DRESKAR FT001 User manual

USERMANUAL
Your satisfaction is our greatest motivation! Please let us know if you haveany question or
would like any further information:[email protected]
DRESKAR
Electric Skateboard
DRIFT THE STREETS WITH THE BEST
DRESKAR
Electric Skateboard
DRIFT THE STREETS WITH THE BEST

Please read and understand this entire manual before riding the electric
skateboard.
Do note that electric skateboard is not a toy. Please take time to learn
it and read this manual carefully. Particularly the safety instruction
pages.
We hope you will enjoy this product and have
lots of fun with it in the future.
HappyRiding!
DresKarTeam.
Thankyouforyourpurchaseof
ourelectricskateboard!

ElectricSkateboardFeatures
Top Speed 25MPH
900x2W Dual motors
20% uphill capability
Belt transmission system
7.5AH High
performance battery
17 Miles Range
Durableand beautiful
Maximum load-bearing up to 330lb
1

GENERALINFORMATION
ABOUTTHEFT001
This User Manual will guide you through the functions and usage of your DresKar Electric
Skateboard. Before operating this vehicle read all the instructions for safe assembly,
charging, and operation.
Please inspect the DresKar unit upon unpacking for any signs of physical damage or defects.
If you have questions or have misplaced the DresKar Manual, contact DresKar before you
attempt to use or return your DresKar board.
DresKar is a high-tech company consisted of outstanding manufacturing, professional
research, and top design on electric skateboard. We commit our full efforts to produce
the high-class and intellectualized electric skateboard. Our electric skateboard will bring
customer entertainment x-sport experience and convenient transportation.
The DresKar FT001 electric skateboard is created for electric skateboard enthusiasts.
It’ssimple to operate, easy to control, and looks incredibly cool!
2

SAFETYWARNING
RISK OF DEATH SERIOUS INJURY
WARNING: AVOID WATER!
WARNING: PINCH POINTS!
Whenever you ride an electric skateboard, you risk death or serious injury from the loss of
control, collision, and falls.
To ride safely, you must read and follow the instructions and warnings in the manual.
Always wear a helmet when riding. Avoid water, wet surfaces, slippery/uneven surfaces,
steep hills, traffic, cracks, tracks, gravel, rocks, or any obstacles that could cause a loss of
traction and cause a fall.
Avoid night riding, areas with poor visibility, and small spaces.
Your board is not completely waterproof. You can easily go through the puddles but don't
soak the board the water. Water damage is not covered under the warranty
Keep fingers, hair, and clothing away from belts, motors, wheels, and all moving parts.
WARNING: RISK OF ELECTRIC SHOCK!
Do not open or tamper with electronics housing, which also voids the warranty.
3

E-SkateboardPartsDiagram
Tail Motor
Belt
Power button
Charging port
Controller Housing
Front Truck
Kingpin
Battery Housing
Power wheel
Waterproof
sand paper
Board Deck
Front wheel
Nose
4

E-SkateboardSpecifications
Size 1000*240MM
Capacity 7500mAh
KV value 270KV
Power 900W*2
Endurance 28KM
Material 5 Layers Maple +
2 Layers bamboo
Deck
Battery
Motor
Type N5055
Charging voltage
Type 18650
42V
10KM/H
25KM/H
40KM/H
2.4GHZ
14M
150mAh
Android
1000*255*145MM
1055*325*200MM
Speed
Remote
control
Package
Weight
Low speed
Frequency
Remote control
distance
Battery capacity
Charging Cable
Skateboard size
Carton size
N.W. 8.25KG
G.W. 10.4KG
Medium speed
High speed
PUMaterial
90*52MMSize
Wheel
5

RemoteControlDiagram
Reverse button
Power button
100% of the battery left
50% of the battery left
Signal indicator
10% of the battery left
The battery indicator of remote
Pair button
Charging port
Speed
mode toggle High
Middle
Low
Speed
Control Throttle Accelerate
Brake
Remote control indicator: Red light, no electricity, please charge
6

UsageandInstructions
The first step,the BOARD and REMOTE must be paired.Before riding,to ensure the BOARD
and REMOTE are turn off.
Remote
Connection
The pairing status icon
will remain steady while
connected.
7

Speed
Control Throttle
Brake
Accelerate
Connecting
1. Turn on the board.
2. Press the board power button for 5seconds.lt will flash.
3. Turn on the remote, then press the pair button. the signal indicator will flash and the power button light will
flash with the same frequency. Then means the paired successfully.
4. Push the joystick, forward to test the accelerate, and backward to test the brake. After testing all functions
work normally you can start your riding.
Acceleration/DecelerationButtons
The speed at which the skateboard accelerates/decel-
erates depends on how far down you push the Throttle.
Please start with the low speed mode to be familiar with
the accelerate and brake of the skateboard.
8

Note: Before riding, familiarize yourself with how to safely perform manual braking.
Push the throttle forward to accelerate.
Move the throttle wheel in small increments.
Keep a wide stance on the board.
Keep a low center of gravity.
Lean forward when accelerating.
Push the Throttle down to brake or
Decelerate.
Move the throttle wheel in small increments.
Keep a wide stance on the board.
Keep a low center of gravity.
Lean backward when accelerating.
9

Shutdown
CruiseControl
WARNING: WARNING:
When stop riding by brake operate.
Get down front foot at first, then get down your back foot.
Cruise Control will be deactivated if the skate-
board or remote loses power, or if the connec-
tion between skateboard and remote is lost.
Confirm the front direction of the skate-
board. The feet stand on the widest
front and back
Skateboard. Push and hold the Throttle
to activate the Cruise Control.
Before using this feature, be sure
you understand how to turn it on
and off.
10

