Dominator SPB-IG2 User manual

INSTALLATION GUIDE
MODEL #: SPB-IG2
SQUARE INGROUND PICKLEBALL POLE
SECTION 1:
SECTION 2:
SECTION 3:
SECTION 4:
Safety Instructions
Anchor Sleeve Installation
Post Installation/Net Assembly
Warranties & Policies

*Save this instruction sheet in the event that the manufacturer has to be contacted for replacement parts.
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND
WILL VOID WARRANTY.
Owner must ensure that all players know and follow these rules for safe operaon of the system.
To ensure safety, do not aempt to assemble this system without following the instrucons carefully. Check the
enre box and inside all packing material for parts and/or addional instrucon material. Before beginning
assembly, read the instrucons and idenfy parts using the hardware idenfier and parts list in the instrucons.
Proper and complete assembly, use, and supervision are essenal for proper operaon and to reduce the risk of
accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and
operated properly.
Most injuries are caused by misuse and/or not following instrucons. Use cauon when using this system.
SAFETY INSTRUCTIONS
SECTION 1: SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN
SERIOUS INJURY AND/OR PROPERTY DAMAGE
Do not climb or play on net.
When adjusng net or moving system, keep
hands and fingers away from moving parts.
During play, do not wear jewelry (rings, watches,
necklaces, etc.). Objects may entangle in net.
Check system before each use for loose hardware
and instability. Repair before each use. Never
play on damaged equipment.
WARNING
!!
801.769.4663
BEFORE digging for the Inground Sleeve
installation, contact your local call-be-
fore-you-dig phone number so you don’t
unintentionally dig into an underground
utility line.

SECTION 2: ANCHOR SLEEVE INSTALLATION
Dig two holes 20’ apart to the appropriate depth and dimensions shown above. *NOTE: These dimensions are provided
as a guideline; local frost and soil conditions should be considered. Distance between inside face of both posts should
be 22’.
Mix concrete. Partially fill each hole until concrete is 16” from the playing surface. See Figure 1.
Remove Anchor Sleeve Cap (Item #1). Insert both Anchor Sleeves (Item #2) into the hole in the concrete. See Figure 2.
The Anchor Sleeves should be 22’ apart from the inside face of each post.
INSTRUCTIONS
STEP 1:
Using a level, ensure each Anchor Sleeve is flush with the playing surface and perfectly aligned.
STEP 3:
STEP 2:
STEP 4:
DIMENSIONS
36”
16”
30”
24”
PARTS USED
TOOLS REQUIRED
Periodically check the alignment and height of the Anchor Sleeves while allowing the concrete to partial-
Replace Anchor Sleeve Cap and fill the
rest of the hole with concrete. See
Figure 3 and 4.
Allow concrete to to cure for 72 hours
before installing posts.
STEP 5:
STEP 6:
STEP 7:
Level
Concrete
Shovel Tape Measure
Figure 1
16”
Figure 2
Figure 3 Figure 4
Item # Part Number
Part Description
1
2
Qty
SPP3-DWG-004
SPP3-DWG-003
Anchor Sleeve Cap
Anchor Sleeve
2
2
1
2

SECTION 3: POST INSTALLATION/NET ASSEMBLY
***ENSURE GROUND SLEEVE & CONCRETE HAS HAD AT LEAST 72 HOURS TO SET.
Remove the screw from the Crank Handle (Item # 3) and attach the Crank Handle
to Post A (Item #1). Replace the screw and tighten. See Figure 1.
Slide Height Collar (Item #4) onto each pickleball post with the eyebolts facing
inward, on the same side as the lacing rod. See Figure 2.
Remove cap from the Anchor Sleeve and slide pickleball post into the sleeve
with the lacing rod facing inwards, towards the other post. Repeat on other
side. See Figure 3 & 4.
INSTRUCTIONS
STEP 1:
STEP 3:
STEP 2:
TOOLS REQUIRED
Tape Measure
Figure 3
Item # Part Number
Part Description
1
2
3
4
5
6
Qty
SPP3-ASM-001
SPP3-ASM-002
SPP3-ASM-007
SPP3-ASM-008
RPP-DWG-031
RPP-DWG-032
Post A
Post B
Crank Handle
Height Collar
Heavy Duty Net
Lacing Cord
1
1
1
2
1
1
PARTS LIST
6
5
Figure 4
Figure 1
Figure 2

