Dragon Wholesaling 6015 HO GSR2 User manual

6015 HO GSR2
Fireplace (Aust)
• Direct Vent Fireplace
• Natural Gas or Propane
• Vent Horizontally or Vertically
• Standard Residential
• Mobile Home Approved
Listed by
AS/NZS 5263.1.3 GMK 10166
IAPMO-R&T OCEANA
WARNING: If the information in these instructions is not followed exactly, a fire or explosion may result
causing property damage, personal injury or loss of life.

DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.

DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.

DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN OPERATION.

DO NOT MODIFY THIS APPLIANCE.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any phone in your building.
• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
This appliance may be installed in
an aftermarket permanently
located, manufactured home (USA
only) or mobile home, where not
prohibited by local codes.
This appliance is only for use
with the type(s) of gas indicated
on the rating plate. A conversion
kit is supplied with the appliance.
Installation Manual
Installer: After installation give this manual to the home-
owner and explain operation of this heater.
 Copyright 2018, T.I. $10.00 100-01370 5/3/2021
Dragon Wholesaling Pty. Ltd.
Unit 4, 16 Lexington Drive
Bella Vista NSW
Australia 2153
www.travisproducts.com
12521

2 Introduction
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Overview
This manual details the installation
requirements for the 6015 HO GSR2 fireplace.
For operating and maintenance instructions,
refer to the 6015 HO GSR2 Owner's Manual.

Table of Contents 3
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Overview ................................................................... 2
Installation Options .................................................. 6
Heating Specifications ............................................. 6
Dimensions ............................................................... 6
Packing List .............................................................. 7
Additional Items Required ....................................... 7
Recommended Installation Procedure ................... 7
Fireplace Placement Requirements ....................... 8
Clearances ......................................................................8
Raised Fireplaces ............................................................8
Televisions Placed Above the Fireplace ................ 9
Using a Mantel Between the Fireplace and Television ....9
Using a Recessed Fireplace Below a Television .............10
Using a Recessed Fireplace with a Recessed
Television ........................................................................11
Minimum Framing Dimensions – NG (all
configurations) or LP with 36” Rise (or greater) ... 12
Preparing the Vertical Supports for 66” Tall
Framing ..................................................................... 13
Minimum Framing Dimensions – LP with
Minimum Vent (24” Rise) ......................................... 14
Nailing Brackets – Standard Install ........................ 15
Standard vs. Extended Position ............................. 16
Corner Installations .................................................. 17
Removing the Front Panel ....................................... 18
Gas Line Requirements ........................................... 19
Fuel .................................................................................19
Gas Line Connection .......................................................19
Gas Inlet Pressure ...........................................................19
Directions for Connecting a Gas Pressure Test Gauge ...19
Gas Line Location ............................................................20
Relocating the Gas Line to the Baseplate ...................... 20
Electrical Connection ............................................... 21
Relocating the Electrical Line to the Baseplate .............. 21
Vent Requirements ................................................... 22
Vent Clearances ..............................................................22
Vent Firestop ...................................................................22
Altitude Considerations ....................................................22
Approved Vent .................................................................22
Vent Installation ...............................................................22
Vertical Pipe Shield .........................................................23
Minimum Vent Pipe Shield – Used for Minimum Vent
Applications Only .............................................................24
Horizontal Termination Exhaust Shield ............................25
Approved Vent Configurations ............................... 26
Restrictor Position ...........................................................26
Exhaust Restrictor ...........................................................26
Intake Restrictor ..............................................................27
Diffuser ............................................................................28
Minimum Vent Configuration .................................. 29
NG Vent Configurations – Vertical Termination .... 30
NG Vent Configurations – Horizontal
Termination (Min. 30” Rise) ..................................... 31
LP Vent Configurations – Vertical Termination ..... 32
LP Vent Configurations – Horizontal
Termination (Min. 36” Rise) ..................................... 33
Termination Requirements ...................................... 34
Hearth Requirements ............................................... 35
Non-Combustible Framing (included) .................... 36
Facing Requirements ............................................... 37
Standard vs. Extended Position ...................................... 38
Facing Example – Standard Position – Flush Install ....... 39
Facing Example – Standard Position - Tile-Over Install .. 40
Do Not Drill or Screw Zone .............................................. 41
Mantel Requirements ............................................... 42
Mantel Column Clearances ........................................... 43
Use of a Non-Combustible Mantel Below Listed
Mantel Clearances .................................................... 44
Steps for Finalizing the Installation ........................ 45
Air Shutter Adjustment..................................................... 46
Glass Frame Removal and Installation .................. 47
Fireback Installation ................................................. 49
Crushed Glass Installation ...................................... 51
LP Conversion Instructions .................................... 52
Wiring Diagram ......................................................... 56
Power Heat Duct Installation ................................... 57
6015 CoolSmart TV (Optional) ................................. 58
Installation Overview ....................................................... 58
CoolSmart TV - Installation Requirements ............ 59
Combustible “Over-Facing” (Optional) .................. 60
CoolSmart TV - Flush Facing Header
Configuration and Facing ........................................ 60
CoolSmart TV - Framing the Chase ........................ 62
CoolSmart TV - Fireplace Preparation .................... 63
Knockout Removal .......................................................... 64
CoolSmart TV – Mantel Clearances ........................ 66