TURNONLEDLIGHT
The light strips on both sides of the bottom of the Electric skateboard can change with
the driving forward and backward during the driving process, which will make driving
more cool and attract people's attention at night.
Turn on led light: Long press the Reverse button for 3-5seconds to turn on the light, the
same for turning off the light.
11

CHARGETHEREMOTE/BOARD
Remote charge time 30 minutes.
Indicator will turn from red to green
when fully charged.
USB
30mins
3hrs
1. Plug the charger into the mains socket (Charger Power:
110V-240V, 12V 4.5A). The light on the charger lights up
green.
2. Plug the other end of the charger into the device. The
indicator on the charger will turn red.
When the indicator turns from red to green, the charging is
complete, disconnect the charger from the device and
electrical outlets. Do not overcharge the device, as it may
affect battery life.
WARNING: Never leave board unattended while charging.
12

13
HowtoadjustDriveBelttightness?
1. Loosen the belt cover screws
and remove the motor cover.
2. Loosen the motor screws
until the motor can move
3. Tighten the screw of the pull
block, tighten the belt tightly,
loosen the screw loose
4. After adjusting the belt tightness,
tighten the motor screws
5. Attach the belt cover

SafeRidingTechniques
When operating, accelerating, decelerating, or braking, please keep your weight in line with the skate-
board direction in which you are going and in accordance with the functions you are performing in order
to increase your stability and avoid possible product damage.
● If braking or decelerating forward, you should lean and/or shift weight slightly backward.
● If starting or accelerating forward, you should lean and/or shift weight slightly forward.
● When atop the board, stand with feet apart so that your weight is more evenly distributed over the board.
This will improve your stability.
● Wearing appropriate clothing and safety gear including knee pads, elbow pads, wrist braces, and helmets.
● Wear flat shoes to maintain flexibility and stability.
● Ensure the vehicle speed is safe for yourself and others, and be ready to stop at any time.
+ Never perform stunts or turn abruptly without checking your surroundings.
+ Never carry one or more passengers on the skateboard with you.
+ Never carry heavy items while riding.
+ Never ride in the rain, dark, or dimly lit areas.
+ Never operate your skateboard near flammable vapor, liquids, dust, or other fire hazards.
WARNING:
14

BatterySafetyUsageWarnings
When Using the Battery
(1) Misusing the battery may cause the battery to get hot, rupture, or ignite and cause
serious injury. Be sure to follow the safety rules listed below:
● Do not place the battery in fire or direct contact with heat.
● Do not pierce the battery with sharp objects, strike the battery, step on the bat
tery, or otherwise subject it to strong impacts or shocks.
● Do not expose the battery to water or any liquids, or allow the battery to get wet.
(2) Do not disassemble or modify the battery. The battery contains safety and protection
devices that, if damaged, may cause the battery to generate heat, rupture, or ignite.
(3) Do not place the battery on or near fires, stoves, or other high-temperature locations.
Do not place the battery in direct sunlight, or use or store the battery inside cars in hot
or cold weather. Doing so may cause the battery to generate heat, rupture, or ignite.
Using the battery in this manner may also result in a loss of performance and a short
ened life expectancy.
15

ROUTINEMAINTENANCE
● Regularly inspecting your board for damage and checking that it is run
ning properly.
● Before riding make sure all screws are tight.
● Do not clean the board with harsh abrasives or chemicals; using a
semi-damp cloth to wipe off dust and dirt from belts, bearings and
wheels.
● Turn off the board and remote controller when not in use.
● Keep your board battery fully charged when not in use.
● Recharge the battery every 3 month.
● Do not leave the board charging unattended
● Disconnect the battery from charger once it is fully charged.
● Do not modify the electrical controls or wiring.
16

● Regularly inspecting your board for damage and checking that it is run
ning properly.
● Before riding make sure all screws are tight.
● Do not clean the board with harsh abrasives or chemicals; using a
semi-damp cloth to wipe off dust and dirt from belts, bearings and
wheels.
● Turn off the board and remote controller when not in use.
● Keep your board battery fully charged when not in use.
● Recharge the battery every 3 month.
● Do not leave the board charging unattended
● Disconnect the battery from charger once it is fully charged.
● Do not modify the electrical controls or wiring.
Howoftenshouldyoureplacedrivebelts?
Generally, whether to replace the belt depends on the frequency of your use and the
degree of wear and tear of the belt. It is suggested that you should check the belt once a
week. If the belt wears severely, the belt needs to be replaced.
Generally, the drive belt needs to be replaced after 6 months of use.
HowtocleanthebearingsandWheels
It is important to clean your electric skateboard after each ride. Clean the electric skate-
board with a slightly damp cloth and prevent any water or dirt from entering the electronic
components. After this, wipe the board with a dry cloth.
To maintain your bearings. You can do this with the special maintenance oil "Bearing
Cleaner & Lube". This oil is specially developed for the maintenance of the bearings and
ensures that your bearings last a long time.
17

WARRANTY
WarrantyCard
LIMITED WARRANTY:
Information I:
Repair Date
SN
Model
Fault Phenomenon
Analysis of Causes
Signature of Analyst
●We offer 12 months warranty on all parts of the electric skateboard from the date when
you receive the board except for the battery.
● We offer 6 months warranty on the battery.
● This warranty excludes damage resulting from abuse, accident, modifications, unau-
thorized repairs, neglect, abuse, water damage, or other causes that are not defects in
materials and workmanship.
● This warranty excludes normal depletion of consumable parts(grip tape, wheels &
bearings) unless due to a defect in materials or workmanship.
18