DPS PHANTOM Cure Station User manual

High performance base treatment for alpine skis and snowboards.
Traitement de base haute performance pour skis alpins et snowboards.
Hochleistungs belagsbehandlung für alpinski und snowboards.
アルパインスキー、スノーボード用のハイパフォーマンスベーストリートメントです。
i
!
EN
Update: July 2020
Cure Station Formula
Formule De Cure
Konservierungsformel
CSF

PHANTOM Cure Station
Model:
Serial #:
Warning: Flammable liquid and vapor. Keep away from heat, hot surfaces, sparks, open ames and other ignition sources. Liquid can cause
eye and skin irritation. Use in a well ventilated area and wear protective gloves, eye and face protection. Wash hands thoroughly with soap
and clean water after handling, or immediately in case of contact with Phantom. Immediately wash eyes thoroughly with clean water or saline
solution in case of contact with Phantom. Do not eat, drink or smoke when using Phantom, and do not store food, drinks, tobacco or e-liquid
in or near the areas used to apply or cure Phantom. Do not ingest and do not smoke Phantom. If ingested, or through prolonged exposure,
may cause damage to the central nervous system, the kidneys and the heart. Do not use if you are pregnant or have breathing difculties. Do
not mix with other products of any kind. Clean up spills immediately. KEEP OUT OF REACH OF CHILDREN AND PETS. It is safer for you to
have the Phantom application process performed by a qualied professional. Once cured on a ski or snowboard, this is an inert material that
is non-hazardous and emits no vapors.
In the event of a medical or chemical emergency contact ChemTel, North America 1-800-255-3924 or Worldwide [phone]. All other
non-emergency inquiries about the product should be directed to DPS Skis: [phone] or [email protected].
Attention: Liquide et vapeurs très inammables. Tenir à l’écart de la chaleur, des surfaces chaudes, des étincelles, des ammes nues et de
toute autre source d’inammation. Le liquide peut provoquer une irritation des yeux et de la peau. Utiliser dans un endroit bien ventilé et
porter des gants de protection, un équipement de protection des yeux et du visage. Se laver soigneusement les mains avec du savon et
de l’eau propre après utilisation, ou immédiatement en cas de contact avec le produit Phantom. Laver immédiatement et abondamment les
yeux avec de l’eau propre ou une solution saline en cas de contact avec le produit Phantom. Ne pas manger, boire ou fumer en manipulant
le produit Phantom, ne pas stocker d’aliments ni de boissons, tabac ou e-liquide dans ou à proximité des zones utilisées pour appliquer
ou faire sécher le produit Phantom. Ne pas ingérer et ne pas fumer le produit Phantom. En cas d’ingestion, ou d’exposition prolongée,
peut causer des dommages au sytème nerveux central, aux reins et au cœur. Ne pas utiliser si vous êtes enceinte ou avez des difcultés
respiratoires. Ne pas mélanger avec un quelconque autre produit. Nettoyer immédiatement tout liquide renversé. TENIR HORS DE PORTEE
DES ENFANTS ET DES ANIMAUX DE COMPAGNIE. Pour votre santé, il est plus sûr de faire réaliser le processus d’application Phantom
par un professionnel qualié. Une fois durci sur un ski ou un snowboard, il s’agit d’un matériau inerte non dangereux qui ne dégage aucune
vapeur.
En cas d’urgence médicale ou chimique, contactez ChemTel, au 1-800-255-3924 en Amérique du Nord ou dans le monde entier au +1-813-
248-0585. Toutes les autres questions non urgentes concernant le produit doivent être adressées à DPS Skis au [phone] ou à
[email protected].
Warnung: Flüssigkeit und Dampf entzündbar. Von Hitze, heißen Oberächen, Funken, offenen Flammen und anderen Zündquellen fernhalten.
Flüssigkeit kann Augen- und Hautreizungen verursachen. In einem gut gelüfteten Bereich verwenden und Schutzhandschuhe sowie Augen-
und Gesichtsschutz tragen. Waschen Sie sich nach der Handhabung oder bei Kontakt mit Phantom sofort die Hände mit Seife und klarem
Wasser. Bei Kontakt mit Phantom sofort die Augen gründlich mit klarem Wasser oder Kochsalzlösung waschen. Bei der Verwendung von
Phantom nicht essen, trinken oder rauchen und keine Lebensmittel, Getränke, Tabak oder E-Liquid in oder in der Nähe von Phantom
lagern. Nicht einnehmen und kein Phantom rauchen. Bei Verschlucken oder bei längerer Exposition können das zentrale Nervensystem, die
Nieren und das Herz beschädigt werden. Nicht verwenden, wenn Sie schwanger sind oder Atembeschwerden haben. Mischen Sie nicht mit
anderen Produkten oder irgendeiner Art. Verschüttungen sofort aufräumen. NICHT REACH ODER KINDER UND TIERE AUFBEWAHREN.
Es ist sicherer für Sie, das Phantom-Antragsverfahren von einem qualizierten Fachmann durchführen zu lassen. Einmal auf einem Ski oder
Snowboard ist dies ein inertes Material, das ungefährlich ist und keine Dämpfe abgibt.
Im Falle eines medizinischen oder chemischen Notfalls wenden Sie sich an ChemTel, North America 1-800-255-3924 oder Worldwide +1-
813-248-0585. Alle anderen Anfragen zu Produkten, die nicht für Notfälle bestimmt sind, richten Sie bitte an DPS Skis: [phone]
oder [email protected].
引火性液体および蒸気です。熱、高温の表面、火花、炎、その他の発火源から遠ざけてください。液体は眼や皮膚刺激を引き起こすことがあります。換
気の良い場所で使用し、保護手袋、眼および顔面保護具を着用してください。取扱い後は直ちに石鹸と水で清潔に洗い流すか、ファントムと接触した
場合はすぐに手を洗ってください。ファントムが目に入った場合は、直ちに清浄な水または生理食塩水で十分に洗浄してください。ファントムを使用
するときには、飲食や喫煙をしないでください。また、ファントムの施工に使用する区域やその周辺には、食べ物、飲み物、タバコ、e-液体などを保管
しないでください。Phantomを体内に摂取したり吸ったりしないでください。摂取した場合、または長期間触れていた場合、中枢神経系、腎臓および
心臓の損傷を引き起こす可能性があります。妊娠しているか、呼吸困難がある場合は使用しないでください。いかなる種類の他の製品とも混合しな
いでください。こぼれた液体は直ちに清掃してください。子供やペットの手の届かないところに保管してください。ファントムの施工取扱いのプロセス
を訓練された専門家が実行することが安全です。スキーやスノーボードで一度硬化すると、これは危険ではなく、蒸気を放出しない不活性材料です。
医学的または化学的な緊急事態が発生した場合、ケムテル、北米1-800-255-3924または ワールドワイド+1-813-248-0585に連絡してください。製品
に関するその他の緊急以 外の問い合わせはすべて、DPS Skis [phone]または [email protected])にお問い合わせください。