Loosen the eyebolt on the Height Collar and using a tape measure, adjust the height of the
pickleball posts to 36”. Retighten eyebolts. See Figure 5.
Unwind the Heavy Duty Net (Item #5) and lay it out across the court.
Place one end of the top cord cable over the pulley of Post B (Item # 2) and attach the cable
loop around the net hook on the backside of the post. See Figure 6 & 7.
Place the other end of the top cord cable over the pulley of Post A and attach the loop around the screw on the
crank. Tighten the screw to secure. Rotate the Crank Handle clockwise a few turns to fully tension the net. See
Figure 8 & 9. Note: The center of the net should measure 34” from the top to the playing surface.
STEP 4:
STEP 5:
STEP 6:
STEP 7:
STEP 8: Tie a 2” knotted loop in one end of the Lacing Cord (Item #6).
Figure 5
Figure 6 Figure 7 Figure 8 Figure 9
STEP 9: Feed the other end of the lacing cord around the lacing rod, through the top grommet in the sideband of the net,
and then through the 2” knotted loop.
STEP 10: Threading the lacing cord through both grommets in the
headband of the net one way, and then back through each
grommet the other way, and through the top grommet in the
sideband of the net. Continue threading the lacing cord
around the lacing rod and through each grommet as shown in
Figure 10. Apply equal pressure as you lace the net to the
post.
STEP 11: Tie off the cord at the bottom of the post. Repeat on
the other post.
Figure 10