4 Safety Precautions
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Safety Warnings
 Failure to follow all of the requirements may result in property damage, bodily injury, or even death.
 This unit must be installed by a qualified installer to prevent the possibility of an explosion.
 This appliance must be installed in accordance with all local codes, if any; if not, in U.S.A. follow ANSI
Z223.1 and NFPA 54(88), in Canada follow CSA B149.1. In Australia follow AS/NZS 5601.1.
 A manufactured home (USA only) or mobile home OEM installation must conform with the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, or, when such a
standard is not applicable, the Standard for Manufactured Home Installations, ANSI/NCSBCS
A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing, CSA Z240.4. This
appliance may be installed in Manufactured Housing only after the home is site located.
 All exhaust gases must be vented outside the structure of the living-area. Combustion air is drawn
from outside the living-area structure. The venting must not be connected to a chimney flue serving a
separate solid-fuel burning appliance.
 Notify your insurance company before hooking up this fireplace.
 The room heater should be inspected before use and at least annually by a qualified service person.
More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc.
 The instructions in this manual must be strictly adhered to. Do not use makeshift methods or
compromise in the installation. Improper installation will void the warranty and safety listing.
 This heater is approved for use with natural gas (NG) or propane (LP). Burning the incorrect fuel will
void the warranty and safety listing and may cause an extreme safety hazard. Direct questions about
the type of fuel used to your dealer.
 Contact your local building officials to obtain a permit and information on any installation restrictions
or inspection requirements in your area.
 If the flame becomes sooty, dark orange in color, or extremely tall, do not operate the heater. Call
your dealer and arrange for proper servicing.
 It is imperative that control compartments, screens, or circulating air passageways of the heater be
kept clean and free of obstructions. These areas provide the air necessary for safe operation.
 Do not operate the heater if it is not operating properly in any fashion or if you are uncertain. Call
your dealer for a full explanation of your heater and what to expect.
 Do not store or use gasoline or other flammable liquids in the vicinity of this heater.
 Do not operate if any portion of the heater was submerged in water or if any corrosion occurs.
Immediately call a qualified service technician to inspect the appliance and to replace any part of the
control system and any gas control which has been under water.
 Do not place clothing or other flammable items on or near the heater. Because this heater can be
controlled by a thermostat there is a possibility of the heater turning on and igniting any items placed
on or near it.
 Light the heater using the built-in igniter. Do not use matches or any other external device to light
your heater.
 Never remove, replace, modify or substitute any part of the heater unless instructions are given in this
manual. All other work must be done by a trained technician. Don't modify or replace orifices.
 The viewing glass should be opened only for conducting service.
 Any safety screen or guard removed for servicing must be replaced prior to operating the heater.

