Digimerge Dnb14tl2 User manual

www.digimerge.com

Instruction Manual

English Version 2.0

DNB14TL2

IR Bullet IP Camera

Thank you for purchasing this product. Digimerge is committed to providing our

customers with a high quality, reliable security solution.

This manual refers to the following models:

• DNB14TL2

For more information on this product, firmware updates, and accessory products,

please visit us at:

www.digimerge.com

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT

REMOVE COVER. NO USER SERVICABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an

equilateral triangle, is intended to alert the user to the

presence of uninsulated "dangerous voltage" within the

product's enclosure that may be of sufficient magnitude to

constitute a risk of electric shock.

The exclamation point within an equilateral triangle is

intended to alert the user to the presence of important

operating and maintenance (servicing) instructions in the

literature accompanying the appliance.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS UNIT TO RAIN OR MOISTURE.

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE

OF THE PLUG TO THE WIDE SLOT AND FULLY INSERT.

Important Safeguards

In addition to the careful attention devoted to quality standards in the manufacturing process of

your video product, safety is a major factor in the design of every instrument. However, safety is

your responsibility too. This sheet lists important information that will help to assure your

enjoyment and proper use of the video product and accessory equipment. Please read them

carefully before operating and using your video product.

Installation

1. Read and Follow Instructions - All the safety and

operating instructions should be read before the

video product is operated. Follow all operating

instructions.

2. Retain Instructions - The safety and operating

instructions should be retained for future reference.

3. Heed Warnings - Comply with all warnings on the

video product and in the operating instructions.

4. Polarization - Do not defeat the

safety purpose of the polarized or

grounding-type plug.

A polarized plug has two blades

with one wider than the other.

A grounding type plug has two

blades and a third grounding prong.

The wide blade or the third prong

are provided for your safety.

If the provided plug does not fit into your outlet,

consult an electrician for replacement of the

obsolete outlet.

5. Power Sources - This video product should be

operated only from the type of power source

indicated on the marking label. If you are not sure of

the type of power supply to your location, consult

your video dealer or local power company. For video

products intended to operate from battery power, or

other sources, refer to the operating instructions.

6. Overloading - Do not overload wall outlets of

extension cords as this can result in the risk of fire

or electric shock. Overloaded AC outlets, extension

cords, frayed power cords, damaged or cracked wire

insulation, and broken plugs are dangerous. They

may result in a shock or fire hazard. Periodically

examine the cord, and if its appearance indicates

damage or deteriorated insulation, have it replaced

by your service technician.

7. Power Cord Protection - Power supply cords should

be routed so that they are not likely to be walked on

or pinched by items placed upon or against them,

paying particular attention to cords at plugs,

convenience receptacles, and the point where they

exit from the video product.

8. Ventilation - Slots and openings in the case are

provided for ventilation to ensure reliable operation

of the video product and to protect it from

overheating. These openings must not be blocked or

covered. The openings should never be blocked by

placing the video equipment on a bed, sofa, rug, or

other similar surface. This video product should

never be placed near or over a radiator or heat

built-in installation such as a bookcase or rack

unless proper ventilation is provided or the video

product manufacturer’s instructions have been

followed.

9. Attachments - Do not use attachments unless

recommended by the video product manufacturer as

they may cause a hazard.

10. Camera Extension Cables – Check the rating of

your extension cable(s) to verify compliance with

your local authority regulations prior to installation.

11. Water and Moisture - Do not use this video product

near water. For example, near a bath tub, wash

bowl, kitchen sink or laundry tub, in a wet

basement, near a swimming pool and the like.

Caution

: Maintain electrical safety. Powerline

operated equipment or accessories connected to

this unit should bear the UL listing mark of CSA

certification mark on the accessory itself and should

not be modified so as to defeat the safety features.

This will help avoid any potential hazard from

electrical shock or fire. If in doubt, contact qualified

service personnel.

12. Accessories - Do not place this

video equipment on an unstable

cart, stand, tripod, or table. The

video equipment may fall, causing

serious damage to the video

product. Use this video product

only with a cart, stand, tripod,

bracket, or table recommended by the

manufacturer or sold with the video product. Any

mounting of the product should follow the

manufacturer’s instructions and use a mounting

accessory recommended by the manufacturer.

