Section 1 - Assembling Vertical Standards
1.
Attach power winch assembly to one of the 3½" (89mm) O.D. upright tubes
and temporarily tighten near the center of the standard with hex wrench.
2.
Attach cable anchor collar onto the other 3½" (89mm) O.D. upright tube
and temporarily tighten near the center of the standard with hex wrench.
3.
Install one sliding adjustment collar on each upright tube. Make sure collar
is installed so guide pin is located on the narrow vertical channel.
4.
Attach endcaps to both ends of standards.
5.
Install vertical standards in floor sleeves (see VB_FloorSleeves_Inst for details).
6.
Locate the center of the winch assembly 47" (1.19M) up from the playing surface and tighten screws with hex wrench.
7.
Locate the center of the cable anchor collar 47" (1.19 M) up from the playing surface and tighten screws with hex wrench.
NOTE: It will be necessary to move winch and cable anchor collar when using CVS volleyball system for nets heights other than Mens
/
Womens Volleyball.
8.
For initial set up, you will start by setting at MENS height. Position the center of the sliding adjustment collar approximately 1" (25mm) above the desired net
height or 8' 0-
5
/
8
" (2.45M) above the playing surface. Make sure guide pin is in the narrow vertical channel and tighten hand knob to secure in place. Hand knob
should tighten so that it is fully inside wider vertical channel.
Section 2 - Attaching Net to Standards
1.
Unroll net on floor between standards.
2.
If not already in place, install ½" (13mm) fiberglass rods in
ends of net.
3.
String net between standards by sliding looped cable
over pulley on sliding adjustment collar.
4.
Unspool the 2" (51mm) nylon strap from power winch.
Hook one end of the top net cable in hook on belt.
Hook opposite end of top net cable to cable anchor collar
on the other standard.
NOTE: Make sure the cable is running cleanly through sheaves.
Section 4 - Tensioning the Net
1.
Tighten net by turning winch handle clock wise. Measure
distance from playing surface to the top of net at center.
Rules allow net to be ¾" (19mm) higher at court sidelines.
2.
Set net height to 7' 11
5
/
8
" (2.43m).
3.
Tie a loop in one end of the bottom net rope. Loop is usually at
end with cable anchor collar for convenience. Hook rope to
cable anchor collar (or power winch).
4.
Insert the remaining end of bottom net rope into rope tensioner
and clip it to the power winch (or cable anchor collar).
5.
Wrap 1" (25mm) wide net tension straps once
around standards and tighten using buckles.
NOTE: Winch incorporates a worm gear type
mechanism.
To loosen top cable, turn winch handle
counterclockwise.
5.
Remeasure at center to ensure proper net height.
The Combination Volleyball System is
now set for regulation MENS volleyball.
FLOOR PLATE (2)
(Ordered Seperately)
3 ¼” (8.89cm) ID
FLOOR SLEEVE
501006
(Ordered Seperately)
ENDCAP
ENDCAP
Combination Antenna
and Boundary Marker
CABLE
ANCHOR
COLLAR
SLIDING
ADJUSTMENT
COLLAR
POWER WINCH
with
Folding Handle
SLIDING
ADJUSTMENT
COLLAR
½" (1.27cm)
fiberglass dowel rod (2)
ROPE
TENSIONER
2" (5.08cm)
NYLON STRAP
Combination Antenna
and Boundary Marker
CENTER of COLLAR
NET TENSION
STRAPS
BOTTOM NET ROPE
TOP NET CABLE
MENS &
WOMENS
47” (119.4cm)
ABOVE
PLAYING
SURFACE
NET
HEIGHT
3’ 3 3/8”
(1 METER)
1’ 9”
(53.3cm)
NET
HEIGHT
3’ 3 3/8”
(1 METER)
MENS &
WOMENS
47” (119.4cm)
ABOVE
PLAYING
SURFACE
PLAYING
SURFACE
PLAYING
SURFACE
ADJUSTMENT COLLAR
CABLE ANCHOR COLLAR
POWER WINCH
ASSEMBLY
As A Set: C129.029 PN: C132.050
Figure 1
page 2 of 4
Combination Volleyball System