Safety Precautions 5
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Safety Warnings (continued)
 Allow the heater to cool before carrying out any maintenance or cleaning.
 Operate the heater according to the instructions included in this manual.
 If the main burners do not start correctly turn the gas off and call your dealer for service.
 This unit is not for use with solid fuel.
 Do not place anything inside the firebox (except approved Travis Industries components).
 Warning: Do not operate appliance with the glass front removed, cracked or broken. Replacement
of the glass should be done by a licensed or qualified service person.
 Do not throw this manual away. This manual has important operating and maintenance instructions
that you will need at a later time. Always follow the instructions in this manual.
 Young children should be carefully supervised when they are in the same room as the appliance.
Toddlers, young children and others may be susceptible to accidental contact burns. A physical
barrier is recommended if there are at risk individuals in the house. To restrict access to a fireplace
or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals
out of the room and away from hot surfaces.
 Children and adults should be alerted to the hazards of high surface temperature and should stay
away to avoid burns or clothing ignition. Do not touch the hot surfaces of the heater. Educate all
children of the danger of a high-temperature heater.
 Due to the high temperature, the heater should be located out of traffic and away from furniture and
draperies.
 Instruct everyone in the house how to shut gas off to the appliance and at the gas main shutoff valve.
The gas main shutoff valve is usually next to the gas meter or propane tank and requires a wrench to
shut off.
 Travis Industries, Inc. grants no warranty, implied or stated, for the installation or
maintenance of your heater, and assumes no responsibility of any consequential damage(s).
SAFETY WARNINGS:
 DO NOT PLACE ARTICLES ON OR AGAINST THIS APPLIANCE.
 DO NOT USE OR STORE FLAMMABLE MATERIALS NEAR THIS APPLIANCE.
 DO NOT SPRAY AEROSOLS IN THE VICINITY OF THIS APPLIANCE WHILE IT IS IN
OPERATION.
 DO NOT MODIFY THIS APPLIANCE.
 THIS INSTALLATION MUST CONFORM WITH THE FOLLOWING:
 Manufacturer’s Installation instructions
 Local Gas Fitting Regulations
 Municipal Building Codes,
 Refer to AS/NZS 5601.1 for Gas Installations.
 S.A.A. Wiring Code
 Local Electrical Regulations
 Any other statutory regulations
 NOT SUITABLE FOR MARINE USE.
 NOT INTENDED FOR FIREPLACE INSERT.
 APPLIANCES INCORPORATING A LIVE FUEL EFFECT, AND DESIGNED TO
OPERATE WITH LUMINOUS FLAMES, MAY EXHIBIT SLIGHT CARBON
DEPOSITION.

6 Features and Specifications
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Installation Options
 Residential or Mobile Home
 Straight or Corner Placement
 Raised or Floor Placement
 Internal or External Chase
 Bedroom Approved
Heating Specifications
Natural Gas Propane
Approximate Heating Capacity (in square meters)* Up to 260 Up to 260
Maximum BTU Input Per Hour (MJ/H) 59.1 59.1
* Heating capacity will vary with floor plan, insulation, and outside temperature.
Dimensions

