DR Pro 475 Quick start guide

Serial No.
Order No.
Read and understand this manual and all instructions before operating or servicing this DR SELF-FEEDING WOOD CHIPPER.
DR Power Equipment
Toll-free phone: 1-800-DR-OWNER (376-9637)
Website: www.DRpower.com
DR®SELF-FEEDING WOOD CHIPPER
SAFETY & OPERATING INSTRUCTIONS
Models:
Pro 475
Pro XL 575

2DR® SELF-FEEDING WOOD CHIPPER

CONTACT US AT www.DRpower.com 3
This indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
Table of Contents
Chapter 1: General Safety Rules....................................................................................................................... 4
Chapter 2: Setting Up the DR SELF-FEEDING WOOD CHIPPER.................................................................. 9
Chapter 3: Operating Your DR SELF-FEEDING WOOD CHIPPER .............................................................. 17
Chapter 4: Maintaining the DR SELF-FEEDING WOOD CHIPPER ............................................................. 23
Chapter 5: Troubleshooting ........................................................................................................................... 37
Chapter 6: Parts List and Schematic Diagrams ............................................................................................ 40
Conventions used in this manual
Serial Number and Order Number
A Serial Number is used to identify your machine and is located on the Serial Number Label on your machine. An Order Number
is used to check and maintain your order history and is located on your packing slip. For your convenience and ready reference,
enter the Serial Number and Order Number in the space provided on the front cover of this manual.
Additional Information and Potential Changes
DR Power Equipment reserves the right to discontinue, change, and improve its products at any time without notice or obligation
to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described
within this manual may be optional. Some illustrations may not be applicable to your machine.
California Proposition 65
This information is important in the proper use of your machine. Failure to follow this instruction could result in damage to
your machine or property.
This indicates a hazardous situation, which, if not avoided, could result in minor or moderate injury.
This indicates a hazardous situation, which, if not followed, will result in death or serious injury.

4DR® SELF-FEEDING WOOD CHIPPER
10000042639
10000042667
10000043343
10000042683
10000043333
Chapter 1: General Safety Rules
Labels
Your DR SELF-FEEDING WOOD CHIPPER carries prominent labels as reminders for its proper and safe use. Shown below are
copies of all the safety and operation labels that appear on the equipment. Take a moment to study them and make a note of their
location on your DR SELF-FEEDING WOOD CHIPPER as you assemble and before you operate the unit. Replace damaged or
missing safety and operation labels immediately.
Read this safety & operating Instructions manual before you use the DR®Chipper. Become familiar with the operation and
service recommendations to ensure the best performance from your machine. If you have any questions or need assistance,
please contact us at www.DRpower.com or call toll-free 1-800-DR-OWNER (376-9637) and one of our Technical Support
Representatives will be happy to help you.

CONTACT US AT www.DRpower.com 5
Pictogram Descriptions
Do not exceed 45 mph while towing
a chipper that is equipped with a
Road Tow Kit.
Read this safety &operating
Instructions manual before you use
the machine. Become familiar with
the operation and service
recommendations to ensure the
best performance.
Keep bystanders 50 feet away from
your work area at all times. Wood
chips exit the chipper at great speeds.
To be safe, do not operate the machine
near small children or pets, and never
allow children to operate the chipper.
Stop the engine when another person
or pet approaches.
Use ear protectors or ear plugs
rated for at least 20 dba to
protect your hearing.
Always wear protective goggles or
safety glasses with side shields while
chipping to protect your eyes from
possible thrown debris.
Do Not Exceed 10 mph while towing
a chipper equipped with a Yard Tow
Kit. Never tow the Yard-Tow model
over roads.
This label indicates proximity to
machine openings with rotating blades
inside.
SERIOUS INJURY OR DEATH will occur
if hands, feet, or any part of your body
are placed in the chipper hopper,
discharge opening, or near or under any
moving part while the machine is
running.
Never run without guards in place.
Never reach into feed hoppers,
discharge opening, or maintenance
openings. SERIOUS INJURY OR
DEATH may occur.
Machine may discharge wood chips and
debris at great speeds. Keep area of
discharge clear of people, animals,
buildings, glass, or anything else that will
obstruct clear discharge, cause injury, or
damage. Wind can also change
discharge direction, so be aware.

