DFK HardCabs CAN-AM COMMANDER 1000 LIMITED User manual
.
INSTALLATION INSTRUCTIONS
CAN-AM
COMMANDER 1000 LIMITED
CAN-AM
COMMANDER 1000 LIMITED
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
2
SAFETY INSTRUCTIONS
Warning: Failure to heed all safety and operating instructions and
warnings regarding use of this product can result in serious bodily injury.
READ PROPERLY COMPLETE ASSEMBLY INSTRUCTIONS BEFORE
STARTING OF ASSEMBLY
Install all parts indicated in assembly instructions. Failure to fully assemble
product before use could result in personal injury.
Assembly of product requires use of hand or power tools.
If you are not experienced in using these types of tools,
have product dealer do the install for you.
Some parts contain sharp edges, wear protective gloves if necessary.
Always keep your assembly area clean, uncluttered and well lit.
Keep visitors and children a safe distance away from the assembly area. Visitors
should wear the same safety equipment described under.
Never operate your UTV with the cab doors open. Failure to properly latch the
doors before moving the vehicle could result in serious injury.
Dress for safety. DO NOT wear loose clothing, gloves, neckties or jewelry if
using power tools to assemble this product.
Insert all nut covers after you finish installation.
Never drive your UTV with the cab front window in open position.
Failure of improperly latching/locking the front window before driving
the vehicle could result in serious injury.
CAN-AM
COMMANDER 1000 LIMITED
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
3
MAINTENANCE AND CLEANING
To clean polycarbonate surface use soapy water solution or other subtle means.
Dirt and dust wash by gently water stream and swipe only with wet or damp
means in the direction from top to bottom.
The recommended frequency of cleaning of polycarbonate part
is about 1 time per month or according to the actual degree of pollution.
Do not use detergents that could scratch the surface plates.
(abrasives, harsh fabrics, etc.)
Do not use solvents or alkaline detergents or cleaners with ammonia
(ammonium hydroxide).
Do not remove the impurities from the surface of the razor blades or other sharp
items.
Do not clean cabin when the polycarbonate plates are heated by the sun.
Do not use the squeegee, it could be scratched surface plates.
Do not clean the water current strength greater than 50 bar (WAP)
The manufacturer is not responsible for scratching the surface in case of failure to
comply with the above instructions.
All bolted connections of cab must be by user at regular intervals checked and
tightened.
CAN-AM
COMMANDER 1000 LIMITED
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
4
TOOLS NEEDED
Not included
Ratchet handle
Socket beg 19 mm
Socket beg 13 mm
(0,75 in)
(0,51 in)
Socket beg 10 mm
Socket beg 8 mm
Metric wrench 19 mm,
13mm and 10mm
(0,39 in)
(0,31 in)
Screwdriver philips
Screwdriver straight
Hex key 5, 6 and 8 mm
CAN-AM
COMMANDER 1000 LIMITED
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
6
PREPARATION FOR INSTALLATION:
Uninstall all additional systems from the roller cage (work lights, rear mirrors, drink holders etc.)
Uninstall all parts and assemblies of the original cab.
If you think, you need use our cab (probably in summer) without the doors, you can insert the side safety
nets under the seats. Uninstall the side safety net’s upper screws (in red circles) and pull down the nets.
Save the safety net’s screw carefully, you need these later.
CAN-AM
COMMANDER 1000 LIMITED
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
13
Fix the door base holder with the door base to the roller cage by nut, washer and nut cover.
Tighten nut gently and repeat previous steps with right door base and holders.
CAN-AM
COMMANDER 1000 LIMITED
HardCabs 630-324-8585 www.hardcabs.com
2464 Wisconsin Ave.
Downers Grove, IL 60515 info@hardcabs.com
20
Fix the side ledge with seal with the door base to the roller cage by nuts, washers and nut covers.
Tighten nuts gently and repeat previous steps with the right door base and side ledge.
Table of contents
Other DFK Offroad Vehicle manuals