Installation (for qualified installers only) 7
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Packing List
 Propane Conversion Parts
 Remote Control
 4 AA Batteries, 3 AAA Batteries
 Glass Latch Tool
 (2) Firestops (8” Diameter)
 Non-Combustible Framing (3 pieces)
 Minimum Vent Pipe Shield
 Horizontal Termination Exhaust Shield
Additional Items Required
 If using LP (propane) a conversion kit is required (4-pack = 94400999, single = 250-01463).
 Gas Line Equipment (shutoff valve, pipe, etc.)
 Electrical Equipment (min. 14 gauge, grounded line)
 This Fireplace Requires Firebacks and 10 lbs. of 1/4” Crushed Glass
Firebacks 96100981 Stainless Steel
96100982 Black Enamel
96100983 Black Painted
96100984 Ledgestone
Crushed Glass 94500580 Platinum (10 lbs.)
94500581 Bronze (10 lbs.)
94500582 Cobalt (10 lbs.)
94500583 Black (10 lbs.)
Recommended Installation Procedure
 Frame the opening for the fireplace. Make sure to allow for vent installation.
 This fireplace is designed to accommodate 1/2" (13mm) drywall (see "Nailing Brackets" on page 13 for
details). Secure the fireplace to the framing.
 Install the vent, gas line and electrical hook-up.19
 Install the drywall.
 Install the hearth (if applicable).
 Install the facing (if applicable).
 Install the mantel (if applicable).
 Finalize the installation (see page 45).

8 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Fireplace Placement Requirements
 Fireplace must be installed on a level surface capable of supporting the fireplace and vent
 Fireplace must be placed directly on wood or non-combustible surface (not on linoleum or carpet)
 Fireplace should be located out of traffic and away from furniture and draperies.
 Fireplace must be placed so the gaps below and above the glass frame do not become blocked.
 Fireplace may be placed in a bedroom. Please be aware of the large amount of heat this appliance produces
when determining a location.
Clearances
(a) Clearance to Side of Fireplace 5/8” (16mm). Do not place insulation in this space.
NOTE: Drywall or other combustible may contact the side of the fireplace in front of the framing. The
material must not protrude in front of the fireplace and may be a maximum ½” (13mm) thick.
(b) Clearance to Back of Fireplace 1/8” (4mm). Do not place insulation in this space.
(c) When installed, walls in front of the fireplace must be a minimum 3” (77mm) to the side of the fireplace.
Raised Fireplaces
 The fireplace (and hearth, if desired) may be placed on a platform designed to support the fireplace and vent.
 The base of the fireplace must be a minimum 66” below the room ceiling.
The firebox opening is approximately 10.375” (264mm) above the base of the fireplace. For a
typical raised fireplace of 36” (915mm), place the fireplace on a platform 25.625” (651mm) tall.
LP MIN VENT APPLICATIONS: Framing opening for LP min vent applications is 72” (1829mm).
MAKE SURE TO ACCOMMODATE THE REQUIRED FRAMING OPENING.

Installation (for qualified installers only) 9
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Televisions Placed Above the Fireplace
The following section details three methods to allow for television installation above the fireplace.
Using a Mantel Between the Fireplace and Television
IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE
Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may
negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,
please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to
reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take
responsibility for any negative impact to televisions placed near this fireplace.
Minimum Dimensions:
(a) Mantel Height above Base of Fireplace
Mantel must fall within shaded portion of the chart above.
42” (1067mm) with 8” (203mm) mantel depth
See chart above if using a larger mantel.
(b) Mantel Depth* Minimum 8” (203mm)
* NOTE: The minimum mantel depth is 8”. This allows heat to travel forward and dissipate.
EXAMPLES: If you have a TV that is greater than 6” deep (including the 1” gap behind), you will need to alter the mantel
depth and height. If your TV is 9” deep (including the 1” gap behind), the mantel should be 11” (this provides the necessary 2”
recess for the TV). The 11” mantel would require a 43.5” (292mm) mantel height (see chart above).
WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to
protect from contact with hot surfaces.

10 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Using a Recessed Fireplace Below a Television
IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE
Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may
negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,
please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to
reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take
responsibility for any negative impact to televisions placed near this fireplace.
Minimum Dimensions:
(a) Fireplace Recess Height above Base of Fireplace
Recess must fall within shaded portion of the chart above.
42” (1067mm) with 8” (203mm) recess depth
See chart above if using a larger recess.
(b) Fireplace Recess Depth plus Mantel Depth* Minimum 8” (203mm)
(c) Fireplace Recess Width 69.5” (1766mm)
* NOTE: The minimum recess plus mantel depth is 8”. This allows heat to travel forward and dissipate.
EXAMPLES: If you have a TV that is 3” deep (including the 1” gap behind), you will need to put in a 5” mantel (the 2” is
measured from the front of the TV). The fireplace can then be recessed 3” into the wall to allow for the 8” of recess plus
mantel depth.
WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to
protect from contact with hot surfaces.

