Dual XD1222 Operating instructions

AM/FM/CD Receiver with Auxiliary Input, USB Charging Port and
Detachable Face
M9&'''
Charge Port
>CHI6AA6I>DC$DLC:GHB6CJ6A

2
EgZeVgVi^dc
KEYS
HEX BOLT
MOUNTING SLEEVE
PLAIN WASHER
HEX NUT
MOUNTING STRAP
INE>86ABDJCI>C<B:I=D9
M9&'''>CHI6AA6I>DC
Please read entire manual before installation.
7Z[dgZNdjHiVgi
s$ISCONNECTNEGATIVEBATTERYTERMINAL#ONSULTAQUALIFIEDTECHNICIANFORINSTRUCTIONS
s!VOIDINSTALLINGTHEUNITWHEREITWOULDBESUBJECTTOHIGHTEMPERATURESSUCHASFROM
DIRECTSUNLIGHTORWHEREITWOULDBESUBJECTTODUSTDIRTOREXCESSIVEVIBRATION
<Zii^c\HiVgiZY
s2EMOVETRANSITSCREWSLOCATEDONTOPOFTHEUNIT
s)NSERTTHESUPPLIEDKEYSINTOTHESLOTSASSHOWNANDSLIDETHEUNITOUTOFTHEMOUNTING
sleeve.
s)NSTALLMOUNTINGSLEEVEINTOOPENINGBENDINGTABSTOSECURE
s#ONNECTWIRINGHARNESSANDANTENNA#ONSULTAQUALIFIEDTECHNICIANIFYOUAREUNSURE
s#ERTAINVEHICLESMAYREQUIREANINSTALLATIONKITANDORWIRINGHARNESSADAPTERSOLD
separately).
s4ESTFORCORRECTOPERATIONANDSLIDEINTO
mounting sleeve to secure.
s3NAPTRIMRINGINTOPLACE

3
Rear Preamp Output
Connect to amplifier RCA input
Antenna Connector
RCA Cable
(sold separately)
AMP
BLUE
BLACK
RED
YELLOW
Remote Turn-On
Connect to amplifier or power
antenna. Insulate wire if not used.
Ground
Connect to vehicle
chassis ground.
Accessory
Connect to ignition
circuit or switched 12 volt source.
Memory
Connect to battery
circuit or constant 12 volt source.
Right Front
Gray/Black (-)
Gray (+)
Left Front
White/Black (-)
White (+)
Right Rear
Violet/Black (-)
Violet (+)
Left Rear
Green/Black (-)
Green (+)
5 AMP
AGC Fuse
L^g^c\9^V\gVb
FUSE
When replacing the fuse,
MAKESURENEWFUSEISTHE
correct type and amperage.
Using an incorrect fuse
could damage the radio.
4HE8$USESONEAMP
AGC fuse located in-line.
* 8Vji^dc$ONOTATTACHANYSPEAKERLEADSTOGROUNDASSEVEREDAMAGEWILLOCCUR
M9&'''>CHI6AA6I>DC

4
8dcigdaAdXVi^dch
Release
Mode
Power
Rotary Encoder
Preset 4/Play/Pause
0RESET2EPEAT
0RESET
Preset 2/Random
Preset 3/Intro
Preset 6
1
2
3
4
5
6
7
8
9
10
4UNE4RACK$OWN
%JECT
4UNE4RACK5P
EQ/Stereo/Mono
Auxiliary Input
Audio/Loudness
USB Charge
AS/PS
Band
Display
11
12
13
14
15
16
17
18
19
17 16
12 3 8
19 18
M9&'''DE:G6I>DC
4HE8$HASANEASYTOUSEINTERFACETHATPROVIDESAREWARDINGEXPERIENCEAS
WELLASSUPPORTFORYOURFAVORITETUNES!UDIO#$2AND#$27DISCPLAYBACKENSURES
compatibility with your music collection, and the RCA preamp output provides the right
connections to expand your system. From its front panel auxiliary input for connecting your
MP3 player, to the detachable face for security assurance, this head unit has you covered.
4 65 119 12 137 10
141520
20


