Digisol DG-BR4000N User manual

TM
DG-BR4000N
150Mbps Wireless Broadband Router
Quick Installation Guide
V1.1
2010-09-08

FCC Warning
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limitations are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Copyright © 2010. All rights reserved.
Company has an on-going policy of upgrading its products and it may be possible
that information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written
consent from the company.
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance could affect the user's authority to operate the equipment.
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet from that to which the receiver is
connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits
2
Trademarks:
TM
DIGISOL is a trademark of Smartlink Network Systems Ltd. All other trademarks are
the property of the respective manufacturers.

Package Contents
Thank you for purchasing DG-BR4000N 150Mbps 802.11n Wireless Broadband
Router! This router is the best choice for Small office / Home office users, all
computers and network devices can share a single Internet connection at high speed.
Easy Setup Utility is designed to setup an Internet connection in a very short time
without accessing the web configuration of the router. All computers and IEEE
802.11b/g/n wireless-enabled network devices (including PDA, cellular phone, game
console etc) can connect to this wireless router without additional cabling. With a
compatible wireless card installed in your PC, you can transfer data at a speed of up
to 150Mbps (transfer data rate).
The following items should be present in your package:
3
DG-BR4000N Wireless Broadband Router
Switching power adapter (12V DC, 0.5A)
Rubber feet (4 Nos.)
Vertical mount stand
Quick Installation Guide
Installation software CD (includes User Manual & Utility)
DIGILINK patch cord (1 No.)
Make sure that the package contains above items. If any of the listed items is
damaged or missing, please contact your retailer immediately.
Product Overview
System Requirements
The following system requirements are recommended
Notebook or desktop PC with network adapter (wired/WLAN)
Windows 2000/XP/Vista/7 Operating System
A web browser
AC power socket (100 – 240V, 50/60Hz)

Front View
DG-BR4000N has four 10/100Mbps RJ-45 port which can be connected to LAN or
PC and a 10/100Mbps RJ-45 WAN interface for connecting to Internet.
4
Product Overview
System Requirements
After installing the broadband router, you can verify its status from the
LED indicators on the front panel as shown below.
LED
Name
LED
Color
Light
Status
Description
P (Power) Green On The router is switched ON and correctly powered.
On Wireless WPS mode is enabled.
Off Wireless network is switched off.
WLAN Amber
Flashing Wireless LAN activity (transferring or receiving data).
On WAN port is connected.
Off WAN port is not connected.
WAN Green
Flashing WAN activity (transferring or receiving data).
On LAN port is connected.
Off LAN port is not connected.
LAN (1~4) Green
Flash LAN activity (transferring or receiving data).
Rear View

Interface Description
5
Product Overview
System Requirements
Rear View
Insert the Setup CD into your CD-ROM drive of notebook/desktop computer.
Router installation
Interfaces Description
Antenna It is a 3dBi dipole antenna.
Radio ON/OFF Switch the button to activate or deactivate the wireless functions.
After switching the button, the router will be reset automatically
for enabling the new setting.
Reset / WPS Reset the router to factory default settings (clear all settings) or
start WPS function. Press this button and hold for 10 seconds to
restore all settings to factory defaults, and press this button for less
than 5 seconds to start WPS function.
LAN (1 – 4) Local Area Network (LAN) ports 1 to 4.
WAN Wide Area Network (WAN / Internet) port.
Power Power connector, connects to A/C power adapter.

6
Explore the CD and execute the “EZ Wizard.exe” file. Below given screen will
appear. Click ‘Next’ to continue.
Connect one end of a network cable to the WAN port of the router and the other end to the DSL /
Cable modem. Click ‘Next’ to continue.

Connect one end of the provided network cable to one of the LAN ports (1~4) of the
router and the other end to your computer. Click ‘Next’ to continue with the installation.
7
Power ON the router. It will take approximately 30 seconds for router to boot up
completely. Ensure that all the LED’s on the router are ON. If not, try the above steps
again else click ‘Next’ to continue.