6DR® SELF-FEEDING WOOD CHIPPER
Protecting Yourself and Those Around You
Safety for Children and Pets
Tragic accidents can occur if the operator is not alert to the presence of children and pets. Children are often attracted to the
machine and the chipping activity. Never assume that children will remain where you last saw them. Always follow these
precautions:
•Keep children and pets at least 50 feet from the working area and under the watchful care of a responsible adult.
•Be alert and turn the machine off if children or pets enter the work area.
•Never allow children to operate the DR SELF-FEEDING WOOD CHIPPER.
This is a high-powered machine, with moving parts operating with high energy at high speeds. You must operate the machine
safely. Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area. Always take the
following precautions when using this machine:
•Always wear protective goggles or safety glasses with side shields while chipping to protect your eyes from possible thrown
debris.
•Avoid wearing loose clothing or jewelry, which can catch on moving parts or the material fed into the chipper hopper.
•We recommend wearing gloves while chipping. Be sure your gloves fit properly and do not have loose cuffs or drawstrings.
•Wear shoes with non-slip treads when using your chipper. If you have safety shoes, we recommend wearing them. Do not
use the machine while barefoot or wearing open sandals.
•Wear long pants while operating the DR SELF-FEEDING WOOD CHIPPER.
•Use ear protectors or ear plugs rated for at least 20 dba to protect your hearing.
•Never allow people who are unfamiliar with these instructions to use the chipper. Allow only responsible individuals who are
familiar with these rules of safe operation to use your machine.
•Never place your hands, feet, or any part of your body in the chipper hopper, discharge opening, or near or under any moving
part while the machine is running. Keep area of discharge clear of people, animals, buildings, glass, or anything else that will
obstruct clear discharge, cause injury, or damage. Wind can also change discharge direction, so be aware. If it becomes
necessary to push material into the chipper hopper, use a small diameter stick, not your hands.
•Keep bystanders 50 feet away from your work area at all times. Wood chips exit the chipper at great speeds. To be safe, do
not operate the machine near small children or pets, and never allow children to operate the chipper. Stop the engine when
another person or pet approaches.
•Never use the machine without ensuring that all guards and shields are in place, including the chipper hopper, discharge
chute and blowback shield.
•Always operate the machine from the operator zone (see chapter 3). Never pass or stand on the discharge side of the
machine when the engine is running or the flywheel is turning.
•Never try to pick up, move, or transport the machine while the engine is running or the flywheel is turning.
•Clear the area of objects such as wire and rope, etc. Inserting these objects into the chipper hopper could damage the
flywheel and/or cause injury.
•Never, under any conditions, remove, bend, cut, fit, weld, or otherwise alter standard parts on the DR SELF-FEEDING WOOD
CHIPPER. This includes all shields and guards. Modifications to your machine could cause personal injuries and property
damage and will void your warranty.

CONTACT US AT www.DRpower.com 7
•Before towing, be certain the DR SELF-FEEDING WOOD CHIPPER is correctly and securely attached to the towing vehicle and
the safety chains are in place. Leave slack in the chains to allow for turning.
•Never allow anyone to ride on the DR SELF-FEEDING WOOD CHIPPER.
•Never transport anything on the machine.
•Obey local, state, and federal regulations when you tow the chipper on public roads and highways.
•Some states may require the machine to be registered with the state department of motor vehicles.
•Allow for added length in driving situations, e.g., when turning, parking, and crossing intersections.
•Adjust your towing speed for terrain and conditions. Do not exceed 45 mph while towing the chipper.
•Towing the machine can affect handling of the tow vehicle:
−The chipper might track at an angle to the tow vehicle.
−The machine can turn tighter than the tow vehicle.
−Never back up the tow vehicle with the chipper attached. The machine can jackknife, causing damage to itself and/or the
tow vehicle.
•Long distance towing is not recommended. The DR SELF-FEEDING WOOD CHIPPER does not have springs to absorb road
shock and will tend to bounce on rough roads. Extended towing can cause unnecessary wear.
Safety with Gasoline - Powered Machines
Road Towing Safety (For Road-Tow Models Only)
Gasoline is a highly flammable liquid. Gasoline also gives off flammable vapor that can be easily ignited and cause a fire or
explosion. Never overlook the hazards of gasoline. Always follow these precautions:
•Never run the engine in an enclosed area or without proper ventilation as the exhaust from the engine contains carbon
monoxide, which is an odorless, tasteless, and deadly poisonous gas.
•Store all fuel and oil in containers specifically designed and approved for this purpose and keep away from heat and open
flame, and out of the reach of children.
•Replace rubber fuel lines and grommets when worn or damaged and after 5 years of use.
•Fill the gasoline tank outdoors with the engine off and allow the engine to cool completely. Don't handle gasoline if you or
anyone nearby is smoking, or if you're near anything that could cause it to ignite or explode. Reinstall the fuel tank Cap and
fuel container cap securely.
•If you spill gasoline, do not attempt to start the engine. Move the machine away from the area of the spill and avoid creating
any source of ignition until the gas vapors have dissipated. Wipe up any spilled fuel to prevent a fire hazard and properly
dispose of the waste.
•Allow the engine to cool completely before storing the DR SELF-FEEDING WOOD CHIPPER in any enclosure. Never store the
machine with gas in the tank or a fuel container, near an open flame or spark such as a water heater, space heater, clothes
dryer or furnace.
•Never make adjustments or repairs with the engine running. Shut down the engine, disconnect the spark plug wire, keeping it
away from the spark plug to prevent accidental starting, wait 5 minutes before making adjustments or repairs.
•Never tamper with the engine’s governor setting. The governor controls the maximum safe operation speed and protects the
engine. Over-speeding the engine is dangerous and will cause damage to the engine and to the other moving parts of the
machine. If required, see your authorized dealer for engine governor adjustments.
•Keep your hands and combustible substances away from the engine when it is hot and clean the engine area after each use.
•To reduce fire hazard, keep the engine cooling fins and muffler area free of debris build-up such as leaves, grass, oil, grease or
any other combustible material.
•Never cover the machine while the muffler is still hot.
•Do not operate the engine with the air cleaner or the carburetor air intake cover removed, except for adjustment. Removal of
such parts could create a fire hazard.
•Do not use flammable solutions to clean the air filter.
•The muffler and engine become very hot and can cause a severe burn; do not touch.

