Digitus RedRapid X User manual

RedRapid X
WIRELESS MODEM ROUTER
User’s Manual
(DN-7060)

COPYRIGHT
Copyright 2009/2010 by this company. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval
system, or translated into any language or computer language, in any form or by
any means, electronic, mechanical, magnetic, optical, chemical, manual or
otherwise, without the prior written permission of this company.

Federal Communication Commission
Interference Statement
FCC Part 68
This equipment complies with Part 68 of the FCC Rules. On the bottom of this
equipment is a label that contains the FCC Registration Number and Ringer
Equivalence Number (REN) for this equipment. You must provide this information
to the telephone company upon request.
The REN is useful to determine the quantity of devices you may connect to the
telephone line and still have all of those devices ring when your number is
called.
In most, but not all areas, the sum of the REN of all devices connected to one
line should not exceed five (5.0). To be certain of the number of devices you may
connect to your line, as determined by the REN, you should contact your local
telephone company to determine the maximum REN for your calling area.
If the modem causes harm to the telephone network, the telephone company
may discontinue your service temporarily. If possible, they will notify you in
advance.
But if advance notice isn't practical, you will be notified as soon as possible. You
will be advised of your right to file a complaint with the FCC.
The telephone company may make changes in its facilities, equipment,
operations, or procedures that could affect the proper operation of your
equipment.
If they do, you will be notified in advance to give you an opportunity to maintain
uninterrupted telephone service.
If you experience trouble with this modem, please contact your dealer for
repair/warranty information. The telephone company may ask you to disconnect

this equipment from the network until the problem has been corrected or you are
sure that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone
company. Connection to party lines is subject to state tariffs.
Installation
This device is equipped with a USOC RJ11C connector.
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.

FCC Caution
This equipment must be installed and operated in accordance with provided
instructions and a minimum 20 cm spacing must be provided between computer
mounted antenna and person’s body (excluding extremities of hands, wrist and
feet) during wireless modes of operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure Statement
This equipment complies with FCC radiation exposure set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the FCC
radio frequency exposure limits, human proximity to the antenna shall not be less
than 20cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.

R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC OF
THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on radio
equipment and telecommunication terminal Equipment and the mutual
recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station Equipment)
As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacture must therefore be allowed at
all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not intended for use
None.

Contents
1. INTRODUCTION................................................... 1
1.1. FEATURES ...................................................................2
1.2. MINIMUM REQUIREMENTS.............................................3
1.3. PACKAGE CONTENT .....................................................3
1.4. HARDWARE PLACEMENT...............................................4
1.4.1. Rear Panel....................................................................... 4
1.4.2. Front LEDs....................................................................... 5
2. HARDWARE INSTALLATION.............................. 6
3. SETUP WIZARD................................................... 7
3.1. GETTING STARTED.......................................................7
3.2. AUTOMATICALLY SET ISP...........................................10
3.3. MANUALLY SET ISP....................................................14
4. IP ADDRESS SETTING...................................... 19
5. WEB MANAGEMENT CONFIGURATION ......... 24
5.1. QUICK SETUP.............................................................26
5.2. GENERAL SETUP........................................................29
5.2.1. System........................................................................... 29
5.2.1.1. Time Zone..............................................................................29
5.2.1.2. Password Settings..................................................................30
5.2.1.3. Remote Management.............................................................32
5.2.1.4. SNMP.....................................................................................34
5.2.2. WAN............................................................................... 36
5.2.2.1. Channel Config.......................................................................36
5.2.2.2. ATM Setting............................................................................41
5.2.2.3. ADSL Setting..........................................................................43
5.2.2.4. DNS........................................................................................45
5.2.2.5. DDNS.....................................................................................47
5.2.2.6. RIP.........................................................................................48
5.2.3. LAN................................................................................ 51

5.2.3.1. DHCP Mode...........................................................................52
5.2.3.2. DHCP Relay...........................................................................53
5.2.3.3. DHCP Server..........................................................................54
5.2.3.4. ARP Table..............................................................................57
5.2.3.5. Bridging..................................................................................57
5.2.4. Wireless......................................................................... 59
5.2.4.1. Basic Settings.........................................................................59
5.2.4.2. Advanced Settings .................................................................62
5.2.4.3. Security ..................................................................................66
5.2.4.4. Access Control.......................................................................69
5.2.4.5. WPS.......................................................................................71
5.2.5. QoS................................................................................ 73
5.2.6. NAT (Network address translations).............................. 77
5.2.6.1. Port Forwarding......................................................................77
5.2.6.2. Port Mapping..........................................................................79
5.2.6.3. UPNP .....................................................................................81
5.2.6.4. IGMP Proxy............................................................................82
5.2.7. Firewall........................................................................... 84
5.2.7.1. IP/Port Filtering.......................................................................84
5.2.7.2. MAC Filtering..........................................................................86
5.2.7.3. URL Blocking..........................................................................88
5.2.7.4. Domain Blocking ....................................................................90
5.2.7.5. Routing Configuration.............................................................91
5.2.7.6. ACL Configuration..................................................................93
5.2.7.7. DMZ .......................................................................................94
5.3. STATUS .....................................................................96
5.3.1. Interface......................................................................... 97
5.3.2. ADSL.............................................................................. 98
5.4. TOOLS.......................................................................99
5.4.1. Configuration Tools........................................................ 99
5.4.2. Firmware Upgrade ....................................................... 100
5.4.3. Ping.............................................................................. 100
5.4.4. ATM Loopback............................................................. 101
5.4.5. ADSL............................................................................ 103
5.4.6. Diagnostic Test............................................................ 104

5.4.7. Reboot ......................................................................... 104
6. TROUBLESHOOTING...................................... 105
7. GLOSSARY ...................................................... 109

1
1. Introduction
Congratulations on purchasing this Wireless N ADSL2/2+ Router. This router is a
cost-effective ADSL2/2+ router, with the combination of an ADSL2/2+ modem,
router, Ethernet network switch and wireless access point, you can surf the
Internet through your ADSL2/2+ ADSL connection without investing other
devices.
This router can support downstream transmission rates of up to 24Mbps and
upstream transmission rates of up to 1Mbps. It supports PPPoA (RFC 2364 -
PPP over ATM Adaptation Layer 5), RFC 1483/2684 encapsulation over ATM
(bridged or routed) and PPP over Ethernet (RFC 2516) to establish a connection
with ISP. The product also supports VC-based and LLC-based multiplexing.
With the web management interface, users can easily configure the various
functions of the router including DHCP server, NAT, port forwarding, DMZ,
access control, IP/MAC/Port filtering, QoS, Firewall, PPTP/IPSec/L2TP pass-
through, DDNS, UPnP, Wireless and etc.
This router is a high performance and high-speed device that provides a full rate
of ADSL2+ standard with the superb reliability and a complete solution for home
and office application.