Digitus DN-70591 User manual

WIRELESS 11N 300MBPS
BROADBAND ROUTER
Quick Installation Guide
DN-70591

INTRODUCTION
DN-70591 is a combined wired/wireless network connection device
designed specifically for small business, office, and home office networking
requirements. It complies with the IEEE 802.11n (Draft 2.0) standard. It
adopts MIMO as well as SST technologies. It also works well with other
11b/g and 11n protocol wireless products. Create instant WiFi hotspots at
any location where you have Internet connection
Package Contents
Before you starting to use this router, please check if there’s anything
missing in the package, and contact your dealer of purchase to claim for
missing items:
•1 x Wireless Router
•1 x Quick installation Guide
•1 x Power adapter

GETTING STARTED
Setting up a Wireless Infrastructure Network
For a typical wireless setup at home (as shown above),
Please do the following:
1. You will need broadband Internet access
(a ADSL, Cable Modem line into your home or office)
2. Consult with your ADSL or Cable Modem provider for proper
installation of the modem
3. Connect the ADSL or Cable modem to DN-70591
Plug in the Power Adapter to the Wireless-N Router
4. Connect your computer/notebook to the DN-70591
IMPORTANT NOTE
You can reset this Wireless Router to default setting
by press the ‘RESET’ button on the back side of the
Router for more than 8 seconds
You can use this solution if you forget your
password.

Adding computers to the Wireless-N Router
1. Log on to the computer.
2. Open Connect to a Network by right-clicking the network icon ( or
) in the notification area.
3. Choose the wireless network from the list that appears, and then click
Connect.
4. Type the network security key or passphrase if you are asked to do so,
and then click OK.
You'll see a confirmation message when you are connected to the
network.
5. To confirm that you added the computer, do the following:
Open Network by clicking the Start button , and then clicking
Control Panel. In the search box, type network, and then, under
Network and Sharing Center, click View network computers and
devices.
You should see icons for the computer you added and for the other
computers and devices that are part of the network.
Note: If you don't see icons in the Network folder, then network discovery
and file sharing might be turned off.
For more information:
http://windows.microsoft.com/en-US/windows7/Add-a-device-or-computer-to-a-network
http://windows.microsoft.com/en-US/windows7/Setting-up-a-wireless-network
http://windows.microsoft.com/en-US/windows-vista/Setting-up-a-wireless-network

CONFIGURING VIA WEB BROWSER
Open web browser and type http://192.168.0.1 in the browser's address
box. This number is the default IP address for this device.
The login screen below will appear. Enter the “User Name” and “Password”
and click “OK” to login.
The default User name is “admin” and the Password is “admin”,

Change management password and language
Default password of Wireless Router is “admin”, and it’s displayed on the
login prompt when accessed from web browser. There’s a security risk if
you don’t change the default password, since everyone can see it. This is
very important when you have wireless function enabled.
To change password, please follow the following instructions:
Please click ‘Management -> Management ‘menu on the web
management interface, the following message will be displayed on your
web browser:

Setup Wizard
After successfully login, the following Router Summary will be displayed on
your web browser:
The setup wizard will guide you to configure access point for first time.
Please follow the setup wizard step by step.
The Wizard will guide you the through following steps. Begin by clicking on
Next.
1. Gateway
2. Bridge
3. Wireless ISP
For Internet access to connect to the ADSL modem at home, please select
“Gateway” mode to proceed with the wizard.

Then follow the wizard to the Time Zone setting where you can manually
change the Time Zone according to your area.

Then for LAN setting, you can change it to your desired IP address for the
Gateway or you can simply keep it unchanged as default.
For WAN setting, you have 3 options of Static IP, DHCP Client and PPPoE.
For most of the application to connect DN-70591 to the ADSL modem,
please select PPPoE and then key in the account and password of your
ADSL account.

For “Wireless Setting”, you can change the SSID to your desired name.
For “Wireless Security Setup”, you can add your own password for WiFi
access. Please note that the factory default of the encryption is turned OFF.

Then this is the end of the Setup Wizard. You should now be able to access
Internet via WiFi connection.
LAN Settings
Please click “Network
 Lan Settings” located at the web management
interface, the following message will be displayed on your web browser:
IP Address: Enter the IP address of your Router or reset it to the
factory default as 192.168.0.1
Subnet Mask: An address code that determines the size of the network.
Normally use 255.255.255.0 as the subnet mask.
DHCP Type: Server, Client or Disable
Note:
1) If you change the IP Address of LAN, you must use the new IP
Address to login the Router.
2) If the new LAN IP Address you set is not in the same subnet, the IP
Address pool of the DHCP server will change accordingly at the same
time，while the Virtual Server and DMZ Host will not take effect until
they are re-configured.