1. This Warranty is non-transferable and is expressly limited to the repair or
replacement of a defective Dominator, including any part thereof,
covered under this Warranty.
2. To make a claim under this Warranty, the Purchaser must first write the
Manufacturer at 405 N 880 W, Suite C, Lindon, UT 84042, to receive a
Return Authorization number and/or determine specific needs.
3. The Manufacturer reserves the right to examine photographs and/or
physical evidence of a Dominator claimed to be defective and to recover
said Dominator pursuant to the terms of this Warranty, prior to authoriza-
tion of a claim under this Warranty
4. Unless indicated otherwise by the Manufacturer, in order to determine
whether a requested repair is covered under this Warranty, the Dominator
must be shipped prepaid to the Manufacturer with a copy of the relevant
proof of purchase. The Manufacturer will not be responsible for any loss
or damage incurred in connection with the return of a Dominator or its
parts to Manufacturer under this Warranty. The manufacturer will examine
the Dominator so shipped and, in its sole and reasonable discretion, will
determine (1) whether this Warranty covers the Dominator and, if it does,
(2) whether the Dominator needs to be repaired or replaced. Any and all
dealer service charges, labor costs, shipping costs, insurance, travel
expenses and any other charges or costs involved in the removal,
installation or replacement of a defective Dominator, including, but not
limited to, any part thereof, covered under this Warranty, will be the sole
responsibility of the Purchaser and must be prepaid. Any Dominator,
including any part thereof, shipped to the Manufacturer “collect” will be
refused.
5. THIS WARRANTY IS VOID IF THE DOMINATOR HAS BEEN DAMAGED BY
ACCIDENT, UNREASONABLE USE AND/OR ABUSE, NEGLIGENCE, IMPROPER
SERVICE, IMPROPER INSTALLATION OR HANDLING, FAILURE TO FOLLOW
PROVIDED INSTRUCTIONS (INCLUDING WITHOUT LIMITATION USING THE
DOMINATOR AT PROHIBITED HEIGHT LEVELS), SHIPPING, VANDALISM,ACTS
OF GOD, ENVIRONMENTAL FACTORS, ALTERATION OF THE DOMINATOR, OR
ANY OTHER EVENTS BEYOND THE CONTROL OF THE MANUFATURER OR
OTHER CAUSES NOT ARISING OUT OF DEFECTS IN MATERIAL OR WORK-
MANSHIP.
6. USING THE DOMINATOR FOR OTHER THAN RESIDENTIAL USE WILL ALSO
VOID THIS WARRANTY.
7. HANGING FROM THE NET WILL ALSO VOID THIS WARRANTY: Nets are not
warranted for any defects other than workmanship. Torn back plates,
damaged springs, bent rings, damaged eyebolts and torn or distorted net
supports result from hanging are not warranted.
8. THIS WARRANTY DOES NOT COVER SCRATCHING OR SCUFFING OF THE
DOMINATOR THAT MAY RESULT FROM NORMAL USAGE.THIS WARRANTY
ALSO DOES NOT COVER RUSTING PARTS, FADING PAINT, CRACKS THAT DO
NOT AFFECT THE FUNCTIONALITY OF THE PRODUCT, OR OTHER DAMAGE
CAUSED BY WEATHER OR CLIMATE CONDITIONS OR EXPOSURE TO
CORROSIVES SUCH AS SALTS, PESTICIDES, ET
9. This warranty gives the Purchaser specific legal rights, and such
Purchaser may also have other rights which vary from state to state.
10. THIS WARRANTY IS GIVEN EXPRESSLY IN LIEU OF ALL OTHER EXPRESS
WARRANTIES. ANY IMPLIED WARRANTY ARISING OUT OF THE SALE OF THE
DOMINATOR, INCLUDING, BUT NOT LIMITED TO,THE IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS
LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
11. Some states do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to certain Purchasers.
12. THE REMEDY OF REPAIR OR REPLACEMENT STATED ABOVE SHALL BE THE
PURCHASER'S EXCLUSIVE REMEDY. THE MANUFACTURER DOES NOT
ASSUME OR AUTHORIZE ANY PERSON OR REPRESENTATIVE TO ASSUME ON
ITS BEHALF ANY OTHER LIABILITY IN CONNECTION WITH THE SALE OF A
DOMINATOR.THE MANUFACTURER SHALL NOT BE LIABLE FOR (A) ANY
DAMAGES OR EXPENSES THAT MAY OCCUR, INCLUDING, BUT NOT LIMITED
TO, INCIDENTAL, SPECIAL OR CONSEQUENTIAL DAMAGES, ARISING OUT OF
OR IN CONNECTION WITH THE DELIVERY, INSTALLATION, USE, PERFOR-
MANCE AND/OR REMOVAL OF THE DOMINATOR (INCLUDING, BUT NOT
LIMITED TO, DAMAGE TO CONCRETE OR THE PURCHASER’S YARD); (B) ANY
OTHER CLAIM ARISING FROM NEGLIGENCE, STRICT LIABILITY, OR BREACH
OF CONTRACT REGARDING THE DOMINATOR; OR © OTHER DAMAGES
WITH RESPECT TO ANY ECONOMIC LOSS, LOSS OF PROPERTY, LOSS OF
ENJOYMENT OF USE, COSTS OF INSTALLATION AND/OR REMOVAL, OR
OTHER CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR
IMPLIED WARRANTY COVERING THE DOMINATOR.
13. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not
apply to certain Purchasers.
14. While the Manufacturer has made attempts to ensure that the Domina-
tor is safe to use, freedom from injury cannot be guaranteed. The
Purchaser assumes all risk of injury resulting from the use of the
Dominator. All Dominators are sold subject to this condition, and no
representative of the Manufacturer may waive or change this policy.
SECTION 4: WARRANTIES & POLICIES
STANDARD LIMITED LIFETIME WARRANTY
Subject to the limitations set forth below, HomeSports (the “Manufacturer”) warrants to the original consumer purchaser (the
“Purchaser”) of the Dominator Heavy-Duty Inground Pickleball System (hereinafter referred to as the “Dominator”) that the
Dominator shall be free from material defects in parts and/or workmanship that impair the use of the Dominator for so long as
the Purchaser owns the Dominator.

