DoubleSight DS-227PS User manual

Full Motion Dual Monitor Arm, Pole Mount
Model: DS-227PS
Quick Installation Guide
Please Review the entire Quick Installation Guide prior to installation.
If you have any questions regarding the compatibility of this Mount with your
Monitor please contact DoubleSight Customer Service prior to beginning the
installation. It may also be helpful to check your Monitor’s Manual for any
special mounting requirements outlined by the Monitor manufacturer.

Full Motion Dual Monitor Arm, Pole Mount
Model: DS-227PS
Please contact DoubleSight Displays Service and Support if you are missing any of the package
contents or need assistance.
Getting Started Model: DS-227PS
Instruction Manual
Images may differ from actual product.
Disclaimer
DoubleSight intended to make this manual completely all right. However, DoubleSight makes no claim that the
information comprised herein covers all conditions or details in connection with installation or use of this product.
The information comprised here is subject to change without notice or obligation of any kind. DoubleSight
assumes no responsibility for accuracy or adequacy of information comprised in this document.
A warning alerts you to the possibilities of personal injury or damage to equipment if you do not follow the
corresponding instructions. It is installer's responsibility to make sure all components are properly assembled and
installed using the instructions manual provided.
Using of improper screws size may damage your display. If spacers are required, be sure to use correct size of
screws. Proper screws used will easily and completely thread into the display mounting holes. Inadequate thread
engagement in the display may cause display falling.
It is installer’s responsibility to make sure the combined weight of all components does not exceed weight
capacity. Exceeding weight capacities can result in severe personal injury or damage to equipment. It is installer’s
responsibility to make sure the combined weight of all components does not exceed weight capacity of 9kg
(19.8lbs).
Allowing any part of your component cables to be caught between movable parts can result in serious personal
injury or damage to equipment.
The table installed must be strong and stable enough for supporting this LCD Arm and LCD

Read the following warning before installing
●Verify all parts are included. Do not install if the product if hardware is damaged. Not all
hardware included will be used.
●Please contact a qualified installer
●This product contain moving parts, Use with caution
●This product contains small item, keep these items away from children
●Do not exceed the maximum weight capacity for this product. Exceeding the weight capacity
can result in serious personal injury or damage to equipment!
●The table installed must be strong and stable enough for supporting this LCD Arm and LCD.
Please contact DoubleSight Displays Service and Support if you are missing any of the package
contents or need assistance.
Getting Started Model: DS-227PS
Specifications
Weight Capacity
19.50 lbs. per monitor
LCD Flat Panel Displays
Up to 27”
Maximum Extension
18.37 per monitor”
Pole Width
2.6”
Tilt adjustment
+/-90 degree
Display Pan Swing- Side to side
+/- 90 degree
Pivot (Desk / Display / Arm)
180°
Maximum Mounting Surface Thickness
2.95” (75mm)
VESA Compatibility
75x75mm and 100x100mm

Parts List
ASSEMBLY and INSTALLATION
INSPECT THE MOUNT BEFORE ASSEMBLY
Note: Read all assembly instructions before staring the installation process.
Please contact DoubleSight Displays Service and Support if you are missing any of the package
contents or need assistance.
Getting Started Model: DS-227PS
Carefully inspect the mount components to ensure all components are present.
Dual Arm Bracket
Qty.1
Arm Cover
Qty.2
Arm Cover Screw
Qty.2

Base Installation - Desk Clamp
Note: Do not over tighten the Handle. Stop immediately if you encounter any resistance.
1. Insert Left Cover and L Plate within the base of the Pole(3). (See Figure 1)
2. Fix the pin of L Plate Connection into the hole of L Plate. (See Figure 2)
Note: Other tools may be required depending on your method of installation.
Note: It is installer’s responsibility to make sure the desktop structure to which this product is attached can
support the combined weight of all compnents.
Assemble the Desk Clamp
Figure 1
Figure 2
INSTALLATION Model: DS-227PS

Install the Pole Assembly to Desk Edge
1. Place the Pole Assembly (3) over the open edge of the desk in the desired location. (See Figure 3).
Tighten the Clamp (4) by turning the handle until the Pole Assembly is securely in place. (See Figure 4)
2. To adjust the height of your monitor arm, loosen the Collar as shown. Position the Collar at desired height
and tighten with hand so the Collar assembly is firmly in place. (See Figure 5)
Figure 5
Figure 3 Figure 4
INSTALLATION Model: DS-227PS

