DT Research LT330 Assembly instructions

Rugged Convertible Laptop
Federal Communication Commission Interference
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician forhelp.
FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate
this equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in
conjunction with any other antenna or transmitter.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe [B] est conforme à la norme NMB-003 du
Canada.
LT330
INTRODUCTION
Thank you for acquiring DT Research’s LT330 Rugged Laptop. Featuring a slim yet
robust enclosure, the Rugged Laptop with a 13.3” convertible display and an LED-
backlit keyboard is powered by the Intel® processor, offering optimal combinations
of performance and power savings. The LT330 Rugged Laptop is available with
Microsoft® Windows® operating system. The software operating system features
web browser, client/ server computing software, media player, accessories, and
applications support.
PACKAGE CONTENTS
• One LT330 with one Battery Pack
• AC-DC Power Adapter with Power Cord
• Basic Operation Guide
DT Research, Inc.
2000 Concourse Drive, San Jose, CA 95131
Copyright© 2020, DTResearch, Inc. AllRightsReserved. BOG083120 LT330 ENG

2
3
PRECAUTIONS
• Always exercise care when operating and handling the LT330.
• Do NOT apply excessive pressure to the display screen.
• We recommend using the Digital Pen (optional) to keep the screen clean.
• Avoid prolonged exposure of the display panel to any strong heat source.
Wherever possible, the LT330 should face away from direct light to reduce glare.
• If the AC-DC power adapter is used to recharge or power the laptop, do NOT
use any AC-DC adapter other than the one provided or acquired from the
manufacturer or its partners.
• In the unlikely event that smoke, abnormal noise, or strange odor is present,
immediately power off the LT330 and disconnect all power sources. Report the
problem to your device provider immediately.
• Never attempt to disassemble the LT330, as this will void the warranty.
Input/ Output Ports
Button Functions
BASIC FEATURES
The LT330 rugged laptop integrates a high-brightness touchscreen, USB ports, and
embedded networking elements such as wireless LAN and Bluetooth or optional 4G
LTE/ AWS.
A LT330 typically integrates an 802.11ac wireless LAN (WLAN) adapter that may
connect to other wireless devices or access points. If your LT330 does not come with
such a network adapter, please consult your device provider to establish the desired
network connectivity.
NOTE:
To obtain protection consistent with any IP rating for the device, the I/O (audio,
power, USB, card reader, etc.) port doors must be closed. If the IP protection is
compromised by mishandling or misuse, such as by leaving port doors open or
improperly closed, any resulting product damage will not be covered under any
DT Research warranty.
BUTTON ACTION BUTTON ACTION
1Power Button 588 Standard, Full-size
Keyboard with Backlight
2Programmable Buttons 6Multi-touch Pad
3Brightness Control Buttons 7Service Door Switch
4Programmable Button or
NVIS/ Normal Mode Toggle
8Battery Latchs *Push the switch up
to unlock the latch, then slide the latch
left to remove the battery.
A Ethernet Port (RJ45)
USB Type-C Port
B (for data transmitting, video-out, and also
for charging)
C USB 3.0 Ports
D DC-in Jack
E Kensington Security Slot
F COM Port
G HDMI Output Port
H Audio Jack
I Smart Card/CAC Reader
J Smart Card/CACReader
Cap Latch

4
5
OPERATION
Powering ON and OFF
To activate the LT330, push and quickly release the Power Button. The display will come
on in a few seconds. To put the LT330 in Standby mode, push and quickly release the
Power Button. To turn the LT330 off for extended storage, power off safely using any
software function that “shuts down computer” provided in the software operating
system.
Start Up
If the power up (from Standby mode or otherwise) is successful, the appropriate
interface will be displayed after a launch sequence of several seconds. The wireless
LAN connection may take 10-15 seconds to be established.
Configuring the Rugged Laptop
The LT330 may be configured using the utilities and methods dictated by the
software operating system. The LT330 should be configurable for various properties
such as user profiles, network features, and several system elements.
Covert the LT330
1. Unlock the latch to release the keyboard from the screen
2. Gently pull out the keyboard
3. Rotate the keyboard against the back of the screen
NOTE:
Avoid using the Power Button (“hold 4+ seconds” feature) to turn off the laptop—
this form of hardware shutdown is intended to be a means of recovery from
lockups, and not as normal operation.
NOTE:
When the battery pack is charging, the blue Battery LED should blink slowly.
If plugging in the AC-DC adapter does not trigger this blinking activity and the
LED stays dark, the battery pack(s) may have been drained substantially. Try
unplugging/ replugging the AC-DC adapter to the LT330 a few times to activate
the charging process.
NOTE:
The battery pack shipped with your laptop may be low in power—please use the
AC-DC adapter with the LT330 when setting up for the first time to fully charge
the battery pack, or use the optional battery charger kit.
NOTE:
To conserve power, use (push and quick release) the Power Button to put the
laptop in “Standby” mode while not in use. Pushing briefly on the same button
will wake up the system within seconds.

