DoHonest 1080P Backup Camera User manual

1
USER MANUAL
1080P BACKUP CAMERA KIT
Note:p
lease goto download latest instruction manuals!
Note2: please read the manual carefully before using !

2
What ’s in the Box?
Note: Details may change based on item configuration
FEAT URE
• Camera built-in Microphone & monitorbuilt-in speaker: You can get the
video sound while driving or parking.
• Multi-function and Multi-channel Signal Input - Equipped with
independent green reversing trigger line.
• The centralized power cord is powered by the power supply on the fuse
boxin cab, eliminating the tedious steps of disassembling and installing the
tail lamp.
• Systemcan be installed to turn on only when vehicle is in reverse, or

3
wired for continuous viewing.
• Best fit for heavy-duty vehicles: RV, Motorhome, Large truck, travel
trailer, box truck, etc.
• Meets FCC/CE standards
PARTS IDENTIFICATION

4
INTRODUCTION
This manual contains instru ctions to make the installation of the camera

5
and monitoreasier. The color backup camera system is a supplement to
standard rear-view mirror sys tems, and will p rov ide additional rear-view
vision when installed and maintained properly. It is not intended in any
way to be a substitute for careful and cautious driving.
GE TTING START ED
TES T THE S YS TEM
We recommend doing a benchmark test before installation to insure that all
components are working properly.To ensure the s ystem works properly
after installation, all components should be tested and checked before
installation.
Firstly, refer to the what’s in the box page to check whether the component
is missing. We do not rule out that some components may be damaged in
the case of violent loading and unloading during transportation.
If so, please contact us in time.
Secondly, connect the powercable(9 pin connector) to the monitor, the
pos it ive an d negat ive terminals t o 12-32v voltage, then the power indicator
will turn blue and all the buttons into blue backlight, indicating the
successful test of the display, can work normally.
Finally, connect 4-pin connector(the otherend of the power cable)to the
backup camera, restart the power supply of the monitor, and the
corresponding channel image will appear, If display normally, so the
backup camera is working properly. If not please refer to the
troubleshooting.
Note: The monitor can only display the image of the camera of the
corresponding channel, if your camera is connected to the AV1 channel,
please s witch the monito r to AV1.
B EFO R E B EG IN N IN G IN S TA LLAT IO N
As the camera needs to be fixed on the vehicle, it may need to drill a
hole on your car, before drilling please measure the size ofboreholes and
check that no cable or wiring is on the other side of the wall.
Keep all cables away fromhot or moving parts and electrical noisy
components.
Pleas e clamp all wire s s ecure ly to redu ce th e poss ib ility o f th em being
damaged while vehicle is in use.
INSTALLATION GUIDE
SYS TEM CONNECTION DIAGRAM

6
RECOMMENDED INSTALLATION LOCATION
Camera: close to rear marker lights, centered on vehicle.
Monitor: dash boa rd
CABLE CONNECTION
RED wire to ignition hot (+) 12-32 vo lts .
BLACK wire to ground (-) (please us e a chass is ground post).
GR EEN trigger wire is for CH2 camera channel.
Connects g reen trigger wire to backup light wire orbackup beeper wire.
T h is connection is needed to activ ate the monitor when putting the vehicle
into reverse.

7
POWERED BY CIRCUIT FUS E
Firstly, recommended and connect the RED Wire(ACC+) to the fuse
s witch.
Secondly, find the car circuit fuse boxunder your car cab.
Finally, according to the labels on the fuse hardwire to find the
corresponding power fus e
and connect the corresponding line (voltage must between 12-32V).
Note: If connecting power directly to battery, the camera is always ON and
therefore can drain battery. Therefore it is recommended to connect power
to an ignition switched accessory powersource.
INS TALLATION CAMERA
Firstly, find the best ins tallation pos ition to install backup camera on your
vehicle,e.g. close to rear marker lights, centered on vehicle.
Secondly, remove the camera U-bracket, mark the hole position with a
marker pen, then drilling, after the hole is finished, route the terminal wire
of the camera through it and install the screwof the backup camera.
Finally,adjust the best angle.
INS TALLAT ION MON ITO R
Firstly, Find thebest installation position toinstall monitor in your vehicle.
Se condly, Remove the screw around then take out the monitor.Put
U-bracket to the ri ght plac e and adj us t an gl e, pr epar e 2 scr ews .
Thirdly, Locking the bracket by screws . Put the moni tor into bracket a nd
lockingit.
Finally, adjust the best angle to allow optimum driver viewing comfort by
th ems el f.
O PE R AT I ON GUIDE
REMOTE CONTROL
Power button
Video select button
Left arrow(Positive/increase) button
Menu button
Right arrow(Negative/decrease)button
Mode select button:rotate flip ima g e /n ormal/mirro r image s ett ing
FUNCTIONS OPERATE
V1/V2 button: switch CH1 and CH2 channel camera.
Mo de but ton: rotate flip ima g e/normal/mirror imag e setting.
Power button: turn on/off and stadnby.