8DR® SELF-FEEDING WOOD CHIPPER
General Safety
A Note to All Users
Under California law, and the laws of some other states, you are not permitted to operate an internal combustion engine using
hydrocarbon fuels without an engine spark arrester. This also applies to operation on US Forest Lands. All DR SELF-FEEDING
WOOD CHIPPERS shipped to California, New Mexico and Washington State are provided with spark arresters. Failure of the
owner or operator to maintain this equipment in compliance with state regulations is a misdemeanor under California law and
may be in violation of other state and/or federal regulations. Contact your local fire marshal or forest service for specific
information in your area.
No list of warnings and cautions can be all-inclusive. If situations occur that are not covered by this manual, the operator must
apply common sense and operate this DR SELF-FEEDING WOOD CHIPPER in a safe manner. Contact us at www.DRpower.com
or call 1-800-DR-OWNER (376-9637) for assistance.
Operating this chipper safely is necessary to prevent or minimize the risk of death or serious injury. Unsafe operation can create a
number of hazards for you. Always take the following precautions when operating this chipper:
•Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and
themselves.
•Your DR SELF-FEEDING WOOD CHIPPER is a powerful tool, not a plaything. Exercise extreme caution at all times. The
design of this machine is to chip wood. Do not use it for any other purpose.
•Ensure you know the steps on how to stop the chipper properly (see chapter 3).
•Operate this machine on a level surface only. Never operate your unit on a slippery, wet, muddy, or icy surface. Exercise
caution to avoid slipping or falling.
•Keep your face and body back from the chipper hopper to avoid accidental bounce back of any material.
•When feeding material into the chipper hopper, be extremely careful that pieces of metal, rocks, or other foreign objects are
not included. Personal injury or damage to the machine could result.
•Never allow an accumulation of processed material to build up in the discharge area as this will prevent proper discharge and
can result in kickback from the chipper hopper.
•Always stop the engine when moving the DR SELF-FEEDING WOOD CHIPPER.
•See manufacturer’s instructions for proper operation and installation of accessories. Only use accessories approved by DR
Power Equipment.
•If the cutting mechanism strikes a foreign object or if your machine should start making an unusual noise or vibration, shut
down the engine, wait for all moving parts to come to a complete stop (the flywheel will continue rotating for a while after the
engine is shut down), disconnect spark plug wire, keeping it away from the spark plug to prevent accidental starting, then wait
5 minutes before inspecting for clogging or damage. Vibration is generally a warning of trouble. Clean and repair and/or
replace damaged parts.
•Never tamper with safety devices. Check their proper operation regularly.
•Stay alert for hidden hazards or traffic. Never carry passengers on your machine.
•Never overload or attempt to chip material beyond the manufacturer’s recommendation; see chapter 3. PERSONAL INJURY
or damage to the machine could result.
•While using the DR SELF-FEEDING WOOD CHIPPER, don't hurry or take things for granted. When in doubt about the
equipment or your surroundings, stop the machine and take the time to look things over.
•Never operate the machine when under the influence of alcohol, drugs, or medication.
•Use the machine only in daylight.
•Keep all nuts and bolts tight and keep the equipment in good operating condition.

CONTACT US AT www.DRpower.com 9
Chapter 2: Setting Up the DR SELF-FEEDING WOOD CHIPPER
This chapter outlines assembly and a few simple steps you will need to follow to set up your new machine before you use it. It may
be helpful to familiarize yourself with the controls and features of your DR SELF-FEEDING WOOD CHIPPER as shown in Figure 1
before beginning these procedures. If you have any questions at all, please feel free to contact us at www.DRpower.com or call our
Customer Service Representatives at our toll free number: 1-800-DR-OWNER (376-9637).
DR SELF-FEEDING WOOD CHIPPER Controls and Features
Key
Switch
Oil Drain
Discharge
Chute
Figure 1
Blow Back
Shield
Access Cover
for Chipper
Knife Check
Belt Guard
Choke Lever
Fuel Fill
Cap
Belt
Tensioner
Tongue
Assembly
Wheel
Assembly
Fuel
Shut-off
Throttle
Lever
On/Off Key
Switch
Starter
Cord
Hopper
Assembly
Battery
Chipper Knife
Wear Plate
Oil Fill/Dipstick
Fuel Fill Cap
Pro 475 Engine
Oil Drain
Plug
Hopper Removed
Pro XL-575 Yard-
Tow Model Shown

