Hills 80154973 User manual

Ames Australasia Pty Ltd
ABN 89 169 427 061
Level 1, 660 Doncaster Road,
Doncaster Vic 3108 Australia
Operating your Laundry Basket
Holder
Folding away after use
If you would like to gain back your space after the washing has been put out, simply raise the
Hills Laundry Basket Holder upwards until it rests in the 90-degree position.
Securing a Peg Basket
Attach the optional O-Ring provided to your existing peg basket. We recommend attaching this
anywhere towards the opening of your peg basket to allow you to easily reach inside.
Once the O-Ring is attached to your peg basket, loop the ring onto the hook located on the
corner of the front bar of your Hills Laundry Basket Holder. This will comfortably hold up to 2kg
of weight.
Laundry Basket Holder
Product Manual
80154973
Hills Contacts
We are committed to providing you with complete customer satisfaction. If you have any
questions or comments about our products or services please contact your nearest Customer
Service Centre during their local business hours:
Australia
1300 327 293
New Zealand
0800 021 027
Email
[email protected]
Hills Websites
Hills Home Living
hillshome.com.au
Hills Consumer Advice
hillshome.com.au/need-help

3
Introduction
Congratulations!
Congratulations on the purchase of your
new Hills Laundry Basket Holder.
Your Hills Laundry Basket Holder can be
either Wall-Mounted or Pole-Mounted.
It’s important that you read this owner’s
manual thoroughly before installation to
benet from the design features and enjoy
safe use of this product.
Thank you for choosing Hills.
Warning
• Do not allow children or pets to climb or
swing on the Laundry Basket Holder.
• Do not use for any purpose other than to
hold a laundry basket.
• Do not use this Laundry Basket Holder if
parts are worn or damaged.
• Always keep your laundry basket placed in
the centre of the Laundry Basket Holder to
prevent risk of toppling.
2 x Steel Arms
2 x Chicago Bolts
1 x O-Ring Attachment
61
1 x Front Bar
2 x Large Hex Keys
1 x Small Hex Key
2 x Arm End Caps
Carton Contents
2 x Large M8x50
Bolt and Nuts
Fig. 9 Fig. 10
Fig. 11
Attaching the Arms to the Wall Bracket
2.3 Slide 1 x Arm End Cap onto 1 x Steel Arm. Refer to Fig. 9. Secure the Arm to the outside
of the Wall Bracket using 1 x Large M8x50 Bolt and 1 x Large Hex Key.
Note: When installing, ensure that the flat side of the rubber sleeve is facing upwards.
Repeat this process on both sides of the Wall Bracket. Refer to Fig. 10.
2.4 Attach the Front Bar onto the Arms as shown below in Fig. 11. If required, gently tap the
Front Bar into the Arms.
2.5 Secure the Front Bar onto the Arms using the 2x Chicago Bolts and 2 x Large Hex Keys
provided.

5 225
Wall-Mounted Installation
Attaching the Wall Bracket to your wall
2.0 Place 2 x Large M8 Nuts into the designated hex shape holes on the inside of the
Wall Bracket. Ensure the Nuts are inserted as per Fig. 7 with the coloured rings
facing one another. Important: 2 x M8x70 masonry wall bolts are supplied with
this product for mounting to masonry, brick, or concrete walls. If mounting to a
different substrate such as wood or other specialised materials, please consult
your local hardware store for advice on which xings to use.
2.1 Using the Wall Bracket as a template, mark the hole centres onto your wall. The
distance between these markings should be 62mm. Use a spirit level to ensure
the hole centres are level vertically. Refer to Fig 8.
Note: We recommend the upper hole is in line with the user’s waist. Ensure that
there is adequate space for the Laundry Basket Holder to be folded into the up
position before drilling holes.
2.2 If you are mounting to masonry, brick or concrete, drill 10mm holes at the marked
points and secure the wall bracket into position using the M8x70 masonry
wall bolts supplied. If using alternative xings, secure the wall brackets in an
appropriate manner for your substrate.
Installation Options
Components for Pole-Mounting only
1 x LH Pole Bracket 1 x RH Pole Bracket 2 x Small M6x20 Bolt
and Nuts
1 x Wall Bracket 2 x M8x70 Wall Fixings
Components for Wall-Mounting only
The Hills Laundry Basket Holder can be Pole-Mounted onto most rotary/ground mounted
clotheslines, or Wall-Mounted on masonry, brick or concrete walls.
Please ensure you follow the correct instructions below for your desired installation location.
For Pole-mounted Installation, please turn to Page 3.
For Wall-mounted Installation, please turn to Page 5.
62mm
Fig. 7 Fig. 8

73
Pole-Mounted Installation
Attaching the Pole Bracket to your clothesline
1.0 Place 2 x Large M8 Nuts into the designated hex shape holes on the inside of the LH
and RH Pole Brackets. Ensure the Nuts are inserted as per Fig. 1 with the coloured ring
visible.
1.1 Place the LH and RH Pole Brackets onto the main pole of your clothesline. Ensure the
arrow on the inside of each bracket is pointing upwards.
1.2 Insert 1 x Small M6 Nut into the designated hex shape hole on the outside of the LH
Pole Bracket. Make sure the coloured ring on the nut is facing outwards. Slide the Small
M6 Bolt through the RH Pole Bracket, and lightly tighten using the Small Hex Key so it
is secure but not fully tightened. Repeat this process for the second hole before fully
tightening both. Refer to Fig. 2.
Note: We recommend installing no lower than 10cm below the winding handle casing.
Refer to Fig. 3.
4
Attaching the Arms to the Pole Bracket
1.3 Slide 1 x Arm End Cap onto 1 x Steel Arm. Refer to Fig. 4. Secure the Arm to the outside
of the Pole Bracket using 1 x Large M8x50 Bolt and 1 x Large Hex Key. Refer to Fig. 5.
Note: When installing, ensure that the flat side of the rubber sleeve is facing upwards
before securing. Repeat this process on both sides of the pole bracket.
1.4 Attach the Front Bar onto the Arms as shown below in Fig. 6. If required, gently tap the
Front Bar into the Arms.
1.5 Secure the Front Bar onto the Arms using the 2 x Chicago Bolts and 2 x Large Hex Keys.
Fig. 2 Fig. 5
Fig. 3
Fig. 1 Fig. 4
Fig. 6
10cm