8
Menu button pr es s 1 ti mes: enter brightness ad just mo de , pres s +/ - to
increase/ de creas e the value,wait 10 s econds to exit setup mode,valid value
is 0—40,factory default value is 20.
Menu button pr es s 2 ti mes: enter contrast ad just mo de , pres s +/ - to
increase/ de creas e the value, wait 10 seconds to exit setup mode,valid
value is 0—40,factory default value is 20.
Menu button press 3 ti mes: enter color adjust mo de , press +/- to
increase/ de creas e the value, wait 10 seconds to exit setup mode,valid
value is 0—40,factory default value is 20.
Menu button press 4 ti mes: enter language ad just mod e , pres s +/ - to
increase/ de creas e the value, wait 10 seconds to exit setup mode,valid
value is English,Francais …,factory default value is English.
Menu button press 5 ti mes: enter default setting mode, pr es s +/ - to
increase/ de creas e the value, wait 10 seconds to exit setup mode,
No tes : valid item is brightness,contrast,color,volume,rulersetting
only,invalid item is language RLUD,VCOM.
Menu button press 6 ti mes: enter volume adjust mode, pres s +/ - to
increase/ de creas e the value, wait 10 seconds to exit setup mode, valid
value is 0—40,factory default value is 20.
Menu button press 7 ti mes: enter RLUD adjust mode(normal/mirror
flip rotate image), pres s +/ - to increase/ decrease the value, wait 10
seconds to exit s etup mode, valid value is 1,2,3,4, th is s e lect ion ro tate/flip
each camera image individually both horizontally and vertically, This
allo ws for a correct image of front/rear camera, e.g. 4--rear camera,
3--front camera, effect individually both CH1and CH2.
Menu button press 8 ti mes: enter VCOM adjust mode, press +/- to
increase/ de creas e the value, wait 10 seconds to exit setup mode, valid
value is 0—40,factory default value is 20.
Menu button press 9 ti mes: enter ruler s etting adjust mode(parking
guideline), pr es s +/ - to increase/ decreas e the value, wait 10 seconds to exit
setup mode. Note:valid setting fo r CH2 channelonly, invalid settingfor
CH1 channel.
Menu button press 10 times: enter vers ion check mode, wait 10
seconds to exit s etup mode, reserve only.
Parking guideline setting:same as “Menu button press 9 t ime s”.
Mirror image setting: same as “Menu button press 7 t ime s”.

9
SP EC IF IC AT IO N & DIME NSION
Camera
Image Sensor
1/3” Color CMOS
TV System
NTSC(1080P/30fps)
Effective Pixels
1920(H)x1080(V)
Horizontal Sync Frequency
33.750KHz
Vertical Sync Frequency
30Hz
Electronic Shutter
1/30~1/60 Seconds
Scanning System
Progressive Scanning
Sync System
Internal
Resolution 1080P
Video Output
AHD,1.0Vp-p,75Ohm
White Balance
Auto
Power Supply
DC12V
Waterproofrating
IP 69 K
ViewingAngle
120˚
Audio
Yes
Minimumlllumination
0 Luxwith IR ON
Night visiondistance
8-10m
Image mode
Mirror ima g e
SMART IR-CU T
Yes
Operating Temperature
-30~70,RH90% MAX
Storage Temperature
-40~80,RH90% MAX
Monitor
LCD Size
7” lcd color monitorwith digital IPS Panel
Resolution
1024x3(RGB)x600
Brightness 550cd/m2
Contrast
600:1
View angle
U/D:85˚;L/R:85˚
Power Supply
DC9-36V
Power Consumption
about 6W
Support Audio intput hannel
CH1, CH2
Built-inLoud Speaker
Yes (1W)
Screen Mode
16:9
Support Video System
1080P/720P/CVBS auto detection

10
OSD menu,Remote Control Mirror/Normal Flip Image,Guideline
ON/OFF,Brightness,Contrast,Color,volume
Outline Dimension
4.6 ”(H)x7”(L)*8.2”(D )
Extension Cable
Length
50ft
Feature1
Pure copper wire
Feature2
Double shielding:tinfoil wrap up and copper wire winding
TROUBLESHOOTING
If you have any questions about this product, Please send us an mailbox
above!
Monitor will not po we r -up (the power indicator LED lights is always
off)
Check fus e
Check 12v+ to monitor
Check ground connection
Check this product within the voltage range(12-32V) specified.
No signal/blue on monitor screen
Do a hard reset,unplug all cables, leave out for 1 minute and then
re-connect them.
Check to ensure that the connection to the camera is tight.
Verify camera cable is plugged into port labeled backup camera
Verify that the red positive trigger on power harness cable is put to
power 12v+.
No image on screen
Verify camera is on correct camera input
Verify cable is connected to monitor
Verify camera is connected to cable
Connect known working camera and cable to monitor.
No audio on camera
Verify volume setting
Verify chosen camera has audio function.
Verify chos en extension cable has audio wire
Wr ong normal/mirror image setting
Verify RLUD(normal/mirror flip rotate imag e) setting,
e.g. mirror image:rear camera; normal image:front/side camera.
Verify chosen camera has mirror
No par k i ng g ui de li ne on camera
Verify ruler setting is on