10 DR® SELF-FEEDING WOOD CHIPPER
Specifications
Models
PRO-475 - Manual and Electric Start Models
PRO XL-575
Engine
Briggs & Stratton (See Engine Manual for Engine
Specifications)
Briggs & Stratton Electric Start (See Engine Manual
for Engine Specifications)
Series
1650
2100
HP(Torque)
11.5 (16.5 Ft-lbs)
13.5 (21 Ft-lbs)
Chipping Capacity
4-3/4" Diameter
5-3/4" Diameter
Number of
Chipper Knives
1
1
Chipper Knife Size
6-1/4" x 1-1/4" x 9/32"
7-1/4" x 1-1/4" x 9/32"
Chipper Knife
Material
Heat Treated Tool Steel
Heat Treated Tool Steel
Wear Plate
Adjustable
Adjustable
Chipper Flywheel
17-3/4" Diameter x 5/8" Thick
20" Diameter x 5/8" Thick
Flywheel Weight
50 Lbs
62.5 Lbs
Chipper Knife Tip
Speed
128 mph
144 mph
Wheel Size
4.10/3.50-6 Pneu. (Yard-Tow Models)
4.80/4.00-8 Pneu. (Road-Tow Models)
4.10/3.50-6 Pneu. (Yard-Tow Models)
4.80/4.00-8 Pneu. (Road-Tow Models)
Axle
3/4" Diameter (Yard-Tow Models)
1" Diameter w/Welded Angle (Road-Tow Models)
3/4" Diameter (Yard-Tow Models)
1" Diameter w/Welded Angle (Road-Tow Models)
Hopper Opening
at Top
17" x 27"
19" x 30-1/2"
Assembly Parts Identification
Parts supplied in Shipping Crate:
•DR SELF-FEEDING WOOD CHIPPER
•Hopper Assembly
•Parts Box containing (Figure 2):
−Discharge Chute
−Safety &Operating Instructions Manual
−Engine Owner’s Manual
−Road-tow Wire Harness
−Hardware Package (see Figure 3 and Table below)
Hardware Package (Figure 3):
Item # Part # Description Qty
1 ........... 112411..... Flat Washer, 5/16" ......................................4
2 ........... 110761..... Nut, Nylon Lock, 5/16-18 ...........................6
3 ........... 189801..... Bolt, 5/16-18 x 4-1/2", GR5.........................2
4 ........... 112141..... Cable Tie......................................................12
Compare the contents of the Shipping Crate and Hardware Package with the
“Parts Supplied” list above. If you have any questions, please contact us at
www.DRpower.com or call 1-800-DR-OWNER (376-9637) for assistance.
1
Figure 3
3
4
2
Discharge
Chute
Road-tow
Wire Harness
Safety &
Operating
Instructions
Manual
Hardware
Package
Engine
Owners
Manual
Figure 2

CONTACT US AT www.DRpower.com 11
- IMPORTANT FIRST STEP ! -
Setting the Gap between Knife and Wear Plate
BEFORE you begin assembling the Chipper, you must set the clearance between
the Knife and Wear Plate to 1/16" (Figure 4) by using the Knife Gap Gauge.
First remove the Knife Gap Gauge that has been installed temporarily under the
Wear Plate as described below.
Tools Needed:
•Gap Gauge (provided with Chipper)
•7/16” Wrench
1. Loosen the three Locknuts on the Carriage Bolts enough to remove the
Knife Gap Gauge (Figure 5).
2. Use a stick to rotate the Flywheel so the Knife is positioned next to the Wear
Plate (Figure 6).
3. Position the Knife Gap Gauge as shown and push the Wear Plate against it
so the Gauge is touching both the Knife and Wear Plate. Tighten the
outside Locknut, check the gap, tighten the inside Locknut and then the
center Locknut.
4. Slide the Knife Gap Gauge in between the Knife and Wear Plate as shown to
check the gap at the entire length of the Wear Plate.
•If the Knife Gap Gauge slides freely with no resistance and a lot of
extra space, readjust the Wear Plate as described in the previous
steps.
•If the Knife Gap Gauge will not slide down between the Knife and
Wear Plate, readjust the Wear Plate as described in the previous
steps.
•If the Knife Gauge slides in between the Knife and Wear Plate with
some resistance felt against them both or slides in between with
no noticeable space, then the Wear plate is properly adjusted.
Ensure the Locknuts are tight and continue to the next step.
5. When adjustment is finished, rotate the Flywheel with a long stick to ensure
that it is rotating freely.
6. Continue to page 12 for instructions on assembling the Chipper.
Knife Gap
Gauge
Figure 5
Locknuts
and
Carriage
Bolts
Wear Plate
Knife Gap
Gauge
Figure 6
Knife
Wear
Plate
Flywheel
Locknuts and
Carriage Bolts
1/16" Gap
(thickness of
Gap Gauge)
Figure 4
Chipper
Knife
Wear
Plate
Flywheel