EN
OVERVIEW
PHANTOM Cure Station™ and PHANTOM™ are designed to work together in a shop environment to provide consistent
and rapid UV cure for skis and snowboards. The formula has been specically designed and tested with the temperature
and UV concentration and combinations of wavelengths created by this equipment. No other processes other than the
cure station described or in the natural outdoor strong sunlight cure instructions should be attempted.
Please read the PHANTOM bulk application instructions and warnings before beginning.
Minimum recommended shop temperature is 58°F/15°C for a reasonable 15-30 minute cure station preheat. Longer
preheat may be required at lower starting ambient temperatures.
Refer to Storage and Handling instructions (pg 12) for correct care of your PHANTOM CSF.
Each bulk bottle contains 250ml of PHANTOM liquid.
Disposal: If entire contents of individual packets or bulk containers are not used up, remaining liquid can be poured into
absorbent cloth or paper and disposed of once entirely dry.
Please contact DPS Skis at +1.801.413.1737 or [email protected] if you have any troubles or questions
regarding the PHANTOM Cure Station™ or PHANTOM™.
Manufacturer:
Drake Powderworks, Inc.
DBA: DPS Skis
647 South 600 West
Salt Lake City, UT 84101
USA
Phone: [phone]
Email: [email protected]
Website: www.phantomglide.com
Voltage: 110 VAC
Nominal Current: 6 A
Frequency: 60 Hz
Made in: Salt Lake City, Utah, U.S.A.
Voltage: 220 VAC
Nominal Current: 3 A
Frequency: 50 Hz
Made in: Salt Lake City, Utah, U.S.A.
Caution: To identify general caution when using the product.
Used for less serious health hazards like skin irritation.
Flammable
Denitions of symbols:

EN
Caution:
•Two Person Lift Required. PHANTOM Cure Station is a long, heavy object.
• Hot Surface. Do not touch the internal heating unit during or after operation.
• Disconnect PHANTOM Cure Station from power source when servicing.
Cleaning Information
Over time moisture or evaporative residue may build up inside of the station. Wear appropriate gloves and wipe down
rst with a damp absorbent cloth or paper and then give a nal wipe down with a dry absorbent cloth or paper.
IMPORTANT Power Cable Information
Please, ensure that your PHANTOM Cure Station is electrically rated to operate with the AC power available in your
location. North America voltage: 110 VAC. Europe and Japan voltage: 220 VAC.
• Only use the power cable that was provided with your PHANTOM Cure Station.
• Do not plug the equipment power cable into an electrical outlet if the power cable is damaged.
• To prevent electric shock, plug the equipment power cable into properly grounded electrical outlets. If the equip-
ment is provided with a 3-prong power cable, do not use adapter plugs that bypass the grounding feature, or remove
the grounding feature from the plug or adapter.
• Connect the power cable to a grounded electrical outlet only.
• If you use an extension power cable, ensure that the total ampere rating of the products plugged in to the extension
power cable does not exceed the ampere rating of the extension cable.
• If you must use an extension cable or power strip, ensure the extension cable or power strip is connected to a wall
power outlet and not to another extension cable or power strip. The extension cable or power strip must be designed
for grounded plugs and plugged into a grounded wall outlet.
• If you are using a multiple-outlet power strip, use caution when plugging the power cable into the power strip.
Some power strips may allow you to insert a plug incorrectly. Incorrect insertion of the power plug could result in
permanent damage to your equipment, as well as risk of electric shock and/or re. Ensure that the ground prong of
the power plug is inserted into the mating ground contact of the power strip.
• Be sure to grasp the plug, not the cable, when disconnecting equipment from an electric socket.

EN
BC D
G
A
E
Power Cord Inlet/Main Power Switch
Preheat
Start
Cancel
Saw Horse
Door Limit Switch
OPERATION

EN
Attach the supplied power cord to A.
NOTE: If a rmware update is required, you will be sent an email with a zipped rmware code. You then install
the cord into the slot in the back left side of the display screen (B) and follow the emailed instructions to install.
To switch between Fahrenheit and Celsius, at initial power up press “cancel” to toggle between F or C.
Pushing cancel at initial power up will display current installed rmware version, i.e. 2.49 F.
The door limit switch (G) may need to be adjusted in/out to ensure switch activation, while not creating a
signicant gap in the door seal. Do this by adjusting the order of the nuts holding the switch onto the metal tab.
If any issues persist please contact us.
90º
INITIAL SET UP
Install the 4 custom UV light bulbs into the light clips. Insert with pins vertical and rotate 90° until “click”.
A. Best if done by two people to securely insert each end to the light clips.
B. UV light is directional. Make sure the bulb logo faces down once installed.
STEP 1
STEP 2
STEP 3

EN
HOW TO OPERATE:
Turn on the main power switch on the back left (A).
Triple display button (Cure Station version 2 and up):
a. With the door closed, press Preheat once. Both the heater and fan and the 4 UV lights should be on
during Preheat.
i. After temperature is reached, the station will maintain this temperature for a maximum of two
hours and will automatically shut off if there is no activity.
b. Insert the gear base side up centered under the lights, close the door, and press the Start button.
The cure cycle timer will only be initiated at this point if ‘Ready to Cure’ is displayed. Have the
door open for minimum time to retain heat and ensure efcient curing.
c. To cancel at anytime during Preheat, or a cure cycle, press Cancel.
NOTE:
• Initial preheat can take up to 30 minutes depending on ambient temperatures.
• The station is not designed for shop temperature below 58°F/14°C or may take longer to preheat.
• The rst few heat cycles may have a slight burning odor while the heating elements clean off any
manufacturing oils or dust.
STEP 1
STEP 2