Installation (for qualified installers only) 11
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Using a Recessed Fireplace with a Recessed Television
IMPORTANT NOTE REGARDING TELEVISIONS AND THIS FIREPLACE
Most television manufacturers instruct the homeowner to not place the television above a heat source. Doing so may
negatively affect the longevity of the television and may negate the warranty. If you do place a television above the fireplace,
please be aware of the large amount of heat generated by the fireplace and consider placing the television above a mantel to
reduce the amount of heat that reaches the television. The homeowner must understand that Travis Industries does not take
responsibility for any negative impact to televisions placed near this fireplace.
Minimum Dimensions:
(a) Fireplace Recess Height above Base of Fireplace
Recess must fall within shaded portion of the chart above.
42” (1067mm) with 8” (203mm) recess depth
See chart above if using a larger recess.
(b) Fireplace/TV Recess Depth* Minimum 8” (203mm)
(c) Fireplace Recess Width 69.5” (1766mm)
* NOTE: The minimum recess depth is 8”. This allows heat to travel forward and dissipate.
EXAMPLES: If you have a TV that is greater than 6” deep (including the 1” gap behind), you will need to alter the fireplace
recess depth and height. If your TV is 9” deep (including the 1” gap behind), the recess should be 11” (this provides the
necessary 2” recess for the TV). The 11” recess would require a 43.5” (292mm) fireplace recess height (see chart above).
If you have a TV that is 3” deep (including the 1” gap behind), you will need to put in a 5” mantel (the 2” is measured from the
front of the TV). The fireplace can then be recessed 3” into the wall to allow for the 8” of recess plus mantel depth.
WIRING NOTE: If running wiring into the enclosure, use thermal insulating wrap around the wiring. Secure the wiring to
protect from contact with hot surfaces.

12 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Minimum Framing Dimensions – NG (all configurations) or LP with 36” Rise
(or greater)
The fireplace
enclosure must be a
minimum 66” tall (do
not build into the
fireplace enclosure)

Installation (for qualified installers only) 13
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Preparing the Vertical Supports for 66” Tall Framing

14 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Minimum Framing Dimensions – LP with Minimum Vent (24” Rise)
The fireplace enclosure must be a minimum 72” (1829mm) tall (do not build into the fireplace enclosure)

Installation (for qualified installers only) 15
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Nailing Brackets – Standard Install
The fireplace has nailing brackets on both sides. Secure the fireplace to the framing.
NOTE: Make sure the fireplace is square and plumb when placed in the framing. Measured corner-to-corner the
fireplace should be square. Use shims to insure the fireplace is square.
NOTE: The nailing brackets have two positions: standard and extended. See the section “Facing Requirements”
for details on which position is best for your installation.

16 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Standard vs. Extended Position
There are two positions that the standoff/heat shield assembly can be installed. The fireplace is shipped in the
standard (forward) position.
 If the unit is installed in the standard position no modification is needed.
 If the unit is being installed in the extended position, the drywall support/non-combustible framing must be
repositioned back ½” (see illustration below).
NOTE: see “Facing Requirements” for additional details about standard vs. extended installations.

Installation (for qualified installers only) 17
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Corner Installations
A typical 45° installation uses the framing dimensions shown in the illustration below (NOTE: all clearances still
apply).

18 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Removing the Front Panel
The front cover may be removed to access the components. This is required when relocating the electrical or gas
inlet location. To remove the front cover
(a) Remove the
center nut.
(b) Loosen the
two outer
nuts.
(c) Rotate the
front panel
down.
(d) Remove the
front cover.