<ZcZgVaDeZgVi^dc
Press G:A:6H: and pull away from the left side to remove.
4OREINSTALLINSERTRIGHTSIDEOFFACEPLATEFIRSTTHENPUSHLEFT
side to secure.
2EMOVETRIMRINGANDINSTALLSUPPLIEDXv0HILLIPSHEAD
screw through left side of mounting frame into faceplate.
Press ELG to turn the unit on. Inserting a CD will turn the
unit on automatically. Press ELG to turn the unit off.
Press BD9: to select between AM/FM, CD or auxiliary input.
Modes of operation are indicated in the display.
Press and hold ADJ9 for 2 seconds to activate and deactivate
the loud feature. Activating this feature will enhance the
BASSANDTREBLEFREQUENCIESWHENLISTENINGTOMUSICATLOW
volumes.
)NSERTAMMCONNECTORINTHEFRONTPANEL!58PORT
#ONNECTTHEOTHERENDOFTHEMMCONNECTORTOTHE
headphone output of an audio device, MP3 player, etc. Press
BD9:TOSELECT!58MODE
!DJUSTVOLUMEUSINGTHEgdiVgnZcXdYZg
Press 9>HETODISPLAYTHECLOCK4HERADIOFREQUENCYTUNER
MODEAND#$TRACKELAPSEDTIME#$PLAYERMODEWILLBE
shown by default.
Press 9>HETODISPLAYTHECLOCKTHENRELEASE0RESSAND
hold 9>HEFORSECONDSTHECLOCKWILLBEGINTOFLASH0RESS
IG68@
nn
TOADJUSTTHEHOURSANDIG68@
ll
TOADJUST
THEMINUTES#LOCKSETTINGSWILLBESAVEDAFTERSECONDS
4HECLOCKWILLDISPLAYHOUR!-0-TIMEIN53!FREQUENCY
SPACINGMODE0-)N%UROPEANFREQUENCYSPACING
MODETHECLOCKWILLDISPLAYHOURTIME
Press and hold for more than 2 seconds to G:H:I the unit
UPONINITIALINSTALLATION4HEG:H:I button is located behind
the faceplate.
;VXZeaViZGZbdkVa
HZb^"eZgbVcZci;VXZeaViZ
>chiVaaVi^dc
EdlZgDc$D[[
BdYZ
AdjY
6jm^a^Vgn>ceji
KdajbZ
9^heaVn
HZii]Z8adX`
&'$')"]djg8adX`
GZhZi
M9&'''DE:G6I>DC

6
<ZcZgVaDeZgVi^dc
Insert the USB connector of a battery powered USB device
into the USB charging port on the front panel, which
PROVIDESVOLTS$#ANDAMPS4HE53"DEVICEWILL
immediately begin charging.
.OTE4HE53"CHARGINGPORTMAYNOTBECOMPATIBLEWITH
EVERYDEVICEDUETODIFFERENCESINPOWERREQUIREMENTS
.OTE4HIS53"PORTPROVIDESPOWERONLYANDWILLNOT
PLAYBACKMUSICFROMA53"DEVICE
Press 6J9>DTOSELECTBETWEEN6OLUMEDEFAULT"ASS
4REBLE"ALANCE&ADER
Press 6J9>D until BA appears
Rotate the gdiVgnZcXdYZgLEFTRIGHTTOADJUST
MINIMUMMAXIMUM
Press 6J9>DUNTIL42APPEARS
Rotate the gdiVgnZcXdYZgLEFTRIGHTTOADJUST
MINIMUMMAXIMUM
Press 6J9>D until B appears
Rotate the gdiVgnZcXdYZgLEFTRIGHTTOADJUST
","2"REPRESENTSEQUALBALANCE
Press 6J9>D until F appears
Rotate the gdiVgnZcXdYZgLEFTRIGHTTOADJUST
&&&2&REPRESENTSEQUALBALANCE
Press :F to select between CLS, POP, ROC and OFF
DEFAULTEQUALIZATIONCURVES!NYADJUSTMENTTOTHE"ASSOR
4REBLESETTINGSAUTOMATICALLYCANCELSTHECURRENT%1CURVE
JH78]Vg\^c\Edgi
HZaZXi6jY^d

7Vhh
IgZWaZ
7VaVcXZ
;VYZg
EgZhZi:F8jgkZh
BASSVOLUME TREBLE BALANCE FADER
M9&'''DE:G6I>DC