8
Enter the router’s password to log in to the router. The default password is
“1234”. It is recommended to change the router’s password to protect it from
being accessed by other users. If you do not wish to change the current
password, you can leave “New Password” and “Confirm Password” fields blank.
Click ‘Log in’ to continue.
Verify the “Internet Connection Type” the wizard has detected. If it is not correct
then please configure it manually. Click ‘Next’ to continue.

9
Note: If you are not sure which “Internet Connection Type” you use, then please
contact you Internet service provider for this information.
Enter the settings for your “Internet Connection Type”.
Click on ‘Clone’ to clone the MAC address of your PC with the WAN port of the
router, then click ‘Next’ to continue.
Dynamic IP (Cable Modem users)

PPPoE (DSL user)
Enter the username and password provided by your ISP, then click ‘Next’ to
continue.
10
Please wait while the wizard tries to connect to the Internet. If you see the
window “Internet Connection Succeed”, your router has been successfully
connected to the Internet. Please click ‘Next’ to configure the wireless settings.

Configure a name for your wireless network. Click ‘Next’ to continue.
11
Configure the security key for your wireless network. Select the check box for
‘Enable WPA Pre-Shared Key’. Enter 8 to 63 characters into WPA Pre-Shared Key.
Click ‘Next’ to continue.

12
Verify the settings you just configured for the router. Click ‘Finish’ to restart the
router. It will take about 60 seconds for router to reboot.
Congratulations! Your router configuration is now finished.
Users must configure their wireless notebook/desktop computer in order to establish
a wireless connection to the router. The following instructions help in establishing a
wireless connection between a Windows XP computer and the router.
Connect to the router wirelessly
Right click the wireless icon in the system tray and click on “View Available
Wireless Networks”.

A window displaying available wireless networks will open. Select the wireless
network you wish to connect and then click on ‘Connect’.
13
Enter the network security key if the wireless network you wish to connect has
wireless encryption enabled. Click ‘Connect’. The connection should now get
established.

Web Management of the router
To access the web configuration of the router, assign a static IP address to your
notebook/desktop computer in the subnet 192.168.2.X with the subnet mask
255.255.255.0 and gateway as 192.168.2.1. For example, assign the IP address
192.168.2.10.
Open a web browser and enter “http://192.168.2.1” in the address bar, press
‘Enter’. A login screen will appear, assign username as “admin” and password as
“1234”. Press ‘OK’ to Log in.
Following screen will appear on successful Login. You can now
configure the router through this web management page.
14

FAQ
Following are the solutions to problems that may occur during the installation and
operation of the DIGISOL DG-BR4000N Wireless LAN Broadband Router.
This product comes with Lifetime Warranty. For further details about warranty policy
and Product Registration, please visit support section of www.digisol.com
1. Router cannot get connected to Internet.
2. Wireless client cannot locate the router.
Verify whether ‘Broadcast ESSID’ is set to off in router’s web configuration.
Verify whether the antenna is properly connected and in correct direction.
Is your wireless client far away from your router? Try to get closer to the router.
Ensure that you input ESSID on your wireless client manually, if ESSID broadcast
is disabled.
Access the router’s web configuration and go to ‘Status’ -> ‘Internet Connection’
menu and verify Internet connection status.
If you were previously able to connect a computer to Internet directly, try to do that
again, and verify whether you can access Internet with your computer directly
attached to the device provided by your Internet service provider.
Check PPPoE user ID and password again.
Call your Internet Service Provider and verify whether there is some issue with
their service.
Try to reboot the router and verify whether it connects to Internet or not.
Try to use IP address instead of hostname. If you can use IP address to
communicate with a remote server, but can’t use hostname, please check DNS
setting.
15

1800-209-3444 (Toll Free)
[email protected] [email protected] www.digisol.com