Draper 56407 User manual

Draper Tools Limited, Hursley Road,
Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: [phone]
Sales Desk: [phone]
Internet: drapertools.com
E-mail: [email protected]
General Enquiries: [phone]
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the
Draper Tools Helpline for details of an agent in your local area.
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
CONTACTS
YOUR DRAPER STOCKIST
TAPR0621
These instructions accompanying the product are the original instructions. This document is part of the product, keep
it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.

230V 7KG
SDS MAX ROTARY
HAMMER DRILL
56407

1. TITLE PAGE
1.1 INTRODUCTION:
USER MANUAL FOR: 230V 7kg SDS MAX Rotary Hammer Drill
Stock No: 56407
Part No: SDSMAXHD1600E
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://drapertools.com/manuals
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product Helpline: [phone]
General Fax: [phone]
1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT:
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use
only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any
other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
1.2 REVISIONS:
Date first published August 2018.
- 19 -
NOTES

2. CONTENTS
1 TITLE PAGE
1.1 INTRODUCTION ............................................................................................................ 2
1.2 REVISION HISTORY ...................................................................................................... 2
1.3 UNDERSTANDING THIS MANUAL ...............................................................................2
1.4 COPYRIGHT NOTICE.....................................................................................................2
2 CONTENTS
2.1 CONTENTS.....................................................................................................................3
3 GUARANTEE
3.1 GUARANTEE .................................................................................................................. 4
4 INTRODUCTION
4.1 SCOPE ........................................................................................................................... 5
4.2 SPECIFICATION .............................................................................................................5
4.3 HANDLING & STORAGE................................................................................................ 5
5 HEALTH & SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS ............................................................................6
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR HAMMER DRILLS ..................................... 7
5.3 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS................................. 7
5.4 RESIDUAL RISK ............................................................................................................. 8
5.5 CONNECTION TO THE POWER SUPPLY..................................................................... 8
6 TECHNICAL DESCRIPTION
6.1 IDENTIFICATION ............................................................................................................9
7 UNPACKING & CHECKING
7.1 PACKAGING .................................................................................................................10
7.2 WHAT’S IN THE BOX.................................................................................................... 10
8 PREPARING THE DRILL
8.1 AUXILIARY HANDLE .................................................................................................... 11
9 BASIC HAMMER DRILL OPERATIONS
9.1 FUNCTION SELECTORS ............................................................................................. 12
9.2 PNEUMATIC HAMMER DRILLING ............................................................................... 13
9.3 PNEUMATIC CHISELLING ...........................................................................................13
9.4 ROTATIONAL CHISEL SELECTION.............................................................................13
9.5 TRIGGER SWITCH....................................................................................................... 13
9.6 SDS MAX SYSTEM ......................................................................................................14
9.7 DUST AND SWARF ...................................................................................................... 14
9.8 DRILLING WOOD, PLASTIC AND METAL ................................................................... 14
10 MAINTENANCE
10.1 GEARBOX MAINTENANCE .........................................................................................15
10.2 OPTIONAL ACCESSORIES..........................................................................................15
11 TROUBLESHOOTING
11.1 TROUBLESHOOTING GUIDE...................................................................................... 16
12 DISPOSAL
12.1 DISPOSAL.....................................................................................................................17
13 EXPLANATION OF SYMBOLS
13.1 EXPLANATION OF SYMBOLS .....................................................................................18
14 DISPOSAL
14.1 DISPOSAL.....................................................................................................................18
DECLARATION OF CONFORMITY .............................................................................. ENCLOSED
- 3 -
- 18 -
13.1 EXPLANATION OF SYMBOLS
13. EXPLANATION OF SYMBOLS
WEEE –
Waste Electrical &
Electronic Equipment.
Do not dispose of Waste Electrical
& Electronic Equipment in with
domestic rubbish.
Class II construction
(Double insulated).
Read the instruction manual.
Wear face mask and safety
glasses.
Wear ear defenders.
Wear protective gloves.
Do not abandon into the
environment.
Keep out of the reach of children.
Warning!
1. TITLE PAGE
1.1 INTRODUCTION:
USER MANUAL FOR: 230V 7kg SDS MAX Rotary Hammer Drill
Stock No: 56407
Part No: SDSMAXHD1600E
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://drapertools.com/manuals
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product Helpline: [phone]
General Fax: [phone]
1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT:
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use
only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any
other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
1.2 REVISIONS:
Date first published August 2018.
- 19 -
NOTES

- 17 -
3. WARRANTY
- 4 -
3.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or contact:
Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: [phone] or:
Product Helpline [phone].
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This warranty period covering labour is 12 months from
the date of purchase except where tools are hired out when the warranty period is 90 days from
the date of purchase. The warranty is extended to 24 months from the date of purchase for parts
only. This warranty does not apply to any consumable parts, any type of battery or normal wear
and tear, nor does it cover any damage caused by misuse, careless or unsafe handling,
alterations, accidents, or repairs attempted or made by any personnel other than the authorised
Draper warranty repair agent.
Draper Tools Limited takes pride in the quality of its products and the services offered to our
valued customers. As a result we offer a free, 3 year extended warranty for this product.
REGISTER WITHIN 30 DAYS TO CLAIM YOUR
*To register your warranty, visit: drapertools.com/warranty-registration
or call our Customer Helpline on: [phone]
By registering your product you’ll automatically become a Draper Club Member where you will
have the option to receive news of our new products, offers, deals, competitions and more!
If you are unable to register online, please call our Customer Helpline on the number shown above.
Full registration must be completed within 30 days from receipt of purchase. The 3 year extended
warranty only applies to permanent UK residents, to the original product purchased from an
authorised Draper Tools stockist for use in their appropriate profession/trade. This warranty is not
valid to purchasers reselling or hiring the product. This warranty is not transferable and is only
available to the original product purchaser who has completed their registration and is a Draper
Club Member. The 3 year extended warranty period starts from the date of purchase and is not
extended following an inspection, repair or replacement.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms
are not authorised.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
For full terms and conditions visit: drapertools.com/corporate-policies
FREE
12. DISPOSAL
12.1 DISPOSAL
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:
● Do not dispose of power tools with domestic waste.
● Do not incinerate.
● Do not dispose of WEEE* as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.