General Precautions

Service

13. Servicing - Do not attempt to service this video

equipment yourself as opening or removing covers

may expose you to dangerous voltage or other

hazards. Refer all servicing to qualified service

personnel.

14. Conditions Requiring Service - Unplug this video

product from the wall outlet and refer servicing to

qualified service personnel under the following

conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled or objects have fallen into

the video product.

• If the video product has been exposed to rain or

water.

• If the video product does not operate normally by

following the operating instructions. Adjust only

those controls that are covered by the operating

instructions.Improper adjustmentofother controls

may result in damage and will often require

extensive work by a qualified technician to restore

the video product to its normal operation.

• If the video product has been dropped or the cabinet

has been damaged.

• When the video product exhibits a distinct change

in performance. This indicates a need for service.

15. Replacement Parts - When replacement parts are

required, have the service technician verify that the

replacements used have the same safety

characteristics as the original parts. Use of

replacements specified by the video product

manufacturer can prevent fire, electric shock or

other hazards.

16. Safety Check - Upon completion of any service or

repairs to this video product, ask the service

technician to perform safety checks recommended

by the manufacturer to determine that the video

product is in safe operating condition.

17. Wall or Ceiling Mounting - The cameras provided

should be mounted to a wall or ceiling only as

instructed in this guide, using the provided

mounting brackets.

18. Heat - The product should be situated away from

heat sources such as radiators, heat registers,

stoves, or other products (including amplifiers) that

produce heat.

Use

19. Cleaning - Unplug the video product from the wall

outlet before cleaning. Do not use liquid cleaners or

aerosol cleaners. Use a damp cloth for cleaning.

20. Product and Cart Combination - Video and cart

combination should be moved with care. Quick

stops, excessive force, and uneven surfaces may

cause the video product and cart combination to

overturn.

21. Object and Liquid Entry - Never push objects of any

kind into this video product through openings as

they may touch dangerous voltage points or

“short-out” parts that could result in a fire or

electric shock. Never spill liquid of any kind on the

video product.

22. Lightning - For added protection for this video

product during a lightning storm, or when it is left

unattended and unused for long periods of time,

unplug it from the wall outlet and disconnect the

antenna or cable system. This will prevent damage

to the video product due to lightning and power line

surges.

iii

General Precautions

1. All warnings and instructions in this manual should be followed.

2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents. Use a

water dampened cloth for cleaning.

3. Keep enough space around the unit for ventilation. Slots and openings in the storage cabinet

should not be blocked.

4. During lightning storms, or when the unit is not used for a long time, disconnect the power

supply, antenna, and cables to protect the unit from electrical surge.

FCC CLASS A NOTICE

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used

in accordance with the manufacturer’s instruction manual, may cause harmful interference with

radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference, in which case you will be required to correct the interference at your own expense.

This equipment has been certified and found to comply with the limits regulated by FCC, EMC, and

LVD. Therefore, it is designated to provide reasonable protection against interference and will not

cause interference with other appliance usage.

However, it is imperative that the user follows the guidelines in this manual to avoid improper

usage which may result in damage to the unit, electrical shock and fire hazard injury.

In order to improve the feature functions and quality of this product, the specifications are subject

to change without notice from time to time.

www.digimerge.com

Features

• 2.1 MP HD, 1/2.5” CMOS Progressive Scan

• 1080p picture quality at real-time (30 fps)

• Triple-streaming (H.264/MJPEG)

• Futureproof ONVIF 2.1 compliance (1.02 backwards compatible)

• Compatible with popular third party VMS software*

• Milestone XProtect® GO (8 Channel) VMS included plus Digimerge

CMS-DH PRO and Syncro-V

• Power-over-Ethernet (PoE) operation, 14Watt max/12V operation

• Backup options: SD card, FTP, NAS, local

• Mobile Apps: iPhone®, iPad®, Android™

• Supports two-way audio

• 2.8-12mm Varifocal MegaPixel lens

• 120 ft (36 m) IR Night Vision, True Day/Night (TDN)

• IP66 Weatherproof rated

• Multi-browser support: IE, Firefox, Safari®, Chrome

• External Zoom/Focus Adjustment

• Free Digimerge DDNS service

• Cable through bracket design and easy installation with mounting plate

included

* See www.digimerge.com for the most updated list of third party VMS compatibility