EN
Over 180cm = 6.9ml per ski
170-180cm = 6.1ml per ski
155-170cm = 5.3ml per ski
Under 155cm = 4.5 ml per ski
150-170cm = 12.2ml a board
130-150cm = 10.6ml a board
Under 155cm = 9ml a board
IMPORTANT: PHANTOM is gravity fed and penetrates through
the thickness of the base. Think of it like pouring water on a dry
sponge. It requires a specic volume and time for the bases to
fully absorb PHANTOM.
HOW TO APPLY BULK PHANTOM:
*
*
*
STEP 1
Clean the base either by a fresh stone-grind or a thorough base
cleaning.
A base grind is highly recommended if the base is at all abraded/
oxidised and/or has bad structure and damage, and is critical to
ensure good PHANTOM performance.
If the bases are in good shape use a citrus base cleaner (solvent-
based cleaners are not recommended) to remove old wax and dirt
and clean the base. Apply liberally. Spread with a paper towel until
base is fully covered and clean. Wipe dry with a clean micro-bre
towel, allowing full evaporation of base cleaner afterwards.
If base is particularly dirty brush it out, and then repeat base
cleaning process.
XX
!!
A
C
IMPORTANT: PHANTOM should be at ambient room temperature (65°F - 85°F / 18°C - 30°C).
With the lid closed, thoroughly shake the bulk bottle container before each use. And close the lid after each use. Meter out
the correct amount of PHANTOM per the size chart by applying as a line down the center of the ski/board. Applying light
pressure with non-absorbent pad, spread evenly between the contact points, working from the centre of the ski out to the
edges (to minimise mess and clean-up later). Spread PHANTOM out to tips and tails, trying to minimise run off. Wipe off any
excess PHANTOM that spills over onto the top sheet.
STEP 2
NOTE: PHANTOM 2.0 from 2018 is a two-part process requiring a Part A cure and a Part B cure.
PHANTOM CSF from 2019 is offered in bulk bottles for shops and demo needs and is a one-part process with a single
cure.

EN
BC D
G
A
E
15
min
!Place ski(s)/snowboard on a at surface for a 15 minute soak period.
After the soak period, wipe down ski(s)/snowboard vigorously with a
clean paper towel. The aim should be for the ski to have a polished
sheen, with no pools of excess PHANTOM. This wipe down is key for
getting complete and timely cures in the Cure Station. Also clean any
excess drippings that dripped onto the top sheet and edges with a
damp rag or alcohol wipe. PHANTOM can leave a stain on top sheets
if left on. A WD-40 type cleaner/degreaser can help remove a stain. Or
wiping down with a very hot wet rag.
Note: Bases should be treated at a minimum shop temperature of 58°F/15°C. For optimum results bases should be at 75 -
100 F prior to applying PHANTOM.
STEP 3
With any binding brakes securely strapped at, or snowboard bindings off, insert into the cure station on the supplied stands
with tips facing the heater (to improve cure times) and close the door. Minimise time the door is open to retain internal Cure
Station heat.
A. UV lights will NOT come on unless the door is closed and the limit switch in the upper left corner
is activated.
B. If the internal temperature is below a threshold the cure station may go through a pre-heat period
before the timer begins the countdown.
Once the rst cycle is done the base should be dry with light PHANTOM residue. If wetness exists, wipe off with a paper
towel and continue curing for another 5-10 minutes.
STEP 4

EN
Firstly make sure that ski is completely dry. If any wetness exists, continue to cure in the Cure Station and do not proceed
further in the process. If you are unsure if a patch is wet, you may test it by swiping the area with a rubber glove and
seeing if any oily residue is left on the glove.
Wear appropriate eyewear and mask to avoid ying particles. Using a nylon roto brush, vigorously roto the base(s) from tip
to tail until base looks its natural color with no visible white (PHANTOM).
Spray water over the entire ski (we recommend a spray bottle of water for this). Wipe off with a clean microber until dry.
STEP 4 STEP 5
On a dry base repeat Step 2 - 5 with Part B.
Note that when initially spreading PHANTOM Part B over the base, it may pill/bead up. If this occurs, continue to spread/
massage the PHANTOM Part B into the base until you see an even distribution.
Label on the base as Part B if you desire.
NOTE: For sequential applications, while one pair is curing, another pair should be in the
15-minute soak cycle.
STEP 4 STEP 6(for two part PHANTOM2.0 only)

