottom two screws (c and d).
2.3
Dome Base
Self Tapping Screws
Camera Liner
Dome Cover
Video Connector
Power Connector
Mounting Pillar
Create 4 holes as anchor points a-d (install 4 wall plugs if appropriate
for surface type) and one cable entry e.
Prepare the mounting surface with the template provided below.
Template
2.1
ab
cd
Copper Sleeves
Screws
40.1mm
ab
cd
e
31.9mm
1. Preparing Mounting Surface
Mounting Pillar
Rotate
Tilt
Tamper Proof Screw
2.2
2.3
cd
3.5
Adjust the camera position and test
Adjust the camera position and test
Adjust the camera to the required position
and test. See detailed instructions in the enclosure
and camera installation sheets
3.6
Install the camera liner and cover
Install the camera liner and cover
Carefully fit the camera liner on the camera module.
Install and secure the dome cover and secure with
the supplied tamper screw.
2. Installing Wall Mount
The following describes the methods to install the camera on the wall mount.
Please kindly refer to the left illustration when you read through the
installation instructions.
3.1
Remove the dome cover and camera liner
Remove the dome cover and camera liner
3.2
Open the base mounting holes
Open the base mounting holes
Carefully open the three base mounting holes
(used for securing the enclosure to the mount)
3.3
Connecting the cables
Connecting the cables
Connect the video and power cable, Limit your
cable length that is coming into mount to 6".
Arrange the cables inside the mount.
3.4
Fit the dome base onto the mount
Fit the dome base onto the mount
Place the dome base onto the three mounting
pillars within the mount. Insert and tighten
the three mounting screws.
3. Installing Camera on Mount
3.1
3.2
3.3
3.4
3.5
3.6
4.4mm