TABLE OF CONTENTS

1. Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.1 Default Camera Username, Password, and Ports . . . . . . . . . . .1

1.2 Camera Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1.2.1 Functions of status LED’s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.3 Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

1.4 ONVIF Compatibility and Included Software Overview . . . . . . . .3

1.4.1 Milestone XProtect Go® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.4.2 Syncro-V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.4.3 CMS-DH PRO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2. Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

3. Camera Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

4. Finding the Camera’s IP Address . . . . . . . . . . . . . . . . . 10

4.1 Finding the Camera’s IP Address Using Syncro-V . . . . . . . . . .10

4.2 Finding the Camera’s IP Address using UPnP in Windows® 7 11

4.3 Finding the Camera’s IP Address using Bonjour® in Mac OS® 12

4.4 Finding the Camera IP using the BNC Test Cable . . . . . . . . . . .13

5. Configuring Remote Connection . . . . . . . . . . . . . . . . . . 14

5.1 Connecting to a DDNS address using Syncro-V . . . . . . . . . . . .18

6. Web Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

6.1 Supported Browsers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

6.2 Chrome, Firefox, and Safari Setup . . . . . . . . . . . . . . . . . . . . . . .20

6.3 Internet Explorer® Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

6.4 Web Interface/Live Video Overview . . . . . . . . . . . . . . . . . . . . . . .24

6.4.1 Live Video Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

6.4.2 Configuring Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

6.5 Device Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26

6.6 Stream Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27

6.7 Device Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28

6.7.1 Local Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.7.2 Device Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

6.7.3 Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.7.4 Date & Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.7.5 OSD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

6.7.6 Microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34

6.7.7 BNC Video Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

6.7.8 Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35

6.8 Alarm Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

6.8.1 Disk Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36

6.8.2 Motion Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

6.9 Local Record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

6.9.1 Record Directory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39

6.9.2 Record Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44

6.10 Privacy Masking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.11 Network Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

6.11.1 DDNS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47

6.12 Service Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

6.12.1 SMTP (Email Alert Setup) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

6.13 Privilege Manager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

6.13.1 Group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49

6.13.2 User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

6.13.3 Unlocking User Accounts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52

6.14 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

6.14.1 Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

6.15 Device Restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.16 Default Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

6.17 Sensor Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

6.17.1 Image Adjust . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

6.17.2 Shutter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55

6.17.3 Gain Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

6.17.4 Day/Night Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

6.17.5 Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

6.17.6 Gamma . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57

6.17.7 AE Meter Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

6.17.8 WDR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

6.17.9 WB Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59

6.17.10 Mirror . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

6.17.11 Noise Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

7. Resetting to Factory Defaults . . . . . . . . . . . . . . . . . . . 61

8. Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

9. Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . 63

10. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Getting Started

1. GETTING STARTED

The system comes with the following

components:

Allen Key

RJ45 Coupler

RCA-to-BNC

Test Cable

Mounting Screw Kit:

• 4 x mounting screws

(PA4.0 x 35)

• 4 x anchors

• 4 x allen screws

• 1 x hinge screw

(pre-attached)

Mounting

Plate

• 1 x Camera

• 1 x Mounting Screw Kit

• 1 x Mounting Plate

• 1 x Allen Key

• 1 x RJ45 Coupler

• 1 x RCA-to-BNC Test Cable

• 1 x Mounting Template

• 1 x Quick Start Guide

• 1 x Instruction Manual

• 1 x Software/Documentation CD

1.1 Default Camera Username,

Password, and Ports

Username: admin

Password: admin

Ports: 80 (HTTP), 30001 (Control/

Streaming), 8080 (RTMP), 554 (RTSP)

IP Address: DHCP Enabled by Default

(Router will automatically assign IP

address)

NOTE: Once you have completed the basic setup of the camera, it is

recommended to configure a static IP address. This will prevent the camera

IP address changing in the event of a power failure. For details, see “6.7.1

Local Network” on page 29.

Getting Started

1.2 Camera Overview

1.2.1 Functions of status LED’s

• POWER/NET (Orange): On when power is connected. Flashes when

network is connected.

• SD (Red): On when SD card is inserted.

