Distek VIP 4400 Programming manual

Document No. 3844-0001
Quick Start Instructions
VIP 4400 Vessel Washer
DISTEK, INC. Rev: A 3844-0001
Quick Start Instructions: VIP 4400 Rev Date: 01/17/05 Page 1 of 2
Filling the Rinse Tank
•Do not leave the instrument unattended while
filling the rinse tank.
•Max allowable water source pressure: 30
PSI.
1. Roll the unit near the water source (faucet, DI water dispenser, etc…) that will
be used to fill the rinse tank and lock the 2 front casters.
2. Connect the tubing supplied with the unit to the quick-connect fitting located
on the top cover.
3. Connect the other end to the water source.
4. Turn on the water source.
5. When the tank is full the water source will automatically stop (the unit is
equipped with an internal water shutoff). If the unit is powered on, the FULL
LED for the Rinse Tank will be illuminated.
6. Disconnect the tubing from the quick-connect fitting on the top cover of the
unit.
The internal water shutoff valve will only stop the
water from flowing into the rinse tank, it will not
shutoff the water source!
Using the Vessel Washer
1. Plug in the instrument and turn
the power button on.
2. Select desired Wash Cycle on the
main keypad.
3. Remove the Universal Wash
Module (UWM) from the top cover
and insert the UWM into the
vessel to be cleaned (see Figure
1).
4. Press the AUTO WASH button on
the UWM.
5. Upon completion an audible beep
will be heard.
6. Remove the UWM and insert into
the next vessel.
7. When all vessels have been
cleaned return UWM into the top
cover.
Figure 1: Universal Wash Module

Quick Start Instructions
VIP 4400 Vessel Washer (continued)
DISTEK, INC. Rev: A 3844-0001
Quick Start Instructions: VIP 4400 Rev Date: 01/17/05 Page 2 of 2
In order to remove most of the residual media from
the wash cycle, it may be necessary to remove the
UWM from the vessel, gently shake UWM above the
vessel, reinsert it into the vessel and execute a
manual drain.
Setting the Heater (Optional)
The optional heating module allows the rinse media to be heated up to 60ºC prior to
cleaning the vessels. This allows for a more efficient wash. Pressing the
ON/OFF/SET button will toggle the heater on and off.
1. Ensure the unit is powered on.
2. Press and hold the ON/OFF/SET button on the main keypad.
3. The temperature display will begin blinking. Using the Up or Down Arrow
Keys change the blinking display to the desired set temperature.
4. Press and hold the ON/OFF/SET to confirm the new set temperature.
5. Press the ON/OFF/SET button to activate the heater. The Heater LED should
be illuminated illustrating that the unit is now heating.
6. Once the set temperature is reached (the display will update as the tank heats)
the unit is ready for operation.
Emptying the Waste Tank
The tubing supplied with the unit MUST be
connected to the quick-connect port located on
the rear cover prior to trying to empty the Waste
Tank.
Prolonged storage of acidic media in the Waste Tank
can cause irreversible damage to the tank. It is
recommended to empty the Waste Tank everyday.
1. Connect the supplied tubing to the quick-connect fitting located on the rear
cover.
2. Place the other side (outlet) of this tubing into the waste containment area
(waste drum, sink, etc…).
3. Power the unit on.
4. Press the Empty Waste Tank button located on the rear cover for 2-3 seconds
to activate the waste pump.
5. When the Waste Tank is empty the draining will automatically stop. If
necessary press and hold the Empty Waste Tank button to ensure the tank is
completely empty