EN
PERMANENT WAXLESS GLIDE
A PHANTOMed base will continue to have consistent and fast glide, for as long as the base is kept in good condition. In
practice, this means that some maintenance is required at regular intervals.
When the bases begin to look dry/white, this is a sign that abrasion has formed micro-hairs on the base. These can be
managed through polishing, with either a felt roto brush, or a soft polishing pad. Dirt and grease also need to be cleaned
off regularly. Use a citrus base cleaner, and follow up with polishing.
If the structure of the bases becomes damaged or severely abraded, a base grind is recommended. A base grind should
always be followed by polishing.
Following the nishing/brushing process in Step 5 (or 6), polish the bases with a felt roto brush. Do 2 passes in both
directions (i.e. tip to tail, and then tail to tip). Take care to move the brush quickly along the bases in order to not cause
friction burn. At this point, the ideal base appearance is matte black.
Do a nal top sheet clean using wd-40 and a paper towel, rubbing vigorously. Then clean with rubbing alcohol. Once
alcohol is dry if you cannot see any PHANTOM stains move on to cleaning side wall and edges. Or if it seems further
cleaning is needed use a wire brush lightly in a circular motion with wd-40 until the stains are gone. Check the stains are
fully gone using rubbing alcohol once again.
Wipe the whole ski off. Visually inspect to make sure that everything looks clean and correct.
Place PHANTOM sticker on each ski.
STEP
STEP
4
4
STEP
STEP
7
8

EN
Storage and Handling
Opened bottles should be kept at less than 85F (30C). Vigorously shake before each use, and keep the lids locked closed
after each use. Bottles should be used within 9 months, otherwise please contact DPS for situation specic advice.
For long-term storage (i.e. during the off season), the following steps are meant as best practice:
1. Gently squeeze the air from the bottle and close tightly (leaving compressed).
2. Double bag the bottle(s) in ziplock bags or other similar freezer bags. the packaged bottles in a freezer (or fridge) and
leave long term.
3. Remove bottles from cold storage a day before intended use and let sit out until they have reached room temperature.
4. Wait until the bottles have warmed up before “unsqueezing” them - this will make the process much easier. Inspect
consistency.
Please Note: If you notice the consistency of the Phantom has thickened considerably to a gel or other similar substance,
notify us immediately and avoid use on skis.

EN
For local European 24/7 spill or accidents service in specic countries, call your regional poison control center,
or the global service listed which has our SDS on le and product information.
Best Practices:
• Store unopened bulk bottles over time in a cool dry place.
• Completely nish a bulk bottle within 9 months of opening.
• Always close the lid after each application.
• Avoid direct UV light, except for curing inside the box.
• Use protective gloves to avoid contact with skin.
• PHANTOM is harmful if ingested. Clean up spills and keep away from children and pets.
• Wear protective eyewear and mask while rotobrushing.
• Apply in a well ventilated area
• Store test tubes upside down on top of a paper towel/absorbent cloth
Servicing Items (available by contacting DPS):
• Fuse 10A 250VAC 5X20MM
• Power Cord 110v Type B - IEC 320 connection (NA/JP)
• Power Cord 220v Type F - IEC 320 connection (Europe)
• Power Cord 220v Type J - IEC 320 connection (Switzerland)
• Power Cord 220v Type G - IEC 320 connection (UK)
• Power Cord 220v Type I - IEC 320 connection (Southern Hemisphere)
• USB cord A Male × B Male 3’
• PHANTOM UV Bulbs
• Replacement Limit Switch (G)
• Extra gloves, masks, squeegees, available upon request.
In the event of a medical or chemical emergency contact ChemTel, North America
1-800-255-3924 or Worldwide [phone]. All other non-emergency inquiries about the
product should be directed to DPS Skis: [phone] or [email protected].