Alternate Installation - Install the Pole Assembly through Desk’s Cable Guide
1. Insert Left Cover and L Plate within the base of the Pole (3). Fix the pin of L Plate Connection into the hole of L Plate. Insert
Left cover and L plate within the base of the pole. (See Figure 6).
2. Place L Plate through the desk hole. Then attach the pins of the L Plate Connection into the hole of L Plate. Turn and
tighten the Handle by hand to ensure that the Pressure Plate fully contacts to surface of the desk and it is secure in place as
shown. (See Figure 7)
Figure 7
Figure 6
INSTALLATION Model: DS-227PS

Attaching the Monitor Arms to the Pole Assembly
Figure 8
1. Attach the 2 LCD Arm (1) sections to the Dual Arm Bracket (2) as shown. (Figure 8)
2. Secure in place by inserting Arm Cover (8) and tightening with appropriate Arm Cover Screw(10). (Figure 8-10)
Figure 9
Figure 10
INSTALLATION Model: DS-227PS

Attaching the Monitor Arms to the Pole Assembly
Figure 11
3. Slip Dual Arm Bracket and Arms onto Pole Assembly as shown. (Figure 11-12)
4. Secure in place by tightening the Bracket screw as shown. (Figure 13)
Figure 12
Figure 13
INSTALLATION Model: DS-227PS

Installing your Monitor
Figure 14
Figure 15
Note: Using of improper screws size may damage your display. If spacers are required, be sure to use correct size of
screws. Proper screws used will easily and completely thread into the display mounting holes. Inadequate thread
engagement in the display may cause display falling.
Note: It is installer’s responsibility to make sure the combined weight of all components does not exceed weight capacity.
Exceeding weight capacities can result in severe personal injury or damage to equipment.
Attaching the Monitor to the VESA Bracket
Attaching the Monitors to the Dual Arms
1. Ensure VESA Bracket on the LCD Arm (1) is able to swivel and tilt easily. (Figure 14)
2. Hold Monitor flush to the VESA Bracket and secure with the provided Monitor Screws. (Figure 15).
3. Repeat with second Monitor.
INSTALLATION Model: DS-227PS

Figure 18
Figure 17
Figure 16
Using Cable Management Feature
1. Once you have connected your Monitor’s Cabling you can use the built in cable management to organize your
cabling. Locate the Cable Channels on the underside of the LCD Arm. Simply push cables into the channel, leaving
sufficient slack so as not to pull out cables when LCD Arm is moved. (Figure 15)
2. Secure the cables in place by snapping the Cable Covers (7) into the Cable Channels. (See Figure 17)
3. Use the Cable Clip (6) to secure cables to the base of the Pole. (See Figure 18)
INSTALLATION Model: DS-227PS

Figure 19
Figure 20
Adjusting your New LCD Arm to your preferences
Adjusting the Position on your Desk
Adjusting the Monitor Height
Adjusting the VESA Bracket Tension
1. Remove the Monitor and Dual Arm from the Pole prior to relocating the Pole. Simply lift off the Monitor and Dual
Arm and set aside on a level flat surface.
1. Depending on the weight of your monitor and your preferences, you may find it necessary to adjust the tension of
the VESA Bracket. You can adjust the Forward/Backward Tilt of the Bracket, as well as, the Left/Right Swing of the
Monitor. Using the 6mm Hex Allen Wrench (5) you can adjust the bolts to the desired tension. (See Figure 20)
1. Loosen the Collar and move Collar and Dual Arm Assembly up/down to the desired position. (See Figure 19)
Once your Monitor and LCD Arm are completely installed you may find it necessary to make adjustments to best suit your
needs.
2. Loosen the Clamp and relocate the Pole to the new positon and tighten in place.
3. Reinstall the Monitor and Dual Arm.
INSTALLATION Model: DS-227PS

Sales
DoubleSight Displays
:
:
:
Support
Tel : 877.896.5237
Tel : 888.897.8869
Website www.doublesight.com
CONTACT Model: DS-227PS
Table of contents
Other DoubleSight Rack & Stand manuals
Popular Rack & Stand manuals by other brands

Vivo
Vivo Sidekiix instruction manual

CHIEF
CHIEF FCA500 installation instructions

TYPE A
TYPE A 068-7148-8 Assembly instructions

ZyXEL Communications
ZyXEL Communications ANT-3218 - MOUNTING Configuration

Teledyne Lecroy
Teledyne Lecroy LabMaster 10Zi Assembly instructions

Konig & Meyer
Konig & Meyer 18950 Setup