12 DR® SELF-FEEDING WOOD CHIPPER
Attaching the Hopper Assembly
Note: We recommend that you have someone help you lift the Hopper in place and
support it until it is secured to the Chipper.
Tools Needed:
•Two 1/2" Wrenches
For Pro-475 Models:
1. Remove and discard the three Shipping Nuts from the Housing Bolts, but
leave the Housing Bolts in place (Figure 7a).
2. Position the Hopper Assembly onto the Housing Support and Stud (Figure
8a) and secure the upper Bolts to the Hopper Assembly with two 5/16-18
Locknuts and Washers.
3. Secure the lower right Bolt to the Hopper Assembly with a 5/16-18 Locknut
(no Washer).
4. Install a 5/16-18 Locknut and Flat Washer to the lower Housing Stud.
For Pro XL-575 Models:
1. Remove and discard the Shipping Nut from the Housing Bolt, but leave the
Housing Bolt in place (Figure 7b.)
2. Position the Hopper Assembly onto the Housing Support and the three
Housing Studs (Figure 8b) and secure the Bolt to the Hopper Assembly
with a 5/16-18 Locknut and Washer.
3. Install three 5/16-18 Locknuts and Flat Washers to the three Studs.
Bolts and
Locknuts
Figure 7a: Pro-475
Housing
Stud
Housing
Support
Bolt and
Locknut
Figure 7b: Pro XL-575
Housing
Studs
Housing
Support
Figure 8a: Pro-475
Hopper
Chipper
Assembly
Bolt, Locknut and
Washer (Upper
Left and Right)
Spacer
Bolt and Locknut
(Lower Right)
Locknut
(Lower Left)
Figure 8b: Pro XL-575
Hopper
Chipper
Assembly
Locknut and Washer
(Two on other side of
Hopper Also)
Bolt, Locknut
and Washer

CONTACT US AT www.DRpower.com 13
Attaching the Discharge Chute
Tools Needed:
•Two 1/2" Wrenches
Note: You may need to loosen surrounding hardware near the Discharge Chute
mounting holes to make it easier to insert the Discharge Chute between the
Housing Plates (Figure 9). Tighten all hardware when finished.
1. Position the Discharge Chute facing away from the Hopper as shown and
secure with two 4-1/2" long 5/16-18 Bolts and Locknuts.
Installing the Wiring for the Road Tow Model
Tools and Supplies Needed:
•Two 3/4" Wrenches
•Wire strippers/Cutters
•Electrical Tape (or equivalent)
•Cable Ties (Supplied with machine)
1. Remove the Tow Hitch Bolts and Locknuts (Figure 10). Remove the Tow
Hitch.
2. Unwrap the Wiring Harness and locate the two colored wire ends that do
not have connectors on them (Figure 11).Note: The white wire will not be
used in this step.
3. Tape the ends of the wires together and also tape them together
approximately 6" from the end.
4. Insert the taped end of the wires into the Tow Bar and push the wires over
the Chain Bolt (Figure 12). Continue pushing the wires until they reach the
large hole at the center of the Tow Bar (Figure 13).
5. Pull the ends of the wires through the large Hole using a stiff wire with a
small hook formed at the end.
6. Continue pulling the Wires through leaving approximately three feet of the
Plug end extended beyond the front of the Tow Bar (Figure 12).Note: You
will want enough extra wire to plug into the tow vehicle and allow turning
without binding.
7. Position the Yellow/Brown Wires along the left side of the axle and up to
the light location over the Fender (Figure 14).
8. Position the Green/Brown Wire along the right side of the axle and up to
the Light location over the Fender.
9. Secure the Wires under the Frame with Cable Ties at the four places shown.
Discharge
Chute
Bolts and
Locknuts
Hopper
Figure 9
Chipper
Housing
Figure 14
Cable Ties
Yellow/
Brown
Wire
Wires
Bolts and
Locknuts
Figure 10
Tow Hitch
Wire Ends
Figure 11
Tape
Wires
Figure 12
Tow Bar
Chain Bolt
Wires
Figure 13
Tow Bar
Larger Hole

14 DR® SELF-FEEDING WOOD CHIPPER
10. There may be as much as 16 feet of extra wire at each Tail Light location
(Figure 15). Cut the excess Wire, leaving enough to insert into the back of
each Light after Wires are stripped in the next step.
11. Strip (remove) 1/2" of insulation from the ends of the Yellow/Brown wires
and Green/Brown wires with Wire Strippers and twist the individual wire
ends to aid in installation.
12. At the left side of the Chipper, insert the Yellow Wire into the top left hole in
the back of the light socket. Insert the Brown Wire into the top right hole.
Note: The wires are retained in the light socket holes by spring-loaded connectors.
13. At the right side of the Chipper, insert the Green Wire into the top left hole
in the back of the light socket. Insert the Brown Wire into the top right
hole.
14. Secure the Wires to the Light Brackets with Cable Ties.
15. Reinstall the Tow Hitch and secure with the Bolts and Locknuts, but leave
the front bolt loose for the following steps (Figure 10).
16. Remove the Ring Terminal from the end of the White Ground Wire with
Wire Cutters (Figure 16).
17. Remove 1" of insulation from the end of the Ground Wire with the Wire
Strippers.
18. Wrap the White (Ground) Wire around the front Tow Hitch Bolt and tighten
the Bolt.
19. Secure the Wires to the Tongue Assembly between the two large Bolts to
ensure they will not get caught between the Tongue and Ball of the Tow
vehicle (Figure 17).
20. Secure the colored and white wires together with some Cable Ties.
Figure 17
Cable Tie
Tongue
Assembly
Light Plug
Cable Ties
Figure 15
Tail Light
Yellow/Brown
Wires
Cable Tie
Figure 16
Ground Wire
Hitch Bolt