6
7
NVIS Mode and Screen Brightness Control (optional)
• When power button is pressed to power on the unit, power LED will flash orange
once to indicate the unit is booting. Unit will boot into NVIS mode with zero nit
brightness by default and display will be dark. You can press the “Brightness Up”
and “Brightness Down” buttons to set NVIS mode display to desired brightness
(up to 20 nits).
• To toggle between NVIS and high-brightness display mode, press the “NVIS/
Normal Mode Toggle” button. When changed from NVIS mode tohigh-brightness
mode, display brightness percentage will be same as the brightness level set in
NVIS mode before toggling.
• Use brightness control buttons to set desired brightness level. When changed
from normal display mode to NVIS mode, display brightness will be set to 0 nit
(display is dark) and you need to use brightness control buttons to change display
to desired brightness.
• Brightness up, Brightness down, NVIS/Normal toggle, Windows Key and Control
Center functions are fixed and not user programmable.
• Two programmable buttons on left side can be programmed through Button
Manager.
Wireless Networking
Wireless LAN
The LT330 is often delivered with an embedded (user-inaccessible) 802.11ac WLAN
adapter equipped with a hidden custom antenna.
• Through the support of typical WLAN adapters, the LT330 should be able to
detect all 802.11 access points in the vicinity to select the access point of choice
for connection.
• The SSID and WEP/WPA/WPA2 (if enabled) parameters on the LT330 and the
access points have to match. The SSID is case-sensitive and it is recommended to
enable WEP/WPA/WPA2 encryption (or advanced alternatives) for secureaccess.
• When WEP/WPA/WPA2 is enabled, you may need to consult your network
administrator or your networking equipment literature to properly configure
associated settings such as Authentication mode, etc.
• Refer to the access point operating manuals for setting up the 802.11access
points.
Bluetooth
The Bluetooth configuration application is enabled from the System Tray or from the
Windows Mobility Center. Follow the instructions and options provided within the
application to configure and invoke Bluetooth connectivity with the corresponding
peripherals.
USING THE RUGGED LAPTOP
Peripherals Support
Through its USB 3.0 ports, the LT330 supports a wide range of USB-based
peripherals. These peripherals are applicable for software installation, applications
storage, data storage, and system software recovery and updates.
For More Support
Users can download the Laptop Modules Basic Operation Guides from the DT Research
website.
If the LT330 comes with a Mobile broadband module, please contact your product
and/or service provider for the SIM Card installation procedures.

6
7
RF Exposure Compliance
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment.
The device has been tested for use against the body with 0mm separation in
Specific Absorption Rate (SAR) testing.
User must follow the specific operating instructions for satisfying RF exposure
compliance. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
Supplier's Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Unique Identifier Trade Name:
Model No.:
LT330
Responsible Party
– U.S. Contact Information
DT Research, Inc.
2000 Concourse Drive, San Jose, C
A 95131
http://www.dtresearch.com
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the
following two conditions: (1) This device may not cause har
mful interference, and (2)
this device must accept any
interference received, including interference that may
cause
undesired operation.
FCC ID Label is in removable battery compartment, it could be easily found by
removing the battery cover.
RF Exposure Information(RED)
This device was tested for typical body-worn operations. To comply with RF
exposure requirements, a minimum separation distance of 0cm must be maintained
between the user’s body and the handset, including the antenna.
The band 5150-5350 MHz for this device are restricted to indoor use only within all
European Union countries.
Hereby, [DT Research, Inc.] declares that the radio equipment type [LT330] is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
http://www.dtresearch.com.
Maximum EIRP for EU
Bluetooth:2402MHz-2480MHz
14.4dBm
Bluetooth LE:2402MHz-2480MHz
2.42dBm
Wifi: 2412MHz-2472MHz/2422MHz-2462MHz 20dBm
Wifi: 5150MHz-5725MHz
22.9dBm
Wifi: 5725MHz-5875MHz
13.9dBm