1.3 Mounting Accessories

• For more information or accessory installation instructions, visit

www.digimerge.com

RCA analog output

SD card slot

(max. 64GB supported;

SanDisk™/Kingston™ brand

memory cards recommended)

Status LED’s Reset Button

Focus Zoom

Junction Box Mount - model # MNTV2XB

Getting Started

1.4 ONVIF Compatibility and Included Software Overview

This camera is ONVIF v2.1 compliant. It is designed for interoperability with

popular VMS’s and NVR’s*, with backwards compatibility to ONVIF v.1.02. For

more information on ONVIF, visit www.onvif.org

Milestone XProtect Go®, Digimerge Syncro-V, and Digimerge CMS-DH PRO

are provided. Milestone XProtect Go® provides a server solution that can

host multiple cameras on a centralized location for access by remote clients.

Syncro-V and CMS-DH PRO are client-only, meaning that each camera must

be individually configured for remote access.

NOTE: Provided software is PC compatible only; Mac OS® access to the

cameras is available via Safari® browser only.

Please see the Quick Start Guide or the documentation provided on the CD

for detailed software instructions. This manual only covers hardware

installation, network setup, and web browser configuration.

1.4.1 Milestone XProtect Go®

• Milestone XProtect® Go is a fully-featured client/server solution

providing mobile applications and remote access capabilities.

• Milestone XProtect® Go is free and requires a one-time annual

registration. Each year, you must renew your registration to continue

using Milestone XProtect® Go. Re-registration is also free.

• To view your installation from a smartphone or tablet, you can install the

freeMilestoneMobileServercomponentand XProtect®Mobile(available

as a free download on the App StoreSM and Google Play).

•MilestoneXProtect® Gosupportsup toeightIPcameras. Upgradeoptions

are available from Milestone.

• To upgrade your Milestone XProtect® software version, visit:

www.milestonesys.com/productoverview

• For Milestone XProtect® Go documentation and technical support, visit:

www.milestonesys.com/go/support

* See www.digimerge.com for the most updated list of third party VMS compatibility

Getting Started

1.4.2 Syncro-V

• Digimerge Syncro-V is a client-only solution that supports up to 36 IP

cameras. Syncro-V is a free software provided on the CD.

• Syncro-V supports all the features of the camera. It can access microSD/

SD card recordings and camera setup over a local network.

• Syncro-V manual is provided on the CD. For Syncro-V support, visit

www.digimerge.com

1.4.3 CMS-DH PRO

• Digimerge CMS-DH PRO is a client-only solution that supports up to 16

IP cameras. CMS-DH PRO is a free software available on

www.digimerge.com

• CMS-DH PRO allows you to view IP cameras and analog cameras from

your Touch Series DVR’s side-by-side via the virtual DVR feature. You can

view up to 64 screens at a time, including up to 16 IP cameras.

• CMS-DHS PRO does not support all the features of the camera, such as

microSD/SD card recording.

•CMS-DHPROmanual and support areavailablefromwww.digimerge.com

Connection

2. CONNECTION

The camera has the following termination cables:

1. RJ45 Network Interface: Connect to a router or switch on your network

using RJ45 Ethernet cable (Cat5e or better). 100Mhz connection. PoE

supported (class 3 PoE switch required).

NOTE: Use the included RJ45 coupler to connect to male end of RJ45

Ethernet cable.

RJ45 Coupler

2. Audio Input (RCA): Connect to a self-powered microphone for listen-in

audio.

3. Audio Output (RCA): Connect toan amplifier or self-powered speaker for

intercom/2-way audio.

4. DC12V (1A): 12V DC power input terminal. Make sure to follow correct

polarity (+/-) marked on the power connector when connecting to power.

• Minimum Power Requirement: 800mA / 9.6W.

Camera Installation

3. CAMERA INSTALLATION

1. Use the mounting plate or

template to drill holes for the

mounting screws and cables.

Align the mounting plate with

the TOP mark facing you. If

mounting the camera to a wall,

make sure that TOP mark is also

facing up. Attach the mounting

plate to the surface using the

mounting plate screws (4x).

Mounting plate

Mounting screw holes

TOP

NOTE: Use the included drywall

anchors if installing in drywall.

2. Make sure the hinge screw (1x)

is attached to the back of the

camera.

Hinge screw

Make sure to follow the correct polarity if connecting

the camera to DC power. Polarity is marked on the

power connector.