CONTACT US AT www.DRpower.com 15
Figure 20
Negative
Battery
Cable
Battery
•You must add oil before starting the engine. This machine is shipped without oil. Traces of oil may be in the reservoir from
factory testing, but you must add oil before starting the engine. Fill the reservoir slowly checking the dipstick frequently to
avoid overfilling.
•To get an accurate reading when checking the oil level:
- The machine should be on a level surface.
- The dipstick should be pushed all the way down and turned a quarter turn clockwise for the 16.5 Model (long Dipstick) to
ensure an accurate oil level reading.
- The dipstick should not be screwed in for the 21.0 Model (short Dipstick) to ensure an accurate oil level reading.
Positioning the Support Leg from Towing to Operating Position
1. Pull the Hitch Clip from the Pin and pull the Pin from the Support Leg and
Tow Bar (Figure 18).
2. Rotate the Support Leg to the down (operating) position, align the holes in
the Tow Bar and Leg, reinstall the Pin and secure with the Hitch Clip
(Figure 19).
Connecting the Battery Cable (Electric Start)
We ship the electric-start DR SELF-FEEDING WOOD CHIPPER with the
negative terminal battery cable disconnected. This prevents the battery from
discharging during shipment. Before using your electric start DR SELF-
FEEDING WOOD CHIPPER, you must connect the battery cable.
Tools Needed:
•5/16" Wrench
•Phillips Head Screwdriver
1. Connect the Negative Battery Cable onto the Negative Terminal Lug of the
Battery with the existing Bolt, Washer and Nut using a 5/16" Wrench and a
Phillips Head Screwdriver (Figure 20).
Adding Engine Oil and Gasoline
Capacities
Engine
See engine Owners Manual
Fuel Tank
Unleaded gasoline, 4 US quarts (3.79 L)
Tip: To avoid confusion, we recommend leaving the caps on the gas and oil fills until you are ready to pour either gasoline or oil
into the correct fill.
Note: Use SAE 30 high detergent oil classified “For Service SF, SG, SH, SJ” or higher. Do not use special additives. Other types of oil
could cause problems operating your machine. Please refer to your Engine Owner’s Manual for detailed oil information.
Tow Bar
Figure 19
Support Leg
Pin w/Hitch
Clip
Figure 18
Support Leg
Pin w/Hitch
Clip
Tow Bar

16 DR® SELF-FEEDING WOOD CHIPPER
Adding Oil
1. Place the machine on a level surface and remove the Dipstick (clean the
end of the Dipstick with a rag) (Figure 21a and 21b).
2. Machines are shipped with no oil. Add 1/2 of the SAE 30 high detergent oil
recommended by the engine manufacturer and wait one minute for the oil
to settle.
3.
Pro-475: Install the Dipstick fully and turn a quarter turn clockwise to ensure an
accurate reading and then remove it to check the oil level.
Pro XL-575:Insert the Dipstick, but do not screw in, to ensure an accurate
reading and then remove it to check the oil level.
4. If the oil level is low, continue adding a few ounces of oil at a time,
rechecking the Dipstick until the oil reaches the fill mark (Figure 22a and
22b). Be careful not to overfill.
5. Install the Dipstick completely when finished.
Adding Gas
1. Remove the Gas Fill Cap and fill the Gas Tank with fresh, unleaded gas
(with a minimum of 85 Octane) to approximately 1" to 1-1/2" below the top
of the fill neck to allow for fuel expansion (Figure 21a and 21b). Be careful
not to overfill and reinstall the Gas Fill Cap before starting the engine. See
your Engine Owner’s Manual for more detailed information.
Note: To refill the gas tank, turn the engine OFF and let the engine cool at least five
minutes before removing the gas fill cap.
Check the Tire Pressure
Tools Needed:
•Tire Pressure Gauge
•Air Compressor
1. Remove the Valve Stem Protective Cap and check the tire pressure with a
Tire Pressure Gauge (Figure 23).
2. If the pressure is too low, add air through the Valve Stem with an air hose.
3. Replace the Valve Stem Protective Cap when finished.
Figure 23: Yard-Tow Model Shown
Valve Stem
Protective Cap
Operating
Range
Too Low
(add oil)
Too Full
(drain oil)
Figure 22a: Pro-475
Operating
Range
Too Low
(add oil)
Too Full
(drain oil)
Figure 22b: Pro XL-575
Figure 21a: Pro-475
Oil Check/Fill
Gas Fill Cap
Figure 21b: Pro-XL 575
Gas Fill Cap
Oil Check/ Fill
Do not over inflate the tires. Inflate to the manufacturers recommended
pressure found on the tires.