Installation (for qualified installers only) 19
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Gas Line Requirements
MASSACHUSETTS INSTALLATIONS - WARNING:
THIS PRODUCT MUST BE INSTALLED BY A LICENSED PLUMBER OR GAS FITTER WHEN INSTALLED WITHIN THE
COMMONWEALTH OF MASSACHUSETTS.
OTHER MASSACHUSETTS CODE REQUIREMENTS:
 Flexible connector must not be longer than 36 inches.
 Shutoff valve must be a “T” handle gas cock.
 Only direct vent sealed combustion products are approved for bedrooms or bathrooms.
 Fireplace dampers must be removed or welded in the open position prior to the installation of a fireplace insert or gas log.
 A carbon monoxide (CO) detector is required in the same room as the appliance.
 The gas line must be installed in accordance with all local codes and the requirements listed below. In the
absence of local codes, follow ANSI 223.1 in US/Canada or AS/NZS 5601.1 in Australia.
 The fireplace and gas control valve must be disconnected from the gas supply piping during any pressure
testing of that system at test pressures in excess of 1/2 psig (3.5 kPA). For pressures under 1/2 psig (3.5
kPA), isolate the gas supply piping by closing the manual shutoff valve.
 Leak test all gas line joints and the gas control valve prior to and after starting the fireplace.
 This unit has been listed using the included internal gas shutoff valve.
Fuel
 This fireplace is designed either for natural gas or for propane (but not for both).
Gas Line Connection
 Installation must be performed by a qualified installer, service agency or the gas supplier (In Massachusetts a licensed
plumber/gasfitter).
Gas Inlet Pressure Standard Input Pressure
Natural Gas 1.74 kPa (Min. 1.13 kPa)
Propane 2.74 kPA
 If the pressure is not sufficient, make sure the piping used is large enough, the supply regulator is adequately adjusted,
and the total gas load for the residence does not exceed the amount supplied.
 The supply regulator (the regulator that attaches directly to the residence inlet or to the propane tank) should supply gas
at the input pressure listed above. Contact the local gas supplier if the regulator is at an improper pressure.
Directions for Connecting a Gas Pressure Test Gauge
The gas control valve (shown to the left) has two accessible ports for testing
line pressure and output pressure. Loosen the brass screw on either test port
and place a 5/16” i.d. rubber or plastic tubing over the tapered test port.
Connect the tubing to the test gauge.
WARNING: The brass screw must be tightened after testing to prevent gas
leakage.
Input pressure
Output pressure

20 Installation (for qualified installers only)
© Travis Industries 5/3/2021 - 1370 6015HO (AUST)
Gas Line Location
NOTE FOR RIGID PIPE: When using rigid pipe, you may wish to disconnect the shutoff valve from the fireplace
and route the pipe through the fireplace wall. First, disconnect the gas line from the shutoff valve (see step 1
below). Then remove the shutoff valve from the cover plate (4 screws outside fireplace). The pipe may be routed
through the cover plate and the shutoff valve and gas line may be re-attached inside the fireplace.
Gas line may be plumbed from the left side (stock) or below. See illustration and table below to determine gas line location.
a b
Left Side Gas Line Location (Stock) 6-7/8” (175mm) 4-1/8” (105mm)
Baseplate Gas Line Location 6-3/4” (172mm) 26-3/4” (680mm)
Relocating the Gas Line to the Baseplate
1. Disconnect the gas line from the shutoff valve (3/4” wrench). Gas line is located inside the fireplace on the left side.
2. Remove the screw that holds the shutoff valve plate in place (1/4” nutdriver). Remove the shutoff valve plate.
3. Remove the cover plate from the bottom of the fireplace (it is held in place in the same fashion as the shutoff valve plate).
Attach it to the left side of the fireplace.
4. Attach the shutoff valve plate to the bottom of the fireplace. Route the gas line to the bottom and re-attach the gas line to
the shutoff valve. Make sure to leak test the entire gas line.