IjcZgDeZgVi^dc
Press IJC:
nn
or IJC:
ll
MOMENTARILYTOSEEKTHE
next strong station.
Press IJC:
nn
or IJC:
ll
for more than 2 seconds,
THENRELEASEh-!.5vWILLMOMENTARILYAPPEARINTHEDISPLAY
Press IJC:
nn
or IJC:
ll
momentarily to move radio
FREQUENCYUPORDOWNONESTEPATATIME0RESSANDHOLDTO
ADVANCEQUICKLY)FTUNINGISNOTADJUSTEDFORSECONDSTHE
UNITWILLRETURNTOSEEKTUNINGMODEDEFAULTh!54/vWILL
momentarily appear in the display.
Press HI$BD for more than 2 seconds during FM tuner
OPERATIONTOSELECTMONOORSTEREODEFAULTRECEPTIONOFTHE
broadcast signal.
Press 76C9TOSELECTBETWEEN&-&-&-AND!-!-
bands.
Press and hold 76C9 then press IJC:
nn
to select
%UROPEANFREQUENCYSPACING0RESSANDHOLD76C9 then
press IJC:
ll
TOSELECT53!FREQUENCYSPACINGDEFAULT
!NYTIMEFREQUENCYSPACINGISCHANGEDALLSTATIONPRESETS
are erased.
5PTO&-STATIONSAND!-STATIONSCANBESTORED
4OSTOREASTATIONSELECTTHEDESIREDBANDANDSTATION
Press and hold the desired preset button for more than 2
seconds. When stored, the preset number will appear in the
DISPLAY4HESTATIONCANBERECALLEDANYTIMEBYPRESSINGTHE
corresponding preset button.
Press 6H$EH for more than 2 seconds to automatically store
the six strongest stations in the current band.
Press 6H$EHMOMENTARILYTOSCANPRESETSONTHECURRENT
BANDPAUSINGFORSECONDSATEACH0RESS6H$EH again to
cancel.
HZZ`Ijc^c\
BVcjVaIjc^c\
;BHiZgZd$Bdcd
7VcY
;gZfjZcXnHeVX^c\

Hidg^c\VcYGZXVaa^c\
HiVi^dcEgZhZih
6jidbVi^XVaanHidgZ
HiVi^dch
EgZhZiHXVc
M9&'''DE:G6I>DC


89EaVnZgDeZgVi^dc
7ITHTHELABELFACINGUPINSERTASTANDARDSIZE#$INTOTHE
#$SLOT4HE#$WILLAUTOMATICALLYBEGINPLAYBACK
Press the :?:8IBUTTONTOSTOPANDEJECTTHE#$
4HEUNITWILLCHANGETOTUNERMODE
Press IG68@
ll
TOSKIPTOTHEBEGINNINGOFTHENEXTTRACK
Press IG68@
nn
to return to the beginning of the current
TRACK0RESSINGIG68@
nn
AGAINSKIPSTOTHEBEGINNINGOF
THEPREVIOUSTRACK
Press and hold IG68@
ll
or IG68@
nn
to fast forward
ORREVERSEATRACK
Press
l
/ II TOTEMPORARILYSTOP#$PLAYBACK
Press
l
/ II AGAINTORESUMEPLAYBACK
Press >CITOPLAYTHEFIRSTSECONDSOFEACHTRACK
Press >CI to cancel.
Press GEITOCONTINUOUSLYREPEATSELECTEDTRACK
Press GEI to cancel.
Press G9BTOPLAYALLTRACKSINRANDOMORDER
Press G9B again to cancel.
Some CD-Rs and CD-RWs may be incompatible with this
unit, depending on media type and recording method.
.OTE#$2RECORDINGSESSIONSMUSTBECLOSEDFINALIZEDFOR
PLAYBACK
>chZgi89
:_ZXi89
IgVX`HZaZXi
;Vhi;dglVgYVcYGZkZghZ
EVjhZ
>cigd
GZeZVi
GVcYdb
89"G$89"GL
8dbeVi^W^a^in
M9&'''DE:G6I>DC