CONTACT US AT www.DRpower.com 17
Chapter 3: Operating Your DR SELF-FEEDING WOOD CHIPPER
Before Starting the Engine
1. Check the oil level every time you use the DR SELF-FEEDING WOOD
CHIPPER. Add oil if needed (see Chapter 2 section “Adding Engine Oil and
Gasoline”.
2. Check the fuel level. Add fuel as needed (see Chapter 2 section “Adding
Engine Oil and Gasoline”.
3. Ensure that the Fuel Shut-Off Valve is in the “ON” position (Figure 24).
4. Remove any debris buildup from the machine before every use of the
Chipper.
Note: Check and re-tighten the Drive Belt, if necessary, after an initial break-in
period of one (1) hour (see Chapter 4 “Maintaining the DR SELF-FEEDING
WOOD CHIPPER”).
Operation Notes
•Visually check the Chipper Knife for damage before each use of the
machine. See “VISUAL inspection of the Chipper Knife (before each use)”
in Chapter 4 for info on accessing the Chipper Knife.
•At engine start-up, the engine of your DR SELF-FEEDING WOOD
CHIPPER operates under no load until approximately 1000 RPM, at which
speed the Centrifugal Clutch engages and begins driving the Rotor
Assembly. Always operate the Engine at full speed when chipping.
•Only operate the DR SELF-FEEDING WOOD CHIPPER from the Operator
Zones shown (Figure 25).
•Keep proper balance and footing while operating the DR SELF-FEEDING
WOOD CHIPPER.
•ALWAYS stop the engine when leaving the Operating Zones or when
moving the machine.
•Never move the Chipper while the engine is running or the Flywheel is
turning.
Figure 25
Operator
Zone
Operator
Zone
Discharge
Area
Top View
Hopper
Fuel Shut-Off
Valve
Figure 24
•The design of this machine is for chipping wood. Never use this machine for any other purpose as it could cause serious
injury.
•Contact with internal rotating parts will cause serious personal injury. Never put hands, face, feet, or clothing into chipper
hopper or discharge opening or near the discharge area at any time.
•Before performing any maintenance procedure or inspection, shut down the engine, wait for all moving parts to come to a
complete stop (The flywheel will continue rotating for a while after the engine is shut down), disconnect spark plug wire,
keeping it away from the spark plug to prevent accidental starting, disconnect the negative battery cable, then wait 5 minutes
before proceeding.
•Use only a wooden stick to clear jammed material.

18 DR® SELF-FEEDING WOOD CHIPPER
Use common sense when using the Machine. Learn to recognize the change in sounds when overloaded. Turn Off the Engine
immediately if the machine becomes jammed to prevent damage to the Drive System
Never throw remaining Stubs or Knots into the Chipper Hopper; Damage will Result.
Processing Material
The Chipper is designed to accept wood only. The Chipper Knife mounted on a revolving flywheel turns branches fed into the
Chipper Hopper into “chips”. Cut your materials into manageable lengths before feeding them into the Chipper Hopper.
•Your DR SELF-FEEDING WOOD CHIPPER can process dry or green wood up to 4-3/4" (16.5) or 5-3/4" (21.0) in diameter.
•The Chipper will self-feed the wood once it contacts the knife edge so forcing the branches into the Hopper is not necessary if
the knife is sharp.
•Green wood will process quicker and easier than dry wood.
•Softwood processes easier than hardwood.
•Your operator experience will teach you how different types of wood will chip and how fast you can process them.
•When chipping branches, sometimes a tail will develop at the end of a branch. To avoid this, rotate the branch while feeding
it into the Chipper Hopper.
•Rotating the branch as you feed it into the machine will improve chipping performance.
•Use caution with small diameter green saplings and branches less than 2" in diameter. Chip these grouped or bundled
together to provide support for each other. If the material is 2" or larger, feed only one at a time into the Chipper Hopper.
•Make sure the DR SELF-FEEDING WOOD CHIPPER finishes processing material in the Hopper before shutting the engine
off.
•Do not force material into the Chipper. If the machine does not chip well, the Chipper Knife may need sharpening or
replacement, or the gap between the Knife and the Wear Plate needs adjusting. See “Removing, Replacing and Adjusting the
Chipper Knife and Wear Plate” in Chapter 5.
•Extremely hard knots will not process very well. Push any short stubs that have not self-fed through the Chipper, with the next
branch to be chipped.
•Cut the material to be chipped into manageable lengths of no more than five or six feet long before chipping them.
•Overloading the Chipper Hopper will cause the rotor speed to decrease. If you hear the engine RPM decreasing, stop feeding
material into the Chipper Hopper until the engine has returned to full speed.
•Always wear protective goggles or safety glasses with side shields while chipping to protect your eyes from possible thrown
debris.
•Avoid wearing loose clothing or jewelry, which might catch on moving parts or the material fed into the chipper hopper.
•We recommend wearing gloves while chipping. Be sure your gloves fit properly and do not have loose cuffs or drawstrings.
•Wear shoes with non-slip treads when using your chipper. If you have safety shoes, we recommend wearing them. Do not
use the machine while barefoot or wearing open sandals.
•Wear long pants while operating the DR SELF-FEEDING WOOD CHIPPER.
•Use ear protectors or ear plugs rated for at least 20 dba to protect your hearing.
The chipper hopper must be securely bolted to your DR SELF-FEEDING WOOD CHIPPER and the blowback shield in place before
using the machine!