- 17 -
3. WARRANTY
- 4 -
3.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or contact:
Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: [phone] or:
Product Helpline [phone].
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This warranty period covering labour is 12 months from
the date of purchase except where tools are hired out when the warranty period is 90 days from
the date of purchase. The warranty is extended to 24 months from the date of purchase for parts
only. This warranty does not apply to any consumable parts, any type of battery or normal wear
and tear, nor does it cover any damage caused by misuse, careless or unsafe handling,
alterations, accidents, or repairs attempted or made by any personnel other than the authorised
Draper warranty repair agent.
Draper Tools Limited takes pride in the quality of its products and the services offered to our
valued customers. As a result we offer a free, 3 year extended warranty for this product.
REGISTER WITHIN 30 DAYS TO CLAIM YOUR
*To register your warranty, visit: drapertools.com/warranty-registration
or call our Customer Helpline on: [phone]
By registering your product you’ll automatically become a Draper Club Member where you will
have the option to receive news of our new products, offers, deals, competitions and more!
If you are unable to register online, please call our Customer Helpline on the number shown above.
Full registration must be completed within 30 days from receipt of purchase. The 3 year extended
warranty only applies to permanent UK residents, to the original product purchased from an
authorised Draper Tools stockist for use in their appropriate profession/trade. This warranty is not
valid to purchasers reselling or hiring the product. This warranty is not transferable and is only
available to the original product purchaser who has completed their registration and is a Draper
Club Member. The 3 year extended warranty period starts from the date of purchase and is not
extended following an inspection, repair or replacement.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms
are not authorised.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
For full terms and conditions visit: drapertools.com/corporate-policies
FREE
12. DISPOSAL
12.1 DISPOSAL
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:
● Do not dispose of power tools with domestic waste.
● Do not incinerate.
● Do not dispose of WEEE* as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.
4. INTRODUCTION
4.1 SCOPE
For impact drilling/chiselling into brick, concrete and stone.
This product is intended for trade use and has the quality and features to meet and exceed the
expectations of the most demanding user. Any application other than that it was intended for, is
considered misuse.
4.2 SPECIFICATION
Stock no. ................................................................................................................................ 56407
Part no. .............................................................................................................. SDSMAXHD1600E
Rated voltage ................................................................................................................ 230V~50Hz
Rated input ............................................................................................................................ 1600W
Core drill capacity..................................................................................................................... 90mm
Note: This machine has a clutch so is suitable for occasional core drilling. It is not a dedicated
core drilling machine and must not be used as such.
Drilling capacity:
Masonry ......................................................................................................................... 40mm
Note: This figure is derived using a defined mix of concrete and as such, your material may be
harder or softer than the material, so a degree of leeway should be applied to this figure. A window
lintel for example will be much harder than the test concrete and this machine will not be able to
reach the same level of performance when compared to a softer mix of concrete.
Impact force...........................................................................................................................9 Joules
Revolutions per minute (no load) ....................................................................................... 560r/min
Impact rate ...................................................................................................................... 3530b/min
Chuck type ....................................................................................................................... SDS MAX
Sound pressure level* .............................................................................................. 93.9dB +/- 3dB
Sound power level** ............................................................................................... 104.9dB +/- 3dB
Vibration level:
hammer drilling into concrete ................................................................13.550m/s² +/- 1.5m/s2
chiselling................................................................................................ 12.299m/s² +/- 1.5m/s2
Weight (drill only)......................................................................................................................... 7kg
4.3 HANDLING & STORAGE
– Care must be taken when handling this product.
● Dropping this power tool could have an effect on its accuracy and could also result in
personal injury. This product is not a toy and must be respected.
– Environmental conditions can have a detrimental effect on this product if neglected.
● Exposure to damp air can gradually corrode components.
● If the product is unprotected from dust and debris, components will become clogged.
● If not cleaned and maintained correctly or regularly, the machine will not perform at its best.
* Continuous A-Weighted sound pressure level at the workstation in accordance to and declared
according to EN60745.
** The typical A-Weighted noise level determined according to EN60745.
- 5 -
11. TROUBLESHOOTING
11.1 TROUBLESHOOTING GUIDE
Note: Remove the plug from the socket before carrying out adjustment, servicing or maintenance.
- 16 -
Problem Possible Cause Remedy
Motor does not start. 1. Fuse.
3. Unsure.
1. Replace/reset 13 amp time
delay fuse or circuit breaker.
2. Have carbon brushes
replaced in motor.
3. Return to an authorised
service agent for diagnosis.
2. Brushes worn.

5. HEALTH AND SAFETY INFORMATION
When using any type of power tool there are steps that should be taken to make sure that you, as
the user, remain safe.
Common sense and a respect for the tool will help reduce the risk of injury.
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
Warning!
● Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
● The term “power tool” in the warnings refers to your mains operated (corded) power tool or
battery-operated (cordless) power tool.
Most important: You must know how to safely start and stop this machine, especially in an
emergency.
Keep the work area tidy and clean. Attempting to clear clutter from around the machine during use
will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilled on the floor
could result in you slipping.
Find a suitable location. If the machine is bench mounted, the location should provide good natural
light or artificial lighting as a replacement. Avoid damp and dusty locations as it will have a negative
effect on the machine’s performance. If the machine is portable do not expose the tool to rain. In all
cases do not operate power tools near any flammable materials.
Keep bystanders away. Children, onlookers and passers by must be restricted from entering the
work area for their own protection. The barrier must extend a suitable distance from the tool user.
Unplug and house all power tools that are not in use. A power tool should never be left unattended
while connected to the power supply. They must be housed in a suitable location, away locked up
and from children.
Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what
they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an
application it is not designed for. Select a tool appropriate for the size of the job. Overloading a tool
will result in tool failure and user injury. This covers the use of accessories.
Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can become
entangled in moving machinery. This can also result in parts of body being pulled into the machine.
Clothing should be close fitted, with any long hair tired back and jewellery and neck ties removed.
Footwear must be fully enclosed and have a non-slip sole.
Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be dangerous
if not suitably protected against. If the work involving the power tool creates dust or fumes wear a
dust mask. Vibration to the hand, caused by operating some tools for longer periods must be
protected against. Wear vibration reducing gloves and allow long breaks between uses. Protect
against dust and swarf by wearing approved safety goggles or a face shield. These are some of the
more common hazards and preventions, however, always find out what hazards are associated with
the machine/work process and wear the most suitable protective equipment available.
Do not breathe contaminated air. If the work creates dust or fumes connect the machine
(if possible) to an extraction system either locally or remotely. Working outdoors can also help
if possible.
Move the machine as instructed. If the machine is hand held, do not carry it by the power supply
cable. If the product is heavy, employ a second or third person to help move it safely or use a
mechanical device. Always refer to the instructions for the correct method.
Do not overreach. Extending your body too far can result in a loss of balance and you falling.
This could be from a height or onto a machine and will result in injury.
Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged
or missing parts immediately with original parts from the manufacturer. As applicable keep blades
sharp, moving parts clean, oiled or greased, handles clean and emergency devices working.
- 6 -
10. MAINTENANCE
10.1 GEARBOX MAINTENANCE – FIG. 14
Note: Remove the plug from the socket before
carrying out adjustment, servicing or maintenance.
– Before each use remove the gearbox access
cover
(4) to ensure there is sufficient grease.
– Using pin spanner
(9) remove the access cover
(4) anti-clockwise.
– If required top-up the gearbox (20 grams max.)
using a general purpose lithium based grease.
– Lubricating the SDS MAX drill bit before
inserting into the SDS MAX chuck is advisable.
Warning! Assembly must be completed prior to
operating the machine.
The hammer drill does not require any special maintenance. Regularly clean/vacuum the
ventilation slots. Use only a mild cleaner and a damp cloth to clean the tool.
10.2 OPTIONAL ACCESSORIES
For a full range of optional accessories, please refer to your local Draper Stockist.
- 15 -
FIG.14
(9)
(4)