EN
PHANTOM CSF Instructions Troubleshooting:
Why won’t the cure station turn on?
• Check the exterior plug connection.
• Check the fuse box in the plug power box.
The UV lights will not turn on?
• Check the limit switch connection is securely connecting to the door. You can adjust the contact
pressure by adjusting the positioning nuts.
• Inspect wiring of the limit switch for proper connection.
• Move a functional light from another slot into the slot where a non-working light is. This will check if the
issue is with the UV light itself, or with the light clips.
• Order NEW UV lights through customer service at [email protected]. Light specications
are specic to the PHANTOM Cure Station and no other lights should be used other than DPS provided.
Why is the wipe down ‘chunky’?
• The PHANTOM formula is starting to gel, this can occur in some environmental conditions. Wipe off all
PHANTOM residue, and reduce the soak period to 10 minutes for future applications.
What do I do if the bases are still wet after 20 minutes curing in the cure station?
• Take the skis/board out, and using a fresh paper towel wipe down any wet areas. Place the skis/board
back in the Cure Station for another 5 - 10 minutes, or until the base(s) are 100 % dry.
• For future applications more vigorously wipe off the excess PHANTOM residue (post soak and pre cure)
leaving no pooling.
What do I do if the Cure Station won’t reach ‘Ready to Cure’ temperature?
• Check all 4 x UV lights are functional.
• Check the fan is running, you should be able to hear a ‘whirr’.
• Check the seal between the main body of the box and the door is tight.
• Be mindful of how often or how long you open the door.
• Start the preheat cycle before prep work on the skis.
• Make sure your ambient shop temperature is within reason.
The bases look a little white after curing and brushing?
• The base could be heavily oxidized or abrasion damaged with micro-hairs. Polishing with bertex or
other abrasives can help this, or the bases need a new stone grind to remove the damaged surface.
• You may not have brushed enough of the PHANTOM topical residue off. Continue brushing, followed by
aggressive polishing with ner brushes or bertex along with water.

EN
HOW TO UPDATE PHANTOM CURE STATION FIRMWARE - MAC
Step 1: Download Arduino IDE software for Mac OS X https://www.arduino.cc/en/Main/Software.
• You can skip the donation by selecting just download at the bottom of the page. Once you have downloaded
Arduino IDE, open the zip le and then move the Arduino app to your Apps folder.
Step 2: Download HexUploader (http://paulkaplan.me/HexUploader/).
Programs: Mac
Updating the Firmware
Step 3: Download the latest version of the Cure Station rmware (will be sent in an email or a web-link).
Step 4: With the Cure Station power off and main power cord unplugged, insert the USB curved side facing up
into the inside back left port of the display box, and plug the other end into your computer.
Step 5: Open HexUploader on your computer
• Make sure the Arduino Type selected is Uno - ATmega 328p.
• Select the Serial Port “usbmodemXXXX”
• Make sure the Baud Rate is 115200.
• Click “Upload a Hex File” and select the latest version of the of the rmware you were sent.
• Within seconds the text box on the right side will conrm whether the upload was successful.
• Unplug the USB cord from the Cure Station. Power on the unit.

EN
HOW TO UPDATE PHANTOM CURE STATION FIRMWARE - PC
PC Download Instructions
• Go to ‘PC Application Downloads’ in the Google Drive ‘Cure Station Firmware Update’ folder
• Download the XLoader.zip
• Exctract all les from the .zip
• Inside of the XLoader Folder click on the XLoader application
How to use XLoader to load a new version of PHANTOM Cure Station Firmware
• The left screenshot shows the window that Xloader displays when it starts.
• Go back to the ‘Cure Station Firmware Update’ folder and nd the ‘Firmware Updates’ within.
• Determine if you have a 3 button or 1 button Cure Station
• Download the correlating .hex le in the 3 button or 1 button folder
• Click the ‘...’ in the CLoader application and nd the .hex le in your downloads
• Select the le
• Be sure that all settings are set as shown below (Device: UnoATmega328, Baud rate: 115200)
• The COM port is specic to your unit. The dropdown will only list your COM#
• Press the “Upload” button.
• When the .hex le has been loaded into the Arduino/X-controller the right screenshot will show the size of
the le uploaded, or an error message if the upload fails.

EN
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Fuse Ratings and Characteristics
Miniature Fuse, 5 x 20 mm, Time-Lag T, L, 250 VAC
Description
IEC Standard Fuse
L = Low Breaking Capacity (Glass Tube)
Applications
Primary Protection in Equipment
Technical Data
Rated Voltage:
Rated current:
Breaking Capacity:
Characteristic:
Admissible Ambient Air Temp:
Climatic Category:
Material: Tube
Material: Endcaps
Unit Weight:
Storage Conditions:
250VAC
0.05 - 20A
35A - 200A
Time-Lag T
-55°C to 125°C
55/125/21 acc. to IEC 60068-1
Glass
Nickel-Plated Copper Alloy
1g
0°C to 60°C, max. 70% r.h.