Direct IP IDIS DA-EC1101R User manual

Powered by
Ethernet
over Coax
Transceiver
DA-EC1101R
DA-EC1101T
Operation Manual

2
Before Using the Product
FCC Compliance Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at
his own expense.
User’s Caution Statement
Caution: Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void your authority to operate the equipment.
Product Overview
DA-EC1101R / DA-EC1101T is a networking device(EOC: Ethernet Over Coax) that uses
coaxial cables. It makes it possible to supply Power over Ethernet and transmit data
between a network camera that uses RJ45 port and a DVR using coaxial cables.

3
Product Features
●Makes it possible to install Full-HD network cameras using existing coaxial cables.
●10/100Base-T two-way communication allows use of the product as a transmitter or
a receiver.
●Supports PoE (IEEE 802.3af, IEEE 802.3at)
●Supports Plug & Play without setting up special IP addresses.
●Supports up to 800 meters in distance.
Accessories
The product consists of the following components.
BNC
48VDC
RJ45
Power
PoE
Mac Address
Main unit
(DA-EC1101R /
DA-EC1101T)
48V DC adapter &
220V power cable
(DA-EC1101R only)
Operation Manual MAC address
sticker
MAC Address is required for warranty services. Please keep the sticker attached on the product.
First, connect the adapter to the product. Then, turn the device On. If the adapter is connected while the
switch is turned On, it may cause an electric spark. Be careful when using the product at a gas station or
near combustible substances.

4
Overview
Front
DA-EC1101T DA-EC1101R
BNC
48VDC
RJ45
Power PoE
Power LED (Blue)
BNC LED (Green)
RJ 45 LED (Green)
RJ 45 port
Power input
1
2
3
4
5
BNC
48VDC
RJ45
Power Network
Power LED (Blue)
BNC LED (Green)
RJ 45 LED (Green)
RJ 45 port
Power input
1
2
3
4
5
Back
DA-EC1101T DA-EC1101R
Coax Data
PoE Switch
Coax Data
(no analog video)
6
7Coax Data
Coax Data
(no analog video)
7
1Power LED LED turns on when power is connected.
2BNC LED LED turns on when BNC cable is connected.
3RJ 45 LED LED turns on on when a RJ45 UTP cable is connected.
4RJ 45 port Use the RJ45 port to connect the UTP cable.
5Power input Connect a 48V DC adapter. Connect the adapter first before
turning the device On.
6PoE Switch
Turns PoE On or Off.
Turn PoE Off if the product connected to the RJ45 port does not
support PoE power input. Its factory default is set to Off.
7Coax Data Connect BNC cable.

5
Installation
1 Connect DA-EC1101R's RJ45 port to the Video In port or a hub attached to a Video
In port of DirectIP™ NVR using a network cable.
2 Connect DA-EC1101T's RJ45 port to the network port of DirectIP™ camera using
a network cable.
If DA-EC1101T EOC requires PoE power supply, turn the PoE Switch of DA-EC1101T to On.
3 Connect DA-EC1101R and DA-EC1101T using a coaxial cable.
4 Connect the included 48V DC adapter to the Power Input port of DA-EC1101R.
First, connect the adapter to the product. Then, turn the device On. If the adapter is connected while the
switch is turned On, it may cause an electric spark. Be careful when using the product at a gas station or
near combustible substances.
5 DA-EC1101R and DC-EC1101T will turn on at the same time and the 48V DC LED
on the product will be lit.
6 Refer to the installation layout and install the product.

6
Installation Layout
48V DC
power input
DA-EC1101T
DA-EC1101R
Network
<2,625 ft (800m)
DirectIP™ NVR
Turn the PoE
Switch to Off
if the attached
device does not
support PoE.
Specifications
Model DA-EC1101R / DA-EC1101T
RJ45 10/100
Coaxial cable 3C or higher
Power 48V
Maximum data transfer distance 800m (Distance varies by class when using PoE
transmission.)
Maximum data transfer speed 95Mbps
PoE IEEE802.3af, IEEE 802.3at
Weight 150g
Dimensions (W)X(D)X(H) 100 X 43 X 39 (mm)
Types of Cables
UTP Cable (Data only)
BNC Cable (DATA + Power)
DC Power

IDIS Co., Ltd.
For more information, please visit at
www.idisglobal.com Ver. 1.00