CONTACT US AT www.DRpower.com 19
Starting the Engine (Manual Start Model)
1. Ensure that the Fuel Shut-Off is in the “ON” position to the right (Figure
26).
2. Move the Choke Control Lever to the “CHOKE” position to the left (leave in
the RUN position to the right if the engine is already warm).
3. Move the Throttle Control Lever to about half way between Slow (turtle)
and Fast (rabbit) position.
4. Slowly pull the Starter Cord until you feel resistance, then pull quickly. The
Cord will recoil back into position.
5. When the Choke is on, the Engine will soon begin to run rough. Adjust the
Choke to the right until the engine runs smoother. Continue this process
until the engine runs well with the Choke Lever fully in the run position.
Note: Ensure that the Choke Lever is always in the right “Run” position before
operating the machine.
6. When the Engine is warmed up and running smoothly with the Choke in
the “RUN” position, move the Throttle Control Lever to the fast (rabbit)
position for chipping.
Starting the Engine (Electric Start Model)
1. Ensure that the Fuel Shut-Off is in the “ON” position (Figure 26).
2. Move the Choke Control Lever to the “CHOKE” position to the left (leave in
the RUN position to the right if the engine is already warm).
3. Move the Throttle Control Lever to about half way between Slow (turtle)
and Fast (rabbit) position.
4. Turn the Key to the “START” position until the engine starts and then
release it (Figure 27). The Key Switch will snap back to the “RUN” position
5. When the Choke is on, the Engine will soon begin to run rough. Adjust the
Choke to the right until the engine runs smoother. Continue this process
until the engine runs well with the Choke Lever fully in the run position.
Note: Ensure that the Choke Lever is always in the right “Run” position before
operating the machine.
6. When the Engine is warmed up and running smoothly with the Choke in the “RUN” position, move the Throttle Control Lever
to the fast (rabbit) position for chipping.
Stopping the Engine
1. Slowly move the Throttle Control Lever all the way to the slow position (turtle icon).
2. For electric start models, turn the Key to the off position to stop the engine. Remove the Key for safety.
Note: Close the Fuel Shut-Off when transporting or storing the DR SELF-FEEDING WOOD CHIPPER.
Starter Cord
Figure 26
Choke Lever
Throttle
Control
Lever
Fuel Shutoff
Figure 27
Start
Run
Stop
Shut down the Engine (The flywheel will continue to rotate for a while after the engine is shut off), Wait 5 minutes for the engine
to cool and all moving parts to come to a complete stop, remove spark plug wire and disconnect the negative battery cable before
moving or working on the chipper.

20 DR® SELF-FEEDING WOOD CHIPPER
Figure 28
Tow Hitch
Assembly
Clevis Pin
Hitch Clip
Connecting the DR SELF-FEEDING WOOD CHIPPER to your
Tractor –Yard-Tow Models
1. Lift the Chipper Tow Bar onto the Tractor Hitch and install the Hitch Pin
and Hitch Clip to secure it (Figure 28).
2. Pull the Hitch Clip from the Pin and pull the Pin from the Support Leg and
Tow Bar (Figure 29).
3. Rotate the Support Leg to the up (transport) position, align the holes in the
Tow Bar and Leg, reinstall the Pin and secure with the Hitch Clip (Figure
30).
Connecting the DR SELF-FEEDING WOOD CHIPPER to your
Vehicle –Road-Tow Models
1. Pull the latch assembly on the Tow Hitch Assembly up and into the open
position. Position the hitch coupler of the Chipper over and onto the tow
vehicle’s tow ball (must be a 2" tow ball) (Figure 31).
2. Pull the Hitch Clip from the Pin and pull the Pin from the Support Leg and
Tow Bar (Figure 29).
3. Rotate the Support Leg to the up (transport) position, align the holes in the
Tow Bar and Leg, reinstall the Pin and secure with the Hitch Clip (Figure
30).
4. Close the Latch Assembly on the Tow Hitch Assembly to lock it onto the
Tow Ball (Figure 32). Attach the towing Safety Chains to the tow vehicle
ensuring there is enough slack for turning.
5. Insert the Locking Pin into the hole in the Latch Assembly.
Figure 32
Tow
Hitch
Assembly
Latch
Assembly
Safety
Chains
Figure 30
Support Leg
Pin w/Hitch
Clip
Tow Bar
Tow Bar
Figure 29
Support Leg
Pin w/Hitch
Clip
Figure 31
Tow
Hitch
Assembly
2" Tow Ball
Latch
Assembly
Avoid death or serious injury. Do not exceed 10 mph when towing the Yard-
Tow model. Never tow the Yard-Tow model over roads.
Always secure the Support Leg in the up (transport) position before towing to
prevent damage to the machine.
Always secure the Support Leg in the up (transport) position before towing to
prevent damage to the machine.