9
IgdjWaZh]ddi^c\
Problem Cause Action
Yellow wire not connected or incorrect voltage
Red wire not connected or incorrect voltage
#HECKCONNECTIONSFORPROPERVOLTAGE
^6$#
"LACKWIRENOTCONNECTED #HECKCONNECTIONTOGROUND
Fuse blown Replace fuse
3PEAKERWIRESNOTCONNECTED #HECKCONNECTIONSATSPEAKERS
/NEORMORESPEAKERWIRESTOUCHINGEACH
other or touching chassis ground
)NSULATEALLBARESPEAKERWIRESFROM
each other and chassis ground
Yellow or red wire touching chassis ground #HECKFORPINCHEDWIRE
3PEAKERWIRESTOUCHINGCHASSISGROUND #HECKFORPINCHEDWIRE
Incorrect fuse rating Use fuse with correct rating
5NITISNOTMOUNTEDCORRECTLYORBACKSTRAPIS
not secure
CD mechanism position out of alignment
CD transit screws still in place
#HECKMOUNTINGSLEEVEANDBACKSTRAP
support
0HYSICALDEFECTINMEDIA#$#$2OR#$ RW) #HECKMEDIAFORSCRATCHES
0RESS%*%#4FORSECONDSTORESET
CD mechanism position
Remove 2 transit screws located on top
of the unit.
Unit will not turn on
NOPOWER
Unit has power
BUTNOSOUND
Unit blows fuses
%XCESSIVESKIPPING
Unit will not accept
a disc
:ggdg8dYZh
Error Code Cause Action
%2APPEARSONDISPLAY Disc error 0RESSEJECTOR2%3%4
ER-2 appears on display Mechanism error 0RESSEJECTOR2%3%4
ER-3 appears on display Servo error or disc is in upside down 0RESSEJECTOR2%3%4
M9&'''DE:G6I>DC


A^b^iZYDcZNZVgLVggVcin
4HISWARRANTYGIVESYOUSPECIFICLEGALRIGHTS
You may also have other rights which vary from
state to state.
Dual Electronics Corp. warrants this product to
the original purchaser to be free from defects in
MATERIALANDWORKMANSHIPFORAPERIODOFONE
year from the date of the original purchase.
Dual Electronics Corp. agrees, at our option,
during the warranty period, to repair any defect
INMATERIALORWORKMANSHIPORTOFURNISHAN
EQUALNEWRENEWEDORCOMPARABLEPRODUCT
WHICHEVERISDEEMEDNECESSARYINEXCHANGE
WITHOUTCHARGESSUBJECTTOVERIFICATIONOFTHE
defect or malfunction and proof of the date of
PURCHASE3UBSEQUENTREPLACEMENTPRODUCTS
are warranted for the balance of the original
warranty period.
L]d^hXdkZgZY44HISWARRANTYISEXTENDEDTO
the original retail purchaser for products
purchased and used in the U.S.A.
L]Vi^hXdkZgZY44HISWARRANTYCOVERSALL
DEFECTSINMATERIALANDWORKMANSHIPINTHIS
PRODUCT4HEFOLLOWINGARENOTCOVERED
installation/removal costs, damage resulting
from accident, misuse, abuse, neglect, product
modification, improper installation, incorrect
LINEVOLTAGEUNAUTHORIZEDREPAIRORFAILURETO
follow instructions supplied with the product,
or damage occurring during return shipment of
the product.
L]ViidYd4
"EFOREYOUCALLFORSERVICECHECKTHE
troubleshooting guide in your owner’s
MANUAL!SLIGHTADJUSTMENTOFANYCUSTOM
controls may save you a service call.
)FYOUREQUIRESERVICEDURINGTHEWARRANTY
PERIODYOUMUSTCAREFULLYPACKTHEPRODUCT
PREFERABLYINTHEORIGINALPACKAGEANDSHIP
it by prepaid transportation with a copy of the
original receipt from the retailer to an
AUTHORIZEDSERVICECENTER
3. Please describe your problem in writing and
include your name, a return UPS shipping
ADDRESS0/"OXNOTACCEPTABLEANDA
daytime phone number with your shipment.
4. For more information and for the location of
THENEARESTAUTHORIZEDSERVICECENTERPLEASE
CONTACTUSBYONEOFTHEFOLLOWINGMETHODS
s#ALLUSTOLLFREEAT
s%MAILUSATCS DUALAVCOM
%XCLUSIONOF#ERTAIN$AMAGES4HISWARRANTY
is exclusive and in lieu of any and all other
warranties, expressed or implied, including
without limitation the implied warranties of
merchantability and fitness for a particular
purpose and any obligation, liability, right,
claim or remedy in contract or tort, whether
or not arising from the company’s negligence,
actual or imputed. No person or representative
ISAUTHORIZEDTOASSUMEFORTHECOMPANYANY
other liability in connection with the sale of
this product. In no event shall the company be
LIABLEFORINDIRECTINCIDENTALORCONSEQUENTIAL
damages.
M9&'''L6GG6CIN