Camera Installation

3. Run the cables through the mounting plate. Align the TOP mark on the

camera base with the TOP mark on the mounting plate, rotate the

camera approximately 10° clockwise, and then rotate the camera

counterclockwise to slide the hinge screw into the notch on the mounting

plate. This will allow the camera to hang from the mounting plate while

you connect the cables.

Mounting plate notch

TOP mark on

camera base

TOP mark on

mounting plate

4. Connect the cables and then slide the camera to align the camera base

with the mounting plate. Attach the camera to the mounting plate using

the allen screws (4x).

Insert allen

screws

Slide the camera to align the camera

base with the mounting plate

4Rubber

gasket

Camera Installation

5. (Optional) Loosen the service compartment screw and open the service

compartment. The service compartment allows you to:

• Insert the included RCA-to-BNC test cable into the RCA output port and

connect the camera to a test monitor.

•InsertanSD card for localrecording. To enable recording, you must format

the microSD card and configure microSD recording. For details, see “6.9.1

Record Directory” on page 39.

NOTE: The camera supports microSD cards up to a maximum size of 64GB.

SanDisk™ or Kingston™ brand microSD cards are recommended.

• Check the POWER/NET LED to determine network status. The LED glows

orange if power is connected and flashes when the camera is connected

to the network.

RCA-to-BNC

test cable

SD card slot

Status LED’s

Camera Installation

6. Loosen the three allen screws on the camera stand to adjust the camera

viewing angle as necessary. Tighten the allen screws when finished.

ABC

• Screw Aallows you to rotate the camera 360°, independent from the

camera stand.

• Screw Ballows you to tilt the camera and camera stand 90°.

• Screw Callows you to rotate the camera and camera stand 360°.

7. Use a Philip’shead screwdriver to adjust the camera zoom and focus as

needed.

Focus Zoom

8. Close the service compartment and firmly tighten the service

compartment screw.

Finding the Camera’s IP Address

4. FINDING THE CAMERA’S IP ADDRESS

Use the steps below to find the camera’s IP address and connect to the

camera over the local area network (LAN) using Syncro-V, UPnP on

Windows® 7, or Bonjour® in Mac OS®.

4.1 Finding the Camera’s IP Address Using Syncro-V

1. Install Syncro-V from the CD or from www.digimerge.com. Double-click

the Syncro-V icon ( ) on the Desktop. The log in screen appears.

2. Under User Name and Password, enter the default Syncro-V user name

(admin) and password (admin). Click Login.

Enter Admin

Click Login

3. Syncro-V opens and scans the local network for connected cameras.

Detected camera IP addresses on the LAN appear in the Device List on

the left side of the screen with a icon.

Found camera

IP address

Finding the Camera’s IP Address

4. Click on a camera IP address in Device List to login.

5. Under User Name, enter the user name for the camera (default: admin).

Under Password, enter the password for the camera (default: admin).

Click Continue.

Click Continue to login

Enter Camera User Name

(default: admin)

Enter Camera Password

(default: admin)

6. The camera appears under the camera IP address. Click and drag the

camera to the display grid to open it.

Click and drag the

camera to the display

grid to open it

NOTE: For detailed instructions on using Syncro-V, see the Syncro-V

manual on the CD.

4.2 Finding the Camera’s IP Address using UPnP in

Windows® 7

NOTE: To use this method, your router must support UPnP and the camera

andcomputermustbe on thesamenetwork.UPnP is enabledinthecamera

bydefault,andcanbeenabled/disabledusing Syncro-V(checktheSyncro-V

manual for details).

Finding the Camera’s IP Address

1. Click Start>Computer>Network. The camera’s IP address appears

under Network Infrastructure.

Network

Double-click to open

the camera

2. Double-click the camera to open it in your default browser.

3. Under User Name and Password, enter the camera’s User Name

(default: admin) and Password (default: admin) and click Login.

Enter Camera User Name (default: admin)

Enter Camera Password (default: admin)

Click Login

4.3 Finding the Camera’s IP Address using Bonjour®in

Mac OS®

NOTE: To use this method, the camera and computer must be on the same

network. Bonjour® is enabled by default, and can be enabled/disabled

using Syncro-V (check the Syncro-V manual for details).

1. Open Safari® browser and click the Bookmarks button ( ).

Table of contents

Digimerge DNB14TL2 User manual