STANDARD RETURN POLICY
1. The Purchaser may cancel an order before shipment and receive a full
refund of the amount paid. Orders are normally shipped within 48
business hours hours and are sometimes shipped the same day.
2. The Purchaser may return an order within 7 days of receipt of the
Dominator by the Purchaser to receive a partial refund. All returns are
subject to a 15% re-stocking fee. The Purchaser is responsible for
initial shipping fees upon return of the Dominator and any offer for
free shipping is surrendered upon return. Except as provided in
3. Manufacturer’s limited lifetime warranty, Manufacturer has sole
discretion to reject a request for cancellation or return.
4. The Dominator must be unused, in the original shipping boxes and
packaging, to be eligible for a refund.
5. Notwithstanding the above paragraphs, Purchaser shall have no right
to cancel or return custom-made products.
6. To make a return, the Purchaser must first contact the Manufacturer at
1-877-705-6556 to receive a Return Authorization number and/or
determine specific needs. YOU MUST HAVE A RETURN AUTHORIZATION
NUMBER OR YOUR RETURN WILL NOT BE PROCESSED.
7. The Purchaser must ship the Dominator to the Manufacturer with proof
of purchase. Any and all dealer service charges, labor costs, shipping
costs, insurance, travel expenses and any other charges or costs
involved in the return of a Dominator, will be the sole responsibility of
the Purchaser and must be prepaid. The Manufacturer will not be
responsible for any loss or damage incurred in connection with the
return of a Dominator or its parts to Manufacturer.Any Dominator,
including any part thereof, shipped to the Manufacturer “collect” will
be refused.
This Return Policy applies to the purchase of the Dominator® Heavy-Duty Inground Pickleball System (hereinafter
referred to as the “Dominator”) by the original consumer purchaser (“you” or the “Purchaser”) from Leap Innovations (the
“Manufacturer”).
1. Any offer for free shipping by the Manufacturer applies ONLY to
shipments within the domestic 48 continental United States. Please
contact us at 1-877-705-6556 for a shipping quote for deliveries to
Alaska, Hawaii, Canada, Mexico, or other locations outside of the
United States.
2. If the shipping address is changed during shipping, additional charges
may apply.
3. Shipping dates are approximate and Manufacturer does not guaran-
tee estimated delivery dates. Manufacturer is not liable under any
circumstances for any delay in shipment or delivery.
4. It is your responsibility to verify the delivery for correctness. You should
confirm the correct number of boxes has been delivered to you.
5. You should also carefully inspect all items prior to installing for
damage during transit and take photographs of the damage.
6. DO NOT REFUSE DELIVERY IF THE DOMINATOR, OR ANY PORTION
THEREOF, IS DAMAGED. Simply note the damage on the delivery
receipt and contact us at 801-768-4663 to receive a replacement
part.
7. If a certain part, such as the net, is damaged, you may still keep and
install the additional working parts while the replacement part is
being delivered.
8. Please note, if you live down a road or driveway that the delivery truck
cannot traverse, the delivery will not be completed. You may be
required to pick up the order from the nearest carrier terminal.
9. Any order returned to Manufacturer marked undeliverable or similar is
subject to a 15% restocking fee and any shipping charges incurred by
Manufacturer for the initial shipment to the Purchaser will be charged
to the Purchaser.
STANDARD SHIPPING POLICY
This Return Policy applies to the purchase of the Dominator® Heavy-Duty Inground Pickleball System (hereinafter
referred to as the “Dominator”) by the original consumer purchaser (“you” or the “Purchaser”) from Leap Innovations (the
“Manufacturer”).