Connect to Internet (Gateway)
Please click “Network
 WAN Settings” located at the web management
interface, Following example is for “PPPoE” WAN setting.
Enter the “Username” and “Password” that ISP provided and leave the
others. (The “Service Name” can be blank)
Click “Apply Changes” button to save the settings then reboot the router.
After reboot, your router is now ready for Internet connection.
If your ISP provides a static or fixed IP Address, Subnet Mask, Gateway
and DNS setting, select ‘Static IP’.
Enter the IP address / Subnet Mask / Default Gateway / MTU / Primary /
Secondary DNS in dotted-decimalnotation provided by your ISP.

If your ISP provides the DHCP service, please choose ‘DHCP Client’, and
the Router will automatically get IP parameters from your ISP.
This page displays the WAN IP parameters assigned dynamically by your
ISP, including IP address, Subnet Mask, Default Gateway, etc.

Wireless Band Setting
Please click “Wireless -> Basic Setttings” located at the web
management interface, the following message will be displayed on your
web browser:
You could configure the minimum number of Wireless settings for
communication, such as Network Name (SSID) and Channel. The Access
Point can be set simply with only the minimum setting items.
Enable Wireless Wireless On/Off
Network Mode: Supports 11a/11b/11d/11n mixed modes.
SSID: Main Service Set Identifier. It’s the "name" of your
wireless network.
Channel This field determines which operating frequency will
be used. The default channel is set to Auto, so the
AP will choose the best channel automatically. It is
not necessary to change the wireless channel
unless you notice interference problems with
another nearby access point.

Wireless Security
Please click “Wireless-> Wireless Security” located at the web
management interface, the following message will be displayed on your
web browser:
Setup the wireless security and encryption to prevent from unauthorized
access and monitoring. Supports 64/128-bit WEP, WPA, WPA2 encryption
methods.
When you finish, click ‘Apply Changes‘.
Please click “Wireless-> WPS” located at the web management interface,
the following message will be displayed on your web browser:
you can establish a wireless connection between wireless adapter and
Router using either Push Button Configuration (PBC) method or PIN
method.

Disable WPS: Enable / Disable
PIN method: If the new device supports Wi-Fi Protected Setup and the
PIN method, you can add it to the network by PIN
PBC method: If the wireless adapter supports Wi-Fi Protected Setup,
and the Push Button Configuration (PBC)
Step 1: Press the WPS button of the Router directly
for 2 ~ 3seconds or Click web management interface
‘PBC’and ‘Apply Changes‘
Step 2: Press the WPS button of the Adapter directly
for 3 seconds
Step 3: Wait for a while until the next screen appears.
Click Finish to complete the WPS configuration

ROUTER ADMINISTRATOR SETUP
Factory Default
You can backup all Setting of this router to a file, so you can make several
copied of router configuration for security reason.
To backup or restore router setting, please follow the following instructions:
Please click click ‘Management-> Save/Reload Settings’ located at the
web management interface, then the following message will be displayed
on your web browser:
Reset Settings to
Default
Click this ‘Reset‘ button to remove all settings you
made, and restore the configuration of this router back
to factory default settings
Browse

Firmware Upgrade
The system software used by this router is called as ‘firmware’, just like any
applications on your computer, when you replace the old application with a
new one, your computer will be equipped with new function. You can also
use this firmware upgrade function to add new functions to your router,
even fix the bugs of this router.
Please click ‘Management-> Upgrade Firmware’ located at the web
management interface, then the following message will be displayed on
your web browser:
Click ‘Browse…’ button first, you’ll be prompted to provide the filename of
firmware upgrade file. Please download the latest firmware file from our
website, and use it to upgrade your router.
After a firmware upgrade file is selected, click ‘Upgrade‘ button, and the
router will start firmware upgrade automatically. The procedure may take
several minutes, please wait for this process to complete.
NOTE: Never interrupt the upgrade procedure by closing the web browser
or physically disconnect your computer from router. If the firmware you
uploaded is corrupt, the firmware upgrade will fail, and you may have to
return this router to the dealer of purchase to ask for help. (Warranty voids if
you interrupted the upgrade procedure).
Browse..