M9&'''CDI:H

Specifications
&REQUENCYRESPONSE(ZK(Z
#HANNELSEPARATION K(ZD"
$!CONVERTER"IT
4UNINGRANGE-(Z-(Z
5SABLESENSITIVITYD"F
D"QUIETINGSENSITIVITYD"F
3TEREOSEPARATION K(ZD"
&REQUENCYRESPONSE(ZK(Z
4UNINGRANGEK(ZK(Z
5SABLESENSITIVITYU6
&REQUENCYRESPONSE(ZK(Z
/PERATINGVOLTAGE6$#NEGATIVEGROUND
3PEAKEROUTPUTIMPEDANCE^OHMS
&USEAMP!'#
$IMENSIONSXXXXMM
$ESIGNANDSPECIFICATIONSSUBJECTTOCHANGEWITHOUTNOTICE
CD Player
&-4UNER
!-4UNER
General
8:6"'%%+EdlZgHiVcYVgYHeZX^[^XVi^dch
REFERENCE6$#6(Z^K(Z
0OWER/UTPUT7ATTS2-3XCHANNELSATOHMSAND<4($.
3IGNALTONOISERATIOD"!REFERENCEWATTINTOOHMS
Dual Electronics Corp.
4OLL&REE
www.dualav.com
¥$UAL%LECTRONICS#ORP!LLRIGHTSRESERVED
.3!6

~E
o
U
Ln
·
I>
N~
CX)ro
M:::J
--b~
~
CX)
I
p-
0:::
Ww
~u
Oz
tn~
::>V)
u-
....JV)
~V)
::>~
cO:::
wO
:eLL
~w ....J~
....J....J
~~
w-
V»
<Co::::
wW
....JV)
c..
~w
:eo:::
~o
z~
0:::
V)
::>W
~:e w~
0:::
0
I-~
01-
z-
oZ
c::>
DO NOT RETUR THIS
U IT TO HE STORE
PLEASE CALL THE DUAL CUSTOMER
SERVICE LINE FOR ASSISTANCE
1-866-382-5476
www.dualav.com

0-'
Attaching The Front Panel: 0-'
1. Align and insert the right side of the front panel to the unit as shown below.
2. While keeping the right side in position, press the left side of the front panel towards the unit.
3. Press firmly until the front panel"clicks" into place.
Attaching The Front Panel: 0-'
1. Align and insert the right side of the front panel to the unit as shown below.
2. While keeping the right side in position, press the left side of the front panel towards the unit.
3. Press firmly until the front panel"clicks
tl
into place.

FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference. and
(2) this device must accept any interference received. including interference that may
cause undesired operation.
Warning: Changes
or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for aClass
Bdigital device. pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in aresidential
installation. This equipment generates. uses and can radiate radio frequency
energy and.
if not installed and used in accordance with the instructions. may cause
harmful interference
to radio communications. However. there is no guarantee that
interference
will not occur in aparticular installation. If this equipment does cause
harmful interference to radio
or television reception. which can be determined
by turning the equipment off and on. the user is encouraged to try to correct the
interference by one
or more of the following measures:
•Reorient
or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet
on acircuit different from that to which the
receiver is connected.
•Consult the dealer
or an experienced radiolTV technician for help.
In
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference. and
(2) this device must accept any interference received. including interference that may
cause undesired operation.
Warning: Changes
or modifications to this unit not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
Note: This equipment has been tested and found to comply with the
limits for aClass
Bdigital device. pursuant
to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in aresidential
installation. This equipment generates. uses and can radiate radio frequency
energy and.
if not installed and used in accordance with the instructions. may cause
harmful interference
to radio communications. However. there is no guarantee that
interference
will not occur in aparticular installation. If this equipment does cause
harmful interference to radio
or television reception. which can be determined
by turning the equipment off and on. the user is encouraged to try to correct the
interference by one
or more of the following measures:
•Reorient
or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet
on acircuit different from that to which the
receiver is connected.
•Consult the dealer
or an experienced radiolTV technician for help.
In