Duevi DV-TOUCH User manual

DVTOUCH 20.02-M:1.0-H:01V3-19-F:1.00
DV-TOUCH Touch Screen Keyboard on bus RS485
DVTOUCH is a full screen touch screen keyboard (touch
sensitive) used for the control of CE100-3BUS or CE-LAN
control panels. The keyboard is connected to the control unit
via a 4-wire cable that includes power and RS485 bus
communication.
The keyboard screen turns on as soon as it is touched. If it
is not touched for 60 seconds (programmable time) the
screen turns off automatically.
The icons on the screen can change according to the control
panel to which the keyboard is connected (always refer to
the control panel manual).
The keyboard has a buzzer that emits acoustic signals
("beep"); it is possible to enable/disable the acoustic signals
and change the tone of the “beeps”.
The keyboard consists of two parts: a main body (1) and a
base (2), used for fixing to the wall.
1. Identification of the parts
1 –Main body
2 –Mounting base
3 –Locking screw
4 –Release slots
2. Installation
Do not use the device outdoors.
The keyboard must be installed on a flat surface using the
supplied mounting base. The main body (1) is hooked onto
the wall mounting base (2). Proceed as follows:
1. Unscrew the locking screw on the lower side (3)
2. Release the base levering on the slots on the lower
side (4)
3. Fix the base to the wall with fischer screws (5),
passing the connection cable through the central part
(6). The base must be oriented with the locking screw
down (7).
5 –Wall fixing screws
6 –Cable routing
7 –Base orientation (locking
screw)
4. Connect the four wires of the RS485 bus to the
keyboard terminal block (see the control panel manual)
5. Reassemble the keyboard body on the base fixed to
the wall. Gently press until you hear the anchor clicks
of the 4 hooks.
WARNING: Arrange the connection cable in an orderly
manner, avoiding it being pinched during closing
6. Tighten the locking screw on the lower side (3)
WARNING: Do not over tighten the screw - Use only
the screw supplied
3. Dip-switch
DIP
ON
OFF
1
120 Ohm bus
termination
Termination
enabled
Termination
disabled
2
NOT USED
1
2
3
4
4
7
5
6
CLIC
K
CLIC
K
CLIC
K
CLIC
K

4. Connections
+
Positive power supply
-
Negative power supply
A
Pole “A” RS485 signal
B
Pole “B” RS485 signal
See control panel manual for connection details.
5. Keyboard programming
1. Connect the keyboard to the control panel and connect
power supply (consult the control panel manual)
2. Press the KEYBOARD SETUP icon for 3 seconds:
3. The first item of the keyboard programming menu
appears on the display (DEFAULT IS ITALIAN).
Use the buttons ▼ and ▲ to move between options
Press “  ”to enter the displayed option
To edit a value:
•Use the numeric keys or the keys ◄and ►
•Confirm changes with “  ”
•Cancel changes with “  ”.
Options
Function
Default
Language
Keyboard language selection
Values: Italiano, English, Francais,
Espanol, Deutsch
Italiano
Address
Keyboard address
Values: 1 ÷ 8
1
Acoustic
signal
Enable buzzer beeps
Values: ON / OFF
ON
Signal
tones
Select tone buzzer sounds
Values: 0 (severe) ÷ 9 (acute)
3
Siren
ringtone
Enable buzzer bell for panel alarm
Values: YES / NO
NO
! WARNING !
ENABLE only to perform a system test.
DISABLE in normal operation.
Time LCD
light
Set screen on time
Values: 0 ÷ 99 seconds
60 sec
Tamper
enable / disable the anti-opening
tamper
Values: YES / NO
SI
Tipo
centrale
Select panel model
Values: CE-1003, CE-LAN
CE-LAN
Erase all
Delete the programming and returns to the
factory setting
End
programm
Exit programming
4. To exit programming, select "End Programming" and
press “  ”.
NOTE: The keypad automatically exits programming
if no key is pressed for 30 seconds.
6. Keyboard display
At rest the screen is off. It lights up as soon as it is touched
or a new event occurs in the control panel. The screen
shows the status of the control panel and allows its control
(always refer to the control panel manual).
NOTICE: The icons may change according to the
control panel to which the keyboard is connected
(always refer to the control unit manual).
S1 ÷ S4
Arming and status keys
1 ÷ 9
Numeric keys
Change values or enter user and installer
codes
Alert
Hashtag
Panel Disarm / Sound
►◄▼▲
Direction keys
Move selection or change values
OK
Confirm and change values
Clear
Exit, delete or cancel
GSM Status
Panic Alarm
(long press for 3 seconds)
Silent alarm
(long press for 3 seconds)
Keyboard programming
(long press for 3 seconds)
Installer / User Menu (only CE100-3 panel)
(long press for 3 seconds)
7. Technical data
Power supply
10 ÷ 14 V (typical 12 V )
Consumption
Stand-by 80 mA –Max 150 mA
Temperature
0 ÷ 40 °C
TASTIERA
CENTRALE
TASTIERA
Program.Tastiera
Selez.Lingua
S1 S2 S3 S4
12 3 4
5 6 7 8
▲
TASTIERA
CENTRALE
◄►
▼
9 0
17:20 21/02/20
Disarmed
S1 S2 S3 S4
12 3 4
▲
TASTIERA
CENTRALE
◄►
5 6 7 8
▼
9 0
EU DECLARATION OF CONFORMITY
Hereby, DUEVI declares that the equipment type “Wired Touch Screen Keypad”
mod. DV-TOUCH is in compliance with Directive EMC 2014/30/EU. The full text
of the EU Declaration of Conformity is available at the internet address
www.duevi.eu