5. HEALTH AND SAFETY INFORMATION
Wait for the machine to stop. Unless the machine is fitted with a safety brake, some parts may
continue to move due to momentum. Wait for all parts to stop, then unplug it from the power supply
before making any adjustments, carrying out maintenance operations or just finishing using the tool.
Remove and check setting tools. Some machinery requires the use of additional tools or keys to
set, load or adjust the power tool. Before starting the power tool always check to make certain they
have been removed and are safely away from the machine.
Prevent unintentional starting. Before plugging any machine in to the power supply, make sure the
switch is in the OFF position. If the machine is portable, do not hold the machine near the switch and
take care when putting the machine down, that nothing can operate the switch.
Carefully select an extension lead. Some machines are not suitable for use with extension leads. If
the tool is designed for use outdoors, use an extension lead also suitable for that environment. When
using an extended lead, select one capable of handling the current (amps) drawn by the machine in
use. Fully extend the lead regardless of the distance between the power supply and the tool. Excess
current (amps) and a coiled extension lead will both cause the cable to heat up and can result in fire.
Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power tool
if you are under the influence of drugs (prescription or otherwise), including alcohol or if you are
feeling tired. Being disorientated will result in an accident.
Have this tool repaired by a qualified person. This tool is designed to conform to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified, using only original parts supplied by the manufacturer. This will ensure the tool remains
safe to use.
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR HAMMER DRILLS
– Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
– Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
– Hold power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a
“live” wire may make exposed metal parts of the power tool “live” and could give the operator
an electric shock.
5.3 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS
Important: Draper Tools Limited recommends that this machine should not be modified or used
for any application other than that for which it was designed. If you are unsure of its relative
applications do not hesitate to contact us in writing and we will advise you.
– Power tools shall not be used in potentially explosive atmospheres unless specifically designed
for that purpose.
– Unexpected tool movement due to reaction forces or breakage may cause injuries.
– Power tools shall be isolated from the energy source before changing or adjusting the
inserted tool.
Warning!
● Wear appropriate ear protection. Exposure to noise can lead to hearing loss.
● There is a risk of loose clothing, hair etc., being caught in the rotating spindle of the
power tool.
- 7 -
- 14 -
(3)
9. BASIC HAMMER DRILL OPERATIONS
9.6 SDS MAX SYSTEM – FIGS. 10 – 11
The tool holder (2.2) clamps SDS MAX drill bits and
chisels without the need for a chuck key.
– Pull collar
(2.3) back.
– Insert the bit. It may be necessary to rotate the
bit to ensure it engages correctly.
– Release the collar to lock the bit in place. Check
by pulling the bit to see if it’s firmly seated.
Important: Always clean and lightly grease the tool
shaft before inserting into the chuck.
Take care that the dust protection cap is not
damaged. Allowing dust and debris inside the
holder will cause problems in the future.
– To remove a bit, slide the collar
(2.3) to the rear
and pull out the tool.
Warning! Bit will be hot after use.
9.7 DUST AND SWARF:
A correctly fitted dusk mask, suitable for the activity
and in accordance to the relevant standard, must
be worn.
For work activities involving exposure to fine wood
dust, a mask rated to at least FFP2 should be used.
Swarf produced by metal drilling is extremely sharp.
Take precautions when clearing swarf. The burr left
on the hole is also sharp and should be removed
with a suitable tool.
9.8 DRILLING WOOD, PLASTIC OR
METAL
Although technically possible, Draper do not
recommend the use of this machine for drilling into
wood, metal or plastic. This machine is designed for
drilling through brick and concrete and is
engineered to do so, this makes it an unwieldy
machine to drill wood, metal or plastic and there are
tools that are far more capable of doing the job with
a greater degree of control.
FIG.10
FIG.11
(2.2)
(2.2)
(2.3)
(2.3)
5. HEALTH AND SAFETY INFORMATION
When using any type of power tool there are steps that should be taken to make sure that you, as
the user, remain safe.
Common sense and a respect for the tool will help reduce the risk of injury.
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
Warning!
● Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
● The term “power tool” in the warnings refers to your mains operated (corded) power tool or
battery-operated (cordless) power tool.
Most important: You must know how to safely start and stop this machine, especially in an
emergency.
Keep the work area tidy and clean. Attempting to clear clutter from around the machine during use
will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilled on the floor
could result in you slipping.
Find a suitable location. If the machine is bench mounted, the location should provide good natural
light or artificial lighting as a replacement. Avoid damp and dusty locations as it will have a negative
effect on the machine’s performance. If the machine is portable do not expose the tool to rain. In all
cases do not operate power tools near any flammable materials.
Keep bystanders away. Children, onlookers and passers by must be restricted from entering the
work area for their own protection. The barrier must extend a suitable distance from the tool user.
Unplug and house all power tools that are not in use. A power tool should never be left unattended
while connected to the power supply. They must be housed in a suitable location, away locked up
and from children.
Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what
they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an
application it is not designed for. Select a tool appropriate for the size of the job. Overloading a tool
will result in tool failure and user injury. This covers the use of accessories.
Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can become
entangled in moving machinery. This can also result in parts of body being pulled into the machine.
Clothing should be close fitted, with any long hair tired back and jewellery and neck ties removed.
Footwear must be fully enclosed and have a non-slip sole.
Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be dangerous
if not suitably protected against. If the work involving the power tool creates dust or fumes wear a
dust mask. Vibration to the hand, caused by operating some tools for longer periods must be
protected against. Wear vibration reducing gloves and allow long breaks between uses. Protect
against dust and swarf by wearing approved safety goggles or a face shield. These are some of the
more common hazards and preventions, however, always find out what hazards are associated with
the machine/work process and wear the most suitable protective equipment available.
Do not breathe contaminated air. If the work creates dust or fumes connect the machine
(if possible) to an extraction system either locally or remotely. Working outdoors can also help
if possible.
Move the machine as instructed. If the machine is hand held, do not carry it by the power supply
cable. If the product is heavy, employ a second or third person to help move it safely or use a
mechanical device. Always refer to the instructions for the correct method.
Do not overreach. Extending your body too far can result in a loss of balance and you falling.
This could be from a height or onto a machine and will result in injury.
Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged
or missing parts immediately with original parts from the manufacturer. As applicable keep blades
sharp, moving parts clean, oiled or greased, handles clean and emergency devices working.
- 6 -
10. MAINTENANCE
10.1 GEARBOX MAINTENANCE – FIG. 14
Note: Remove the plug from the socket before
carrying out adjustment, servicing or maintenance.
– Before each use remove the gearbox access
cover
(4) to ensure there is sufficient grease.
– Using pin spanner
(9) remove the access cover
(4) anti-clockwise.
– If required top-up the gearbox (20 grams max.)
using a general purpose lithium based grease.
– Lubricating the SDS MAX drill bit before
inserting into the SDS MAX chuck is advisable.
Warning! Assembly must be completed prior to
operating the machine.
The hammer drill does not require any special maintenance. Regularly clean/vacuum the
ventilation slots. Use only a mild cleaner and a damp cloth to clean the tool.
10.2 OPTIONAL ACCESSORIES
For a full range of optional accessories, please refer to your local Draper Stockist.
- 15 -
FIG.14
(9)
(4)

5. HEALTH AND SAFETY INFORMATION
● Do not touch the drill bit or areas close to the drill bit immediately after use; they can still
be extremely hot, causing burns.
– Be sure the drill bit is securely in place before using the drill.
– There is a risk of release of toxic chemicals into the atmosphere when using certain materials.
Always be mindful to use the appropriate personal protective wear to help safeguard against
potential skin contact and dust inhalation. Always consult and follow the material supplier’s
safety guidelines.
– Adopt a suitable posture to counteract normal or unexpected movement of the power tool due
to reaction forces from the power assembly tool.
– Do not modify this drill driver in any way. Any other application is considered misuse and will
invalidate the warranty.
5.4 RESIDUAL RISK
Important note: Although the safety instructions and operating manuals for our tools contain
extensive instructions of safe working with power tools, every power tool involves a certain
residual risk which can not be completely excluded by safety mechanisms. Power tools must
therefore always be operated with caution!
5.5 CONNECTION TO THE POWER SUPPLY
Caution: Risk of electric shock. Do not open.
This appliance is supplied with a moulded 3 pin mains plug for your safety. The value of the fuse
fitted is marked on the pin face of the plug. Should the fuse need replacing, ensure the substitute
is of the correct rating, approved to BS1362 and ASTA or BS Kite marked.
ASTA
BSI
The fuse cover is removable with a small plain slot screwdriver. Ensure the fuse cover is replaced
before attempting to connect the plug to an electrical outlet. If the cover is missing, a replacement
must be obtained or the plug replaced with a suitable type.
If a replacement plug is to be fitted this must be carried out by a qualified electrician.
The damaged or incomplete plug, when cut from the cable should be disabled to prevent
connection to a live electrical outlet.
This appliance is Class II† and is designed for connection to a power supply matching that
detailed on the rating label and compatible with the plug fitted.
If an extension lead is required, use an approved and compatible lead rated for this appliance.
Follow all the instructions supplied with the extension lead.
†Double insulated : This product requires no earth connection as supplementary insulation
is applied to the basic insulation to protect against electric shock in the event of failure of the
basic insulation.
IMPORTANT
If using an extension lead, follow the instructions that came with your lead regarding maximum
load while cable is wound. If in doubt, ensure that the entire cable is unwound. Using a coiled
extension lead will generate heat which could melt the lead and cause a fire.
- 8 -
- 13 -
(3)
9. BASIC HAMMER DRILL OPERATIONS
9.2 PNEUMATIC HAMMER DRILLING
– FIG. 5
With the drill at standstill:
– Position the rotary/ hammer selection dial
(7) to
the right.
This set-up is for masonry drilling i.e. into brick,
concrete, block work, etc.
9.3 PNEUMATIC CHISELLING – FIG. 6
With the drill at standstill:
– Position the rotary/ hammer selection dial
(7) to
the left.
This set-up is for chiselling with the chuck rotation
stop engaged i.e. chiselling/chasing out brickwork,
plasterboard, etc.
9.4 ROTATIONAL CHISEL SELECTION
– FIG. 6
– To ensure the chisel is facing in the correct
direction to the workpiece to be chiselled, rotate
the selection dial to the • position. Manually
adjust the chisel to the desired angle, then
rotate selection dial
(7) back to hammer
function.
9.5 TRIGGER SWITCH – FIG. 6
Select the required function.
– Pull trigger
(5) to activate the machine.
FIG.5
FIG.6
FIG.7
(7)
(7)
(5)

6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION
- 9 -
(1) Auxiliary handle.
(2) SDS MAX chuck.
(3) Rotary/hammer selector.
(4) Gearbox access cover.
(5) On/Off trigger switch.
(6) Hand grip.
(7) Power ON indicator.
(8) Plug & cable.
9. BASIC HAMMER DRILL OPERATIONS
- 12 -
(3) (4) (5)
(8)
(7)
(6)
(1)
(2)
FIG.2
FIG.3
FIG.4
(3)
(1)
(1)
(3)
(3)
Warning! Prior to beginning any drilling,
carefully check the surface for the presence
of electric cable, gas or water pipes and
other dangerous or damaging contents.
If unsure do not proceed.
Note: Remove the plug from the socket
before carrying out adjustment, servicing
or maintenance.
9.1 FUNCTION SELECTORS –
FIGS. 2 – 5
Rotary/Hammer selector (3)
FIG.2: Rotary Drill.
FIG.3: Hammer Drill.
Note: To change function you must first
depress the function lock
(1) before turning
the rotary/hammer selector.
Rotational chisel selection (3)
FIG.4: Rotational chisel selection.

8. PREPARING THE DRILL
7. UNPACKING AND CHECKING
Note: Remove the plug from the socket before
carrying out adjustment, servicing or maintenance.
8.1 AUXILIARY HANDLE – FIG. 1
Warning! Use auxiliary handle supplied with the
tool. Loss of control can cause personal injury.
When fitting the auxiliary handle
(1) :
– Ensure the hand grip is loose (screw
anti-clockwise to loosen) before sliding it over
the drill’s chuck onto the collar
(2.1) .
– Select the required angle of the handle and
tighten the handgrip to secure.
7.1 PACKAGING
Carefully remove the product from the packaging and examine it for any sign of damage that may
have happened during shipping. Lay the contents out and check them against the parts shown
below. If any part is damaged or missing; please contact the Draper Help Line (the telephone
number appears on the Title page) and do not attempt to use the product.
The packaging material should be retained at least during the guarantee period: in case the
machine needs to be returned for repair.
Warning! Some of the packaging materials used may be harmful to children. Do not leave any of
these materials in the reach of children.
If any of the packaging is to be thrown away, make sure they are disposed of correctly; according
to local regulations.
7.2 WHAT’S IN THE BOX
As well as the rotary hammer drill, there are several parts not fitted or attached to it.
(1) Auxiliary handle.
(9) 2 pin spanner.
(10) Grease.
(11) Brushes.
(12) 320mm Long x 18mmø SDS MAX drill bit.
(13) 320mm Long SDS MAX pointed chisel.
- 10 -
- 11 -
(9) (10)
(11)
(1)
(12)
(13)
FIG.1
(1)
(2.1)

8. PREPARING THE DRILL
7. UNPACKING AND CHECKING
Note: Remove the plug from the socket before
carrying out adjustment, servicing or maintenance.
8.1 AUXILIARY HANDLE – FIG. 1
Warning! Use auxiliary handle supplied with the
tool. Loss of control can cause personal injury.
When fitting the auxiliary handle
(1) :
– Ensure the hand grip is loose (screw
anti-clockwise to loosen) before sliding it over
the drill’s chuck onto the collar
(2.1) .
– Select the required angle of the handle and
tighten the handgrip to secure.
7.1 PACKAGING
Carefully remove the product from the packaging and examine it for any sign of damage that may
have happened during shipping. Lay the contents out and check them against the parts shown
below. If any part is damaged or missing; please contact the Draper Help Line (the telephone
number appears on the Title page) and do not attempt to use the product.
The packaging material should be retained at least during the guarantee period: in case the
machine needs to be returned for repair.
Warning! Some of the packaging materials used may be harmful to children. Do not leave any of
these materials in the reach of children.
If any of the packaging is to be thrown away, make sure they are disposed of correctly; according
to local regulations.
7.2 WHAT’S IN THE BOX
As well as the rotary hammer drill, there are several parts not fitted or attached to it.
(1) Auxiliary handle.
(9) 2 pin spanner.
(10) Grease.
(11) Brushes.
(12) 320mm Long x 18mmø SDS MAX drill bit.
(13) 320mm Long SDS MAX pointed chisel.
- 10 -
- 11 -
(9) (10)
(11)
(1)
(12)
(13)
FIG.1
(1)
(2.1)

6. TECHNICAL DESCRIPTION
6.1 IDENTIFICATION
- 9 -
(1) Auxiliary handle.
(2) SDS MAX chuck.
(3) Rotary/hammer selector.
(4) Gearbox access cover.
(5) On/Off trigger switch.
(6) Hand grip.
(7) Power ON indicator.
(8) Plug & cable.
9. BASIC HAMMER DRILL OPERATIONS
- 12 -
(3) (4) (5)
(8)
(7)
(6)
(1)
(2)
FIG.2
FIG.3
FIG.4
(3)
(1)
(1)
(3)
(3)
Warning! Prior to beginning any drilling,
carefully check the surface for the presence
of electric cable, gas or water pipes and
other dangerous or damaging contents.
If unsure do not proceed.
Note: Remove the plug from the socket
before carrying out adjustment, servicing
or maintenance.
9.1 FUNCTION SELECTORS –
FIGS. 2 – 5
Rotary/Hammer selector (3)
FIG.2: Rotary Drill.
FIG.3: Hammer Drill.
Note: To change function you must first
depress the function lock
(1) before turning
the rotary/hammer selector.
Rotational chisel selection (3)
FIG.4: Rotational chisel selection.

5. HEALTH AND SAFETY INFORMATION
● Do not touch the drill bit or areas close to the drill bit immediately after use; they can still
be extremely hot, causing burns.
– Be sure the drill bit is securely in place before using the drill.
– There is a risk of release of toxic chemicals into the atmosphere when using certain materials.
Always be mindful to use the appropriate personal protective wear to help safeguard against
potential skin contact and dust inhalation. Always consult and follow the material supplier’s
safety guidelines.
– Adopt a suitable posture to counteract normal or unexpected movement of the power tool due
to reaction forces from the power assembly tool.
– Do not modify this drill driver in any way. Any other application is considered misuse and will
invalidate the warranty.
5.4 RESIDUAL RISK
Important note: Although the safety instructions and operating manuals for our tools contain
extensive instructions of safe working with power tools, every power tool involves a certain
residual risk which can not be completely excluded by safety mechanisms. Power tools must
therefore always be operated with caution!
5.5 CONNECTION TO THE POWER SUPPLY
Caution: Risk of electric shock. Do not open.
This appliance is supplied with a moulded 3 pin mains plug for your safety. The value of the fuse
fitted is marked on the pin face of the plug. Should the fuse need replacing, ensure the substitute
is of the correct rating, approved to BS1362 and ASTA or BS Kite marked.
ASTA
BSI
The fuse cover is removable with a small plain slot screwdriver. Ensure the fuse cover is replaced
before attempting to connect the plug to an electrical outlet. If the cover is missing, a replacement
must be obtained or the plug replaced with a suitable type.
If a replacement plug is to be fitted this must be carried out by a qualified electrician.
The damaged or incomplete plug, when cut from the cable should be disabled to prevent
connection to a live electrical outlet.
This appliance is Class II† and is designed for connection to a power supply matching that
detailed on the rating label and compatible with the plug fitted.
If an extension lead is required, use an approved and compatible lead rated for this appliance.
Follow all the instructions supplied with the extension lead.
†Double insulated : This product requires no earth connection as supplementary insulation
is applied to the basic insulation to protect against electric shock in the event of failure of the
basic insulation.
IMPORTANT
If using an extension lead, follow the instructions that came with your lead regarding maximum
load while cable is wound. If in doubt, ensure that the entire cable is unwound. Using a coiled
extension lead will generate heat which could melt the lead and cause a fire.
- 8 -
- 13 -
(3)
9. BASIC HAMMER DRILL OPERATIONS
9.2 PNEUMATIC HAMMER DRILLING
– FIG. 5
With the drill at standstill:
– Position the rotary/ hammer selection dial
(7) to
the right.
This set-up is for masonry drilling i.e. into brick,
concrete, block work, etc.
9.3 PNEUMATIC CHISELLING – FIG. 6
With the drill at standstill:
– Position the rotary/ hammer selection dial
(7) to
the left.
This set-up is for chiselling with the chuck rotation
stop engaged i.e. chiselling/chasing out brickwork,
plasterboard, etc.
9.4 ROTATIONAL CHISEL SELECTION
– FIG. 6
– To ensure the chisel is facing in the correct
direction to the workpiece to be chiselled, rotate
the selection dial to the • position. Manually
adjust the chisel to the desired angle, then
rotate selection dial
(7) back to hammer
function.
9.5 TRIGGER SWITCH – FIG. 6
Select the required function.
– Pull trigger
(5) to activate the machine.
FIG.5
FIG.6
FIG.7
(7)
(7)
(5)

5. HEALTH AND SAFETY INFORMATION
Wait for the machine to stop. Unless the machine is fitted with a safety brake, some parts may
continue to move due to momentum. Wait for all parts to stop, then unplug it from the power supply
before making any adjustments, carrying out maintenance operations or just finishing using the tool.
Remove and check setting tools. Some machinery requires the use of additional tools or keys to
set, load or adjust the power tool. Before starting the power tool always check to make certain they
have been removed and are safely away from the machine.
Prevent unintentional starting. Before plugging any machine in to the power supply, make sure the
switch is in the OFF position. If the machine is portable, do not hold the machine near the switch and
take care when putting the machine down, that nothing can operate the switch.
Carefully select an extension lead. Some machines are not suitable for use with extension leads. If
the tool is designed for use outdoors, use an extension lead also suitable for that environment. When
using an extended lead, select one capable of handling the current (amps) drawn by the machine in
use. Fully extend the lead regardless of the distance between the power supply and the tool. Excess
current (amps) and a coiled extension lead will both cause the cable to heat up and can result in fire.
Concentrate and stay alert. Distractions are likely to cause an accident. Never operate a power tool
if you are under the influence of drugs (prescription or otherwise), including alcohol or if you are
feeling tired. Being disorientated will result in an accident.
Have this tool repaired by a qualified person. This tool is designed to conform to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified, using only original parts supplied by the manufacturer. This will ensure the tool remains
safe to use.
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR HAMMER DRILLS
– Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
– Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
– Hold power tool by insulated gripping surfaces, when performing an operation where the
cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a
“live” wire may make exposed metal parts of the power tool “live” and could give the operator
an electric shock.
5.3 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS
Important: Draper Tools Limited recommends that this machine should not be modified or used
for any application other than that for which it was designed. If you are unsure of its relative
applications do not hesitate to contact us in writing and we will advise you.
– Power tools shall not be used in potentially explosive atmospheres unless specifically designed
for that purpose.
– Unexpected tool movement due to reaction forces or breakage may cause injuries.
– Power tools shall be isolated from the energy source before changing or adjusting the
inserted tool.
Warning!
● Wear appropriate ear protection. Exposure to noise can lead to hearing loss.
● There is a risk of loose clothing, hair etc., being caught in the rotating spindle of the
power tool.
- 7 -
- 14 -
(3)
9. BASIC HAMMER DRILL OPERATIONS
9.6 SDS MAX SYSTEM – FIGS. 10 – 11
The tool holder (2.2) clamps SDS MAX drill bits and
chisels without the need for a chuck key.
– Pull collar
(2.3) back.
– Insert the bit. It may be necessary to rotate the
bit to ensure it engages correctly.
– Release the collar to lock the bit in place. Check
by pulling the bit to see if it’s firmly seated.
Important: Always clean and lightly grease the tool
shaft before inserting into the chuck.
Take care that the dust protection cap is not
damaged. Allowing dust and debris inside the
holder will cause problems in the future.
– To remove a bit, slide the collar
(2.3) to the rear
and pull out the tool.
Warning! Bit will be hot after use.
9.7 DUST AND SWARF:
A correctly fitted dusk mask, suitable for the activity
and in accordance to the relevant standard, must
be worn.
For work activities involving exposure to fine wood
dust, a mask rated to at least FFP2 should be used.
Swarf produced by metal drilling is extremely sharp.
Take precautions when clearing swarf. The burr left
on the hole is also sharp and should be removed
with a suitable tool.
9.8 DRILLING WOOD, PLASTIC OR
METAL
Although technically possible, Draper do not
recommend the use of this machine for drilling into
wood, metal or plastic. This machine is designed for
drilling through brick and concrete and is
engineered to do so, this makes it an unwieldy
machine to drill wood, metal or plastic and there are
tools that are far more capable of doing the job with
a greater degree of control.
FIG.10
FIG.11
(2.2)
(2.2)
(2.3)
(2.3)

5. HEALTH AND SAFETY INFORMATION
When using any type of power tool there are steps that should be taken to make sure that you, as
the user, remain safe.
Common sense and a respect for the tool will help reduce the risk of injury.
5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE
Warning!
● Read all safety warnings and all instructions. Failure to follow the warnings and instructions
may result in electric shock, fire and/or serious injury.
● The term “power tool” in the warnings refers to your mains operated (corded) power tool or
battery-operated (cordless) power tool.
Most important: You must know how to safely start and stop this machine, especially in an
emergency.
Keep the work area tidy and clean. Attempting to clear clutter from around the machine during use
will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilled on the floor
could result in you slipping.
Find a suitable location. If the machine is bench mounted, the location should provide good natural
light or artificial lighting as a replacement. Avoid damp and dusty locations as it will have a negative
effect on the machine’s performance. If the machine is portable do not expose the tool to rain. In all
cases do not operate power tools near any flammable materials.
Keep bystanders away. Children, onlookers and passers by must be restricted from entering the
work area for their own protection. The barrier must extend a suitable distance from the tool user.
Unplug and house all power tools that are not in use. A power tool should never be left unattended
while connected to the power supply. They must be housed in a suitable location, away locked up
and from children.
Do not overload or misuse the tool. All tools are designed for a purpose and are limited to what
they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an
application it is not designed for. Select a tool appropriate for the size of the job. Overloading a tool
will result in tool failure and user injury. This covers the use of accessories.
Dress properly. Loose clothing, long hair and jewellery are all dangerous because they can become
entangled in moving machinery. This can also result in parts of body being pulled into the machine.
Clothing should be close fitted, with any long hair tired back and jewellery and neck ties removed.
Footwear must be fully enclosed and have a non-slip sole.
Wear personal protective equipment (PPE). Dust, noise, vibration and swarf can all be dangerous
if not suitably protected against. If the work involving the power tool creates dust or fumes wear a
dust mask. Vibration to the hand, caused by operating some tools for longer periods must be
protected against. Wear vibration reducing gloves and allow long breaks between uses. Protect
against dust and swarf by wearing approved safety goggles or a face shield. These are some of the
more common hazards and preventions, however, always find out what hazards are associated with
the machine/work process and wear the most suitable protective equipment available.
Do not breathe contaminated air. If the work creates dust or fumes connect the machine
(if possible) to an extraction system either locally or remotely. Working outdoors can also help
if possible.
Move the machine as instructed. If the machine is hand held, do not carry it by the power supply
cable. If the product is heavy, employ a second or third person to help move it safely or use a
mechanical device. Always refer to the instructions for the correct method.
Do not overreach. Extending your body too far can result in a loss of balance and you falling.
This could be from a height or onto a machine and will result in injury.
Maintain your tools correctly. A well maintained tool will do the job safely. Replace any damaged
or missing parts immediately with original parts from the manufacturer. As applicable keep blades
sharp, moving parts clean, oiled or greased, handles clean and emergency devices working.
- 6 -
10. MAINTENANCE
10.1 GEARBOX MAINTENANCE – FIG. 14
Note: Remove the plug from the socket before
carrying out adjustment, servicing or maintenance.
– Before each use remove the gearbox access
cover
(4) to ensure there is sufficient grease.
– Using pin spanner
(9) remove the access cover
(4) anti-clockwise.
– If required top-up the gearbox (20 grams max.)
using a general purpose lithium based grease.
– Lubricating the SDS MAX drill bit before
inserting into the SDS MAX chuck is advisable.
Warning! Assembly must be completed prior to
operating the machine.
The hammer drill does not require any special maintenance. Regularly clean/vacuum the
ventilation slots. Use only a mild cleaner and a damp cloth to clean the tool.
10.2 OPTIONAL ACCESSORIES
For a full range of optional accessories, please refer to your local Draper Stockist.
- 15 -
FIG.14
(9)
(4)

4. INTRODUCTION
4.1 SCOPE
For impact drilling/chiselling into brick, concrete and stone.
This product is intended for trade use and has the quality and features to meet and exceed the
expectations of the most demanding user. Any application other than that it was intended for, is
considered misuse.
4.2 SPECIFICATION
Stock no. ................................................................................................................................ 56407
Part no. .............................................................................................................. SDSMAXHD1600E
Rated voltage ................................................................................................................ 230V~50Hz
Rated input ............................................................................................................................ 1600W
Core drill capacity..................................................................................................................... 90mm
Note: This machine has a clutch so is suitable for occasional core drilling. It is not a dedicated
core drilling machine and must not be used as such.
Drilling capacity:
Masonry ......................................................................................................................... 40mm
Note: This figure is derived using a defined mix of concrete and as such, your material may be
harder or softer than the material, so a degree of leeway should be applied to this figure. A window
lintel for example will be much harder than the test concrete and this machine will not be able to
reach the same level of performance when compared to a softer mix of concrete.
Impact force...........................................................................................................................9 Joules
Revolutions per minute (no load) ....................................................................................... 560r/min
Impact rate ...................................................................................................................... 3530b/min
Chuck type ....................................................................................................................... SDS MAX
Sound pressure level* .............................................................................................. 93.9dB +/- 3dB
Sound power level** ............................................................................................... 104.9dB +/- 3dB
Vibration level:
hammer drilling into concrete ................................................................13.550m/s² +/- 1.5m/s2
chiselling................................................................................................ 12.299m/s² +/- 1.5m/s2
Weight (drill only)......................................................................................................................... 7kg
4.3 HANDLING & STORAGE
– Care must be taken when handling this product.
● Dropping this power tool could have an effect on its accuracy and could also result in
personal injury. This product is not a toy and must be respected.
– Environmental conditions can have a detrimental effect on this product if neglected.
● Exposure to damp air can gradually corrode components.
● If the product is unprotected from dust and debris, components will become clogged.
● If not cleaned and maintained correctly or regularly, the machine will not perform at its best.
* Continuous A-Weighted sound pressure level at the workstation in accordance to and declared
according to EN60745.
** The typical A-Weighted noise level determined according to EN60745.
- 5 -
11. TROUBLESHOOTING
11.1 TROUBLESHOOTING GUIDE
Note: Remove the plug from the socket before carrying out adjustment, servicing or maintenance.
- 16 -
Problem Possible Cause Remedy
Motor does not start. 1. Fuse.
3. Unsure.
1. Replace/reset 13 amp time
delay fuse or circuit breaker.
2. Have carbon brushes
replaced in motor.
3. Return to an authorised
service agent for diagnosis.
2. Brushes worn.

- 17 -
3. WARRANTY
- 4 -
3.1 WARRANTY
Draper tools have been carefully tested and inspected before shipment and are guaranteed to be
free from defective materials and workmanship.
Should the tool develop a fault, please return the complete tool to your nearest distributor or contact:
Draper Tools Limited, Chandler’s Ford, Eastleigh, Hampshire, SO53 1YF. England.
Telephone Sales Desk: [phone] or:
Product Helpline [phone].
A proof of purchase must be provided.
If upon inspection it is found that the fault occurring is due to defective materials or workmanship,
repairs will be carried out free of charge. This warranty period covering labour is 12 months from
the date of purchase except where tools are hired out when the warranty period is 90 days from
the date of purchase. The warranty is extended to 24 months from the date of purchase for parts
only. This warranty does not apply to any consumable parts, any type of battery or normal wear
and tear, nor does it cover any damage caused by misuse, careless or unsafe handling,
alterations, accidents, or repairs attempted or made by any personnel other than the authorised
Draper warranty repair agent.
Draper Tools Limited takes pride in the quality of its products and the services offered to our
valued customers. As a result we offer a free, 3 year extended warranty for this product.
REGISTER WITHIN 30 DAYS TO CLAIM YOUR
*To register your warranty, visit: drapertools.com/warranty-registration
or call our Customer Helpline on: [phone]
By registering your product you’ll automatically become a Draper Club Member where you will
have the option to receive news of our new products, offers, deals, competitions and more!
If you are unable to register online, please call our Customer Helpline on the number shown above.
Full registration must be completed within 30 days from receipt of purchase. The 3 year extended
warranty only applies to permanent UK residents, to the original product purchased from an
authorised Draper Tools stockist for use in their appropriate profession/trade. This warranty is not
valid to purchasers reselling or hiring the product. This warranty is not transferable and is only
available to the original product purchaser who has completed their registration and is a Draper
Club Member. The 3 year extended warranty period starts from the date of purchase and is not
extended following an inspection, repair or replacement.
Note: If the tool is found not to be within the terms of warranty, repairs and carriage charges will
be quoted and made accordingly.
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms
are not authorised.
Your Draper warranty is not effective unless you can produce upon request a dated receipt or
invoice to verify your proof of purchase within the warranty period.
Please note that this warranty is an additional benefit and does not affect your statutory rights.
Draper Tools Limited.
For full terms and conditions visit: drapertools.com/corporate-policies
FREE
12. DISPOSAL
12.1 DISPOSAL
– At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is
disposed of according to national regulations.
– Contact your local authority for details of collection schemes in your area.
In all circumstances:
● Do not dispose of power tools with domestic waste.
● Do not incinerate.
● Do not dispose of WEEE* as unsorted municipal waste.
* Waste Electrical & Electronic Equipment.

2. CONTENTS
1 TITLE PAGE
1.1 INTRODUCTION ............................................................................................................ 2
1.2 REVISION HISTORY ...................................................................................................... 2
1.3 UNDERSTANDING THIS MANUAL ...............................................................................2
1.4 COPYRIGHT NOTICE.....................................................................................................2
2 CONTENTS
2.1 CONTENTS.....................................................................................................................3
3 GUARANTEE
3.1 GUARANTEE .................................................................................................................. 4
4 INTRODUCTION
4.1 SCOPE ........................................................................................................................... 5
4.2 SPECIFICATION .............................................................................................................5
4.3 HANDLING & STORAGE................................................................................................ 5
5 HEALTH & SAFETY INFORMATION
5.1 GENERAL SAFETY INSTRUCTIONS ............................................................................6
5.2 SPECIFIC SAFETY INSTRUCTIONS FOR HAMMER DRILLS ..................................... 7
5.3 ADDITIONAL SAFETY INSTRUCTIONS FOR HAMMER DRILLS................................. 7
5.4 RESIDUAL RISK ............................................................................................................. 8
5.5 CONNECTION TO THE POWER SUPPLY..................................................................... 8
6 TECHNICAL DESCRIPTION
6.1 IDENTIFICATION ............................................................................................................9
7 UNPACKING & CHECKING
7.1 PACKAGING .................................................................................................................10
7.2 WHAT’S IN THE BOX.................................................................................................... 10
8 PREPARING THE DRILL
8.1 AUXILIARY HANDLE .................................................................................................... 11
9 BASIC HAMMER DRILL OPERATIONS
9.1 FUNCTION SELECTORS ............................................................................................. 12
9.2 PNEUMATIC HAMMER DRILLING ............................................................................... 13
9.3 PNEUMATIC CHISELLING ...........................................................................................13
9.4 ROTATIONAL CHISEL SELECTION.............................................................................13
9.5 TRIGGER SWITCH....................................................................................................... 13
9.6 SDS MAX SYSTEM ......................................................................................................14
9.7 DUST AND SWARF ...................................................................................................... 14
9.8 DRILLING WOOD, PLASTIC AND METAL ................................................................... 14
10 MAINTENANCE
10.1 GEARBOX MAINTENANCE .........................................................................................15
10.2 OPTIONAL ACCESSORIES..........................................................................................15
11 TROUBLESHOOTING
11.1 TROUBLESHOOTING GUIDE...................................................................................... 16
12 DISPOSAL
12.1 DISPOSAL.....................................................................................................................17
13 EXPLANATION OF SYMBOLS
13.1 EXPLANATION OF SYMBOLS .....................................................................................18
14 DISPOSAL
14.1 DISPOSAL.....................................................................................................................18
DECLARATION OF CONFORMITY .............................................................................. ENCLOSED
- 3 -
- 18 -
13.1 EXPLANATION OF SYMBOLS
13. EXPLANATION OF SYMBOLS
WEEE –
Waste Electrical &
Electronic Equipment.
Do not dispose of Waste Electrical
& Electronic Equipment in with
domestic rubbish.
Class II construction
(Double insulated).
Read the instruction manual.
Wear face mask and safety
glasses.
Wear ear defenders.
Wear protective gloves.
Do not abandon into the
environment.
Keep out of the reach of children.
Warning!

1. TITLE PAGE
1.1 INTRODUCTION:
USER MANUAL FOR: 230V 7kg SDS MAX Rotary Hammer Drill
Stock No: 56407
Part No: SDSMAXHD1600E
As our user manuals are continually updated, users should make sure that they use
the very latest version.
Downloads are available from: http://drapertools.com/manuals
Draper Tools Limited
Hursley Road
Chandler’s Ford
Eastleigh
Hampshire
SO53 1YF
UK
Website: drapertools.com
Product Helpline: [phone]
General Fax: [phone]
1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT:
WARNING! – Information that draws attention to the risk of injury or death.
CAUTION! – Information that draws attention to the risk of damage to the product or
surroundings.
1.4 COPYRIGHT © NOTICE:
Copyright © Draper Tools Limited.
Permission is granted to reproduce this publication for personal and educational use
only. Commercial copying, redistribution, hiring or lending is prohibited.
No part of this publication may be stored in a retrieval system or transmitted in any
other form or means without written permission from Draper Tools Limited.
In all cases this copyright notice must remain intact.
1.2 REVISIONS:
Date first published August 2018.
- 19 -
NOTES

Draper Tools Limited, Hursley Road,
Chandler’s Ford, Eastleigh, Hampshire. SO53 1YF. U.K.
Helpline: [phone]
Sales Desk: [phone]
Internet: drapertools.com
E-mail: [email protected]
General Enquiries: [phone]
Service/Warranty Repair Agent:
For aftersales servicing or warranty repairs, please contact the
Draper Tools Helpline for details of an agent in your local area.
©Published by Draper Tools Limited.
No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, mechanical photocopying, recording or otherwise without prior permission in writing from Draper Tools Ltd.
CONTACTS
YOUR DRAPER STOCKIST
TAPR0621
These instructions accompanying the product are the original instructions. This document is part of the product, keep
it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions before
assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.

230V 7KG
SDS MAX ROTARY